Search Results

The automotive industry is continuously striving to reduce vehicle mass by reducing the mass of components including wheel bearings. A typical wheel bearing assembly is mostly steel, including both the wheel and knuckle mounting flanges. Mass optimization of the wheel hub has traditionally been accomplished by reducing the cross-sectional thickness of these components. Recently bearing suppliers have also investigated the use of alternative materials. While bearing component performance is verified through analysis and testing by the supplier, additional effects from system integration and performance over time also need to be comprehended. In a recent new vehicle architecture, the wheel bearing hub flange was reduced to optimize it for low mass. In addition, holes were added for further mass reduction. The design met all the supplier and OEM component level specifications.

The effects of nitrogen-enriched air, supplied by an air separation membrane, on NOx emissions from a 1.9-L turbocharged direct-injection diesel engine were investigated. To enrich combustion air with more nitrogen, prototype air separation membranes were installed between the after-cooler and intake manifold without any additional controls. The effects of nitrogen-enriched combustion air on NOx emissions were compared with and without exhaust gas recirculation (EGR). At sufficient boost pressures (>50 kPag), nitrogen-enriched air from the membrane provided intake oxygen levels that were similar to those of EGR. Compared with EGR, nitrogen-enriched air provided 10-15% NOx reductions during medium to high engine loads and speeds. At part loads, when turbocharger boost pressure was low, the air separation membrane was not effective in enriching air with nitrogen. As a result, NOx reduction was lower, but it was 15-25% better than when EGR was not used.

Nearly 80% of all emissions from an automobile during the Federal Test Procedure (FTP) occur within the first two minutes of the test because the engine is running rich and the catalyst has not reached peak operating temperature. Research at Compact Membrane Systems, Inc. have proven the benefit of using the engine's natural vacuum to drive a membrane module to supply Oxygen Enriched Air (OEA) during initial start up. The benefit of the OEA has shown to decrease emissions of carbon monoxide (CO) and hydrocarbons (HC). In addition, OEA helps to maintain the combustion flame stability when the engine is operated in a lean mode or at a low engine speed. There is evidence that OEA may also account for to a shorter warmer up time for the catalyst. A 3 inch diameter by 9 inch long module, (7.5 cm dia. × 23 cm) with a small regenerative blower, was installed to an accessory port on the intake manifold of a truck engine.

Exhaust emissions consisting of oxides of nitrogen (collectively known as NOx) from internal combustion engines present a serious environmental problem. Although the problem exists for both gasoline and diesel engines, the problem is more severe for the diesel engine. NOx formation in an engine depends strongly on flame temperature, and flame temperature is dependent upon the composition of the fuel and the intake air. The concept is to develop and test copolymer modules for Nitrogen Enriched Air (NEA) supply to diesel engines. The objective is to minimize NOx production from diesel engine emissions without a significant loss of fuel efficiency or a significant increase in carbon monoxide and smoke related emissions. In the present study, a module using the latest membrane technology was designed, tested and fabricated. The modules were installed in a diesel engine test stand and tests were run. The NOx level from the test engine using standard air was established.

Air can be enriched with oxygen and/or nitrogen by selective permeation through a nonporous polymer membrane; this concept offers numerous potential benefits for piston engines. The use of oxygen-enriched intake air can significantly reduce exhaust emissions (except NOx), improve power density, lessen ignition delay, and allow the use of lower-grade fuels. The use of nitrogen-enriched air as a diluent can lessen NOx emissions and may be considered an alternative to exhaust gas recirculation (EGR). Nitrogen-enriched air can also be used to generate a monatomic-nitrogen stream, with nonthermal plasma, to treat exhaust NOx. With such synergistic use of variable air composition from an on-board polymer membrane, many emissions problems can be solved effectively. This paper presents an overview of different applications of air separation membranes for diesel and spark-ignition engines. Membrane characteristics and operating requirements are examined for use in automotive engines.