Search Results

An oil-cooled engine has been developing to achieve better warm-up performance. The oil-cooled engine has an oil jacket that pass through around the exhaust port and the cylinder liner. Fins were installed inside the oil jacket to enhance cooling performance. The result of a bench test shows that the fins enhance the cooling performance with slight loss of warm-up performance. The aim of this study is to clarify effects of the fins. This study conducted two simulations. One is a cooling simulation that was conducted to clarify the reason why the fins enhanced the cooling performance. The other is a warm-up simulation that was conducted to clarify the reason why the fins almost maintained the warm-up performance. The cooling simulation was conducted by steady flow simulation. It simulated a full-load operation of the bench test. It compared converged temperature between the engines with/without the fins. The warm-up simulation was conducted by unsteady flow simulation.

The aim of this study is to analyze the emission improvement in the oil-cooled engine by use of internal cylinder gas pressure measurement and 3D simulation of thermal flow and combustion. In the previous study, two test engines were designed to evaluate the benefits of the oil-cooled engine. One was an oil-cooled, and the other was a water-cooled engine. Both engines were single cylinder engines with SOHC valve-train systems. The hardware specifications of both engines were exactly the same except for their cooling systems in order to clarify how the difference in engine cooling system affects their cooling performance, warm-up performance and emission performance.

Improvement of warming performance is required for engine cooling system, because such improvement has an important role for lower emissions. However, the cooling performance and the warming performance of engine are related to the transactions. To improve such trade-off relation between the two performances, oil-cooled system was developed which components are simpler than conventional water-cooled system with a single cylinder, 339cc engine. The oil-cooled system has an “oil jacket” that closely encircles the combustion chamber to cool the cylinder head and cylinder sufficiently. This system adopts the engine lubrication oil to cool combustion chamber, thus the average temperature of the combustion chamber is higher than usual water-cooled engine that enables better warming performance.

A simultaneous multi-composition analyzing (SMCA) resonance enhanced multi-photon ionization (REMPI) system was used to investigate gasoline engine exhaust. Observed peaks for exhaust were smaller mass numbers than those from diesel exhaust. However, large species up to three ring aromatics were observed suggesting that soot precursor forms even in the gasoline engine. At low catalyst temperature condition, the reduction efficiencies of a three-way catalyst were higher for higher mass numbers. This result indicates that the larger species accumulate in the catalyst or elsewhere due to their lower vapor pressures. To evaluate the emission of low volatility species, the accumulation should be taken into account. In the hot mode, reduction efficiencies for aromatic species of three-way catalyst were almost 99.5% however, they fall to 70% in the cold start condition.

Real-time analysis of benzene in automobile exhaust gas was performed using the Jet-REMPI (supersonic jet / resonance enhanced multi-photon ionization) method. Real-time benzene concentration of two diesel trucks and one gasoline vehicle driving in Japanese driving modes were observed under ppm level at 1 s intervals. As a result, it became obvious that there were many differences in their emission tendencies, because of their car types, driving conditions, and catalyst conditions. In two diesel vehicle, benzene emission tendencies were opposite. And, in a gasoline vehicle, emission pattern were different between hot and cold conditions due to the catalyst conditions.

A simple real-time measurement system for the components of volatile organic compounds (VOCs) and polyaromatic hydrocarbons (PAHs) in automobile exhaust gas using a laser ionization method was developed. This method was used to detect VOCs and PAHs in the exhaust gas of a diesel truck while idling, at 60 km/h, and in the Japanese driving mode JE05. As a result, various VOCs and PAHs, such as xylene and naphthalene, were simultaneously detected, and real-time changes in their concentration were obtained at 1 s intervals.

Supersonic jet / resonance enhanced multi-photon ionization (Jet-REMPI) technique was focused on the analyzing method for gas mixture like exhaust gas from automobiles. In this method, when the mass number and wavelength of excitation laser are determined adequately, the target compound can be monitored selectively. We developed a new analyzer utilizing REMPI method. Using this analyzer, real-time monitoring of exhaust gas from a motorcycle and diesel vehicles was conducted. As a result of real-time monitoring test of the vehicles, concentrations of aromatic compounds like benzene toluene etc. were quantified and real-time changes of their concentrations were observed.

A new five-speed automatic transaxle, U150E, has been developed for FWD passenger cars. The goals of the development of this transaxle are fuel economy improvement, better acceleration performance, and a smoother shift feel. U150E achieved its targets by adopting a wide gearing range and using hydraulic control system design based on various simulations. This paper describes the major features, performance of this automatic transaxle, and technical points of the development.