Search Results

In the present study, we developed a reduced chemical reaction mechanism consisted of n-heptane and toluene as surrogate fuel species for diesel engine combustion simulation. The LLNL detailed chemical kinetic mechanism for n-heptane was chosen as the base mechanism. A multi-technique reduction methodology was applied, which included directed relation graph with error propagation and sensitivity analysis (DRGEPSA), non-essential reaction elimination, reaction pathway analysis, sensitivity analysis, and reaction rate adjustment. In a similar fashion, a reduced toluene mechanism was also developed. The reduced n-heptane and toluene mechanisms were then combined to form a diesel surrogate mechanism, which consisted of 158 species and 468 reactions. Extensive validations were conducted for the present mechanism with experimental ignition delay in shock tubes and laminar flame speeds under various pressures, temperatures and equivalence ratios related to engine conditions.

A multi-step acetone-butanol-ethanol (ABE) phenomenological soot model was proposed and implemented into KIVA-3V Release 2 code. Experiments were conducted in an optical constant volume combustion chamber to investigate the combustion and soot emission characteristics under the conditions of 1000 K initial temperature with various oxygen concentrations (21%, 16%, 11%). Multi-dimensional computational fluid dynamics (CFD) simulations were conducted in conjunction under the same operation conditions. The predicted soot mass traces showed good agreement with experimental data. As ambient oxygen decreased from 21% to 11%, ignition delay retarded and the distribution of temperature became more homogenous. Compared to 21% ambient oxygen, the peak value of total soot mass at 16% oxygen concentration was higher due to the suppressed soot oxidation mechanism.

Internal Combustion Engine (ICE) consumes approx. 2/3 of the oil in the word and 30-40% of the fuel combustion energy in an ICE is wasted in the form of thermal energy in the exhaust gas stream. Exhaust gas thermal energy recovery demonstrates a great potential for overall system thermal efficiency improvements and fuel saving. In this paper different exhaust gas energy recovery bottoming cycles have been analyzed and discussed based on fundamental thermodynamics theory. The typical bottoming cycles are classified into two categories: i.e. direct and indirect energy recovery bottoming cycles. New terms, i.e. Energy Recovery Efficiency (ERE), Energy Conversion Efficiency (ECE) and Overall Energy Conversion Efficiency (OECE) are proposed for the purposes of easier to analyze and easier to compare among the various bottoming cycles. Simplified formulas are derived to demonstrate the key design and operating parameters which define or limit the energy recovery potential.

With its advantages on cost and performance, the integrated exhaust manifold (casting with the turbine) is being used on more vehicles by auto makers. Generally, when compared with the divided exhaust manifold, the integrated exhaust manifold stands for higher vibratory excitation from gas dynamics. In this paper, the gas dynamics excitation has been computed through the GD (gas dynamics) software GT-Power which calculates the exhaust pipe surface pressure, and CFD code Star-CCM+ which calculates the turbine blade force. And the response of manifold has been solved under this excitation. On the other hand, the mechanical excitation has been computed through the MBD (multi-body dynamics) platform AVL-Excite-PU, and the responses under the gas excitation plus the mechanical load have been studied in order to analyze the effects of the fluid excitation on an integrated manifold.

Due to its load control strategy via fresh charge quantity, pumping loss in a homogenous charge gasoline engine is a significant contributor to the high fuel consumption rate at light load. Exhaust gas recirculation (EGR) and lean burn technologies are the common means to reduce gasoline engine pumping loss for fuel economy improvement. Many previous publications compared the EGR and lean burn concepts. However, few of those were able to compare the EGR and lean burn concepts under the same in-cylinder dilution basis. Usually the un-swept in-cylinder residual gas fraction (RGF), which can be significant at very low loads, was ignored due to lack of appropriate method to determine it. Also the theoretical potential and practical limitations were rarely discussed. In this paper, a Naturally Aspirated (NA) gasoline engine was systematically tested for both the EGR and lean mixture concepts on an engine dyno. under the same speed and load conditions.

In engine radiated noise analysis, the conventional boundary element method (BEM) is unsuitable for conducting large-scale acoustic simulations because of low calculation efficiency. The Fast Multipole boundary element method (FMBEM), although greatly improved calculation efficiency for large-scale acoustic simulations, has the problem of low efficiency at the low frequency region and low accuracy at the high frequency region. Those methods cannot meet the requirements of design engineers to get the results in a couple of days. In order to solve the powertrain radiated noise problems accurately and efficiently, some simplified methods and scripts were developed in big-three auto makers and suppliers, such as DIRA. Those scripts are very fast and can meet the timing requirement, but generally, without clear physical meaning.

As the issue of oil shortage and air pollution caused by automotive engine emissions become more and more serious day by day, researchers and engineers from all over the world are seeking for alternative fuels of lower pollution and renewable nature. This paper discusses in detail the feasibility of fueling gasoline engines with Butanol-gasoline blends. Besides the production, transportation, storage, physical and chemical properties of Butanol-gasoline blends, the combustion characteristics were analyzed as well. As the result Butanol was considered an excellent alternative fuel for gasoline engines, with many unique advantages superior to Natural Gas, LPG, Carbinol and Ethanol, the latter are widely studied at present time. In order to validate the above conclusions in engine application, engine dyno tests were conducted for a gasoline engine fueled with different concentrations of Butanol blend ranging from 10% to up to 35%.

A comparison study on the commonly used solution schemes of one-dimensional gas flow in IC engine manifolds, i.e. the method of characteristics and the finite difference schemes, was conducted in this paper. The study was based on computer simulations of the flow in a typical pipe-volume configuration under both steady and unsteady boundary conditions. The simulation results indicate that all the solution schemes offered fairly good accuracy in parallel pipes under steady flow conditions. However, under unsteady flow conditions, especially in tapered pipes commonly used in IC engine manifolds, all the existing solution schemes encountered difficulties. These included such aspects as the mass and energy conservation, non-physical overshoot, solution stability and physical process distortion. The solution schemes were compared based on the case calculations and the related problems are specified.