Search Results

The present study helps to understand the local combustion characteristics of PREmixed Mixture Ignition in the End-gas Region (PREMIER) combustion mode while using increasing amount of natural gas as a diesel substitute in conventional CI engine. In order to reduce NOx emission and diesel fuel consumption micro-pilot diesel injection in premixed natural gas-air mixture is a promising technique. New strategy has been employed to simulate dual fuel combustion which uses well established combustion models. Main focus of the simulation is at detection of an end gas ignition, and creating an unified modeling approach for dual fuel combustion. In this study G-equation flame propagation model is used with detailed chemistry in order to detect end-gas ignition in overall low temperature combustion. This combustion simulation model is validated using comparison with experimental data for dual fuel engine.

An applicable and comprehensive control strategy of a natural gas/diesel dual fuel engine is presented in this paper. The dual fuel engine is converted from a conventional mechanical pump, turbo charged, heavy duty diesel engine. In the dual fuel mode, the pedal position is explained as demanded total fuel quantity, the quantity of pilot diesel and natural gas are calculated in order to provide the equal energy with the original diesel engine at the same operation condition, the proportion of the natural gas is primarily determined by the load rate and the speed of the engine. When the engine is working under light or moderate load, the intake air is throttled in order to improve the brake mean effective pressure and reduce the hydrocarbon emissions of the dual fuel engine, according to target excess air ratio and the quantities of the two fuels, the desired air mass per cycle can be obtained.

With increasing interest to reduce the dependency on gasoline and diesel, alternative energy source like compressed natural gas (CNG) is a viable option for internal combustion engines. Spark-ignited (SI) CNG engine is the simplest way to utilize CNG in engines, but direct injection (DI) Diesel-CNG dual-fuel engine is known to offer improvement in combustion efficiency and reduction in exhaust gases. Dual-fuel engine has characteristics similar to both SI engine and diesel engine which makes the combustion process more complex. This paper reports the computational fluid dynamics simulation of both DI dual-fuel compression ignition (CI) and SI CNG engines. In diesel-CNG dual-fuel engine simulations and comparison to experiments, attention was on ignition delay, transition from auto-ignition to flame propagation and heat released from the combustion of diesel and gaseous fuel, as well as relevant pollutants emissions.

Natural gas has been considered to be one of the most promising alternative fuels due to its lower NOx and soot emissions, less carbon footprint as well as attractive price. Furthermore, higher octane number makes it suitable for high compression ratio application compared with other gaseous fuels. For better economical and lower emissions, a turbocharged, four strokes, direct injection, high pressure common rail diesel engine has been converted into a diesel/natural gas dual-fuel engine. For dual-fuel engine operation, natural gas as the main fuel is sequentially injected into intake manifold, and a very small amount of diesel is directly injected into cylinder as the ignition source. In this paper, a dual-fuel electronic control unit (ECU) based on the PowerPC 32-bit microprocessor was developed. It cooperates with the original diesel ECU to control the fuel injection of the diesel/natural gas dual-fuel engine.

Natural gas has become an attractive alternative for diesel fuel due to its higher octane number, richer reserves and lower price. It has been utilized in compression ignition engines to obtain a higher thermal efficiency compared with spark ignition engines. However, its relatively higher auto-ignition temperature increases the difficulty of compression-ignition based on present hardware devices. One optimal ignition method is that a very small quantity of diesel fuel as the only ignition resource pilot-ignites the lean natural gas-air mixture. This micro diesel pilot-ignited natural gas premixed charge compression ignition (DPING-PCCI) combustion strategy is easy to implement without major hardware modifications, and can significantly reduce the NOx and particle mass emissions from diesel engines. Although the DPING-PCCI has so many advantages, it suffers from poor engine stability and high ultrafine particles emissions at part loads.

This study presents a detailed experimental investigation on the cycle-by-cycle variations in a natural gas/diesel dual fuel engine with EGR. The experiment used a single-cylinder, four-stroke, water-cooled, DI diesel engine. The EGR ratio, diesel injection timing and pilot diesel quantity were varied respectively while all the other parameters were held constant. The parameters of cylinder pressure are used to investigate the cyclic variations. The results show that the cylinder peak pressure, the maximum rate of pressure rise and the indicated mean effective pressure decrease. COVimep increases to 18.9% with 25% EGR ratio. The interdependency between the pressure parameters and their corresponding crank angles become weak with the increasing EGR ratio. The increasing EGR ratio increases the ignition delay. The cylinder peak pressure and the maximum rate of pressure rise increase dramatically with the advance of the pilot diesel injection timing.

A new diffusing-oriented spray stratified combustion system for direct injection gasoline engines is proposed in this study. A reflector with multi-impingement wall head attached ahead of multi-hole injector nozzle is used in this system as a strategy of breaking up the fuel spray and directing it in a desired direction to form a perfect atomization and stratification of fuel air mixture. A comparatively rich fuel-air mixture is always formed over a wide range of engine operation conditions in the vicinity of spark plug due to the fuel spray oriented by the special surface shape of impingement wall, and the finely atomized fuel spray is formed in the other areas of combustion chamber due to the impacting of fuel spray against the impingement wall. Therefore, it is possible to achieve stable and fast burn of lean fuel air mixture. The combustion system is preliminary investigated on a single cylinder four-stroke DI gasoline engine which is shifted from a DI diesel engine.

A simple diaphragm injection carburettor (DIC) is developed and patented by the author in the paper. The principle is that, as the function of the diaphragm mechanism, the pressure difference between two sides of the metering hole equals the vacuum of the Venturi, so it can realize the pressurized fuel metering, by the fuel metering hole and vacuum from the Venturi, and fuel injection. The fuel is injected into the feed port and mixes with the small fraction of air through the port, the main port of fresh air from the crankcase is injected to the cylinder with the scavenging organized so that a separating layer is created between the exhaust and feed port, it can substantially reduce short-circuit. According to the characteristics of low short-circuit at low delivery ratio, the low load fuel supply system of conventional carburettor is preserved and combined with DIC which functions at high load operation.

Proper fuel supply system is the crux to realize the stratified scavenging for small type of two-stroke gasoline engine. A simple and effective diaphragm fuel injection system (DFI) is developed in the paper, which mainly consists of diaphragm pump and injector, the DFI utilizes the crankcase pressure which reflects the inlet flow rate to meter and inject fuel. As low short-circuit at low load operation, stratified scavenging seems not necessary, so the conventional carburetor is preserved to function at low load. This makes the whole fuel system simple and effective. The paper describes the operation principle of the DFI, and results of test on a 30cm3 modified engine are also presented, including the performance of fuel supply and contrast of complex engine performance with the original carbureted engine.