Search Results

A flexible, easily configuration data acquisition system was designed and built for detailed studies of the steady state and dynamic properties of lean NOx traps for an engine dynamometer environment. The system is based on the industry standard VXI backplane. The overriding design philosophy was to design and develop a data acquisition system that was user friendly and could be operated easily by engine laboratory technicians, as well as by test engineers. The primary requirements guiding the design were the following: (1) the ability easily to configure, save, recall, modify, and print test configurations. (2) The ability to configure the gain, channel name, and engineering units for each analog channel. (3) The ability to trigger from one analog input channel. (4) A provision for numeric auto-incrementing of data file names. (5) The ability to save data in Excel™ compatible ASCII format. (6) The utilization of off-the shelf VXI hardware.

When an engine is operated at a lean air-fuel (A/F) ratio, a lean NOx trap (LNT) (or lean NOx catalyst) is needed to increase the NOx conversion efficiency. The presence of sulfur in the fuel degrades the LNT NOx storage capacity and significantly reduces its NOx conversion efficiency. The sulfur degradation is reversible and requires maintaining a temperature of 650 °C at a rich A/F ratio condition (λ < 1.00) for a period of approximately 5 minutes to purge the trap. The desulfation method used here produces an exotherm in an LNT by sequential A/F modulation of the cylinders, resulting in exhaust flows of rich and lean mixtures and creating an exotherm in the LNT (Reference (18). SIMULINK/MATLAB software is used for modeling the temperature and the oxidant-reductant concentrations. The TWC and the LNT are divided into cells. The function of each cell is described using mass and energy balance equations for the gas and solid phases.

A novel method of desulfating lean NOx traps has been developed. Rapid, large amplitude modulation of the air to fuel ratio creates an exotherm of approximately 300°C in the LNT. AFR modulation results in oxidant and reductant breakthough in a three-way catalyst mounted upstream of the LNT. During lean modulation, oxygen is stored in the LNT. During rich modulation, the reductant reacts catalytically with the stored oxygen in the LNT, generating a substantial exotherm. Rich and lean AFR events are selected commensurate with the number of cylinders in the engine, resulting in each cylinder having exactly the same AFR history. This permits a deterministic programming of spark advance and precise coordination of spark advance with the transient fueling effect. The spark advance is retarded for the rich events and increases stepwise for groups of lean events. This strategy results in minimal disturbances in the engine imep.

Oscillating heat transfer is a fundamental phenomenon occurring in Stirling machines and IC engines. A group of relevant dimensionless numbers which characterize this problem is identified by dimensional analysis. The convective heat transfer coefficient, or Nusselt number, is a function of the Reynolds number, the Prandtl number, plus the dynamic Reynolds number and the dimensionless amplitude, when compressibility is not considered. The case for compressible fluid is more complicated. An experiential study confirms above analysis and results in a nonlinear longitudinal fluid temperature distribution in the pipe. The history effect is found to affect the heat transfer rate remarkably. A correlation equation for Nusselt number is obtained by multivariate analysis.

A new method to estimate instantaneous A/F ratio and use the estimation as a feedback signal to control AFR during cold transients, before the oxygen sensor is functional, has been realized by a on-board PCM for a vehicle with a 4.6L, V8, PFI engine [4, 6]. Different AFRs cause variations in flame propagation, causing fluctuations in the effective torque. When a known AFR disturbance is induced into an engine system, a corresponding crankshaft angular velocity fluctuation can be detected. A variable derived from this physical phenomenon can be used to characterize the problem. The optimal fuel perturbation signal is designed by a relaxation concept, and the system model is determined by employing a dual-direction screening multivariate stepwise regression analysis. The estimated AFR is used by the PCM in a closed loop control to correct the fuel during cold transients.

A new estimator for IC engine A/F ratio is described. A/F ratio is important for engine operation since it determines the quantities of engine emissions, such as HC, CO, NOx, the conversion efficiency of catalyst systems, and the engine combustion stability. The A/F ratio estimator described in this paper is based on a fundamental metric that relies on inducing and detecting crankshaft speed fluctuations caused by modulating the engine's fuel injection pulse widths. Fuel pulse width modulation varies the instantaneous combustion A/F ratio crankshaft velocity. Synchronous measurement of crankshaft velocity provides a metric that, when used with other engine state variables as inputs to a conventional neural network, can accurately estimate A/F ratio. The estimator provides A/F information when a physical sensor is not available.

A novel approach is presented to the problem of robust control strategy for an Exhaust Gas Recirculation (EGR) system. Modeling issues and controller design for an electric valve are presented. Robustness is one of the main issues due to nonlinearities (hysteresis, friction), computational time delays, and the effects of complex exhaust gas dynamics. A high level of noise, due to engine vibrations, makes the input-output model identification very difficult. We use a special windowing technique to successfully complete the identification. It was found that a good approximation of the system dynamics consists of a first order transfer function with a time delay whose parameters depend on the operating conditions (engine load, r.p.m.). Thus, the nonlinear effects of friction and hysteresis are replaced, for the purpose of control design, by variable gain, time delay, and time constant of the linear model.

The high cost and complexity of fuel injection pumps are major factors limiting the application of direct fuel injection in internal combustion engines. Recent advances in electronics offer an opportunity for an improvement in this situation. A review and analysis of the electromagnetic spill control concept, in which the pump governor is replaced by solenoid valves, is given. An experimental electromagnetic fuel injection pump and its electronic control system are described, and test results are discussed.

Emission control requirements and the desire for improved fuel economy have led to many studies concerned with improving combustion chamber design, fuel metering, and ignition. This paper describes an experimental programmable ignition system based on a new principle of operation. The ignition system provides for electronically controlled changes in spark duration, spark current level, and restriking rate. The ignition system also combines a very fast risetime with a controlled duration. Extensive multicylinder engine dynamometer test data are presented which indicate that improved ignition can be of benefit at marginal engine operating points.