Search Results

This study examined a method of predicting the piston temperature in reciprocating internal combustion engines with the aim of developing lightweight pistons. Since the piston temperature is strongly affected by the in-cylinder temperature distribution and turbulence, it is necessary to consider the effects of flame propagation, cooling by the intake air, temperature rise due to combustion, in-cylinder flow and the combustion chamber shape. A three-dimensional combustion simulation that can take these effects into consideration was run to calculate the heat transfer coefficient from the piston crown surface and the gas temperature. The results were used as the boundary conditions for an analysis of heat transfer from the piston, and a method was thus developed for analyzing the piston temperature.

Research is under way on an engine system [1] that achieves a variable compression ratio using a multiple-link mechanism between the crankshaft and pistons for the dual purpose of improving fuel economy and power output. At present, there is no database that allows direct judgment of the feasibility of the specific sliding parts in this mechanism. In this paper, the feasibility was examined by making a comparison with the sliding characteristics and material properties of conventional engine parts, for which databases exist, and using evaluation parameters based on mixed elasto-hydrodynamic (EHD) lubrication calculations. In addition, the innovations made to the mixed EHD calculation method used in this study to facilitate calculations under various lubrication conditions are also explained, including the treatment of surface roughness, wear progress and stiffness around the bearings.

A multiple-link variable compression ratio (VCR) mechanism is suitable for a long-stroke engine by providing the following characteristics: (1) a nearly symmetric piston stroke and (2) an upper link that stays vertical around the time of the maximum combustion pressure. These two characteristics work to reduce force inputs to the piston. The maximum inertial force around top dead center is reduced by the effect of the first characteristic. The second characteristic is effective in reducing piston side thrust force and helps ease piston pin lubrication. Because of the combined effect of these characteristics, the piston skirt can be made smaller and the piston pin can be shortened. That makes it possible for the piston skirt and piston pin to move between the counterweights, resulting in a downward extension of the piston stroke. As a result, a longer-stroke engine mechanism can be achieved without making the cylinder block taller.

A continuously variable valve event and lift (VEL) system, actuated by oscillating cams, can provide optimum lift and event angles matching the engine operating conditions, thereby improving fuel economy, exhaust emission performance and power output. The VEL system allows small lift and event angles even in the engine operating region where the required intake air volume is small and the influence of valvetrain friction is substantial, such as during idling. Therefore, the system can reduce friction to lower levels than conventional valvetrains, which works to improve fuel economy. On the other hand, a distinct feature of oscillating cams is that their sliding velocity is zero at the time of peak lift, which differs from the behavior of conventional rotating cams. For that reason, it is assumed that the friction and lubrication characteristics of oscillating cams may differ from those of conventional cams.

The authors have previously proposed an engine system that uses a new piston-crank system incorporating a multiple-link mechanism to vary the piston's motion at top dead center and thereby obtain the optimum compression ratio matching the operating conditions. This multiple-link variable compression ratio (VCR) mechanism can be installed without increasing the engine size or weight substantially by selecting a suitable type of link mechanism and optimizing the detailed specifications. Previous papers by the authors have made clear the features of the VCR mechanism that facilitates continuously variable control of the compression ratio [1][2]. It was shown that engine friction attributable to piston-side thrust can be reduced through an upright orientation of the upper link in the expansion strokes.

This paper presents a variable compression ratio (VCR) system that has a new piston-crankshaft mechanism with multiple links. This multi-link mechanism varies the piston position at top dead center (TDC), making it possible to change the compression ratio of the engine continuously. Previous attempts have been made to achieve variable compression ratio with this type of method, but it was difficult to avoid various undesirable effects such as an increase in the engine size, substantial weight increases, increased engine block vibration due to a worsening of piston acceleration characteristics and increased friction resulting from a larger number of sliding parts. At the stage of developing the basic design of the multi-link geometry, emphasis was placed on selection of a suitable link geometry and optimization of the detailed dimensions with the aim of essentially resolving these previous issues.

Modern engine bearings have been operating under very harsh conditions. Consequently, a bearing wear propagates for a short time and a fatigue sometimes occurs on high loaded region. To reproduce the bearing damage in actual engines, the operating conditions of engine bearing were simulated on a rig test machine. The bearing wear was measured until the fatigue crack occurred in the simulation test. The wear progressed at the edges of the bearing length and the crack also was observed near the edges. The bearing damage is influenced by the bearing design and operating conditions. The experiment was conducted to change the design parameters in conditions. The experimental results were compared to the calculated results based on the elastohydrodynamic lubrication (EHL) theory. The correlation between bearing damage and bearing performance by theoretical analysis were investigated on effects of the design parameters.

The possibility of predicting engine bearing durability by elastohydrodynamic lubrication (EHL) calculations was investigated with the aim of being able to improve durability efficiently without conducting numerous confirmation tests. This study focused on the connecting rod big-end bearing of an automotive engine. The mechanisms of wear and fatigue, which determine bearing durability, were estimated by comparing the results of EHL analysis and experimental data. This comparison showed the possibility of predicting the wear amount and the occurrence of fatigue by calculation.

Engine bearings today are operating under very harsh conditions. Consequently, a wear propagates for a short time and a fatigue sometimes occurs on the bearings. In present study, on the rig test machine, the operating conditions of engine bearing were simulated to reproduce the bearing damage. The bearing wear was measured until the fatigue crack occurred. The bearing wear increased at the edges of the bearing length and the crack also was observed near the edges. The experimental results were compared to the calculated results based on the elastohydrodynamic lubrication (EHL) theory. The correlations between the bearing damage and the bearing performances by the theoretical analysis were investigated.

Improving the durability and reliability of crankshaft bearings has become an important issue for automotive engines recently because of conflicting demands for lower fuel consumption and higher power output. This study focused on the connecting rod big-end bearing which is subjected to harsher operating conditions on account of these requirements. It is known that the crank pin journal temperature is an indicator of big-end bearing seizure. Having a simple method for predicting the crank pin journal temperature with the required accuracy at the design stage is indispensable to efficient engine development. In this study, analyses were first conducted to determine the oil flow rate at the big-end bearing which is a major determinant of the crank pin journal temperature.

It is important to understand the influence of housing stiffness on bearing performance, particularly for the connecting rod bearings of automotive engines. It is known that the engine lubricant shows a piezoviscous characteristic whereby its viscosity changes under the influence of pressure. Engine bearings under a heavy load are apt to be influenced in this way. In this study, the effects of connecting rod stiffness and lubricant piezoviscosity on bearing performance were examined by elastohydrodynamic lubrication (EHL) analysis under conditions corresponding to the high-speed operation of an actual engine. The results indicated that under such heavy load conditions housing stiffness greatly affects friction loss because of lubricant piezoviscosity. It was also found that the piezoviscosity of the lubricant has a large effect on bearing performance, as does its viscosity under atmospheric pressure.