Search Results

Thermoacoustic engine has been proven to be a promising technology for automotive exhaust waste heat recovery to save fossil fuel and reduce emission thanks to its ability to convert heat into acoustic energy which, hence, can be harvested in useful electrical energy. In this paper, based on the practical thermodynamic parameters of the automotive exhaust gas, including mass flow rate and temperature, two traveling-wave thermoacoustic engines are designed and optimized for the typical heavy-duty and light-duty vehicles, respectively, to extract and reutilize their exhaust waste heat. Firstly, nonlinear thermoacoustic models for each component of a thermoacoustic engine are established in the frequency domain, by which any potential steady operating point of the engine is available.

Extraction and utilization of automotive waste exhaust heat is an effective way to save fuel and protect the environment. One promising technology for this purpose is the thermoacoustic engine, where thermal energy is converted to mechanical energy in terms of high amplitude oscillations. The core component in a travelling-wave thermoacoustic engine is its regenerator where the process of energy conversion is mainly realized. This paper introduces a strategy for the design of the regenerator for applications in typical light- and heavy-duty vehicles. Starting from 1-D linear thermoacoustic theory, the nonlinear effects (given by the high amplitude oscillations) are modelled as acoustic resistances and introduced into the basic linear equations to estimate the nonlinear dissipations in the regenerator. Then, a few dimensionless parameters are derived by normalizing these thermoacoustic equations.

In this paper, the travelling-wave thermoacoustic engine (TAE) and its application for recovery of waste heat from automotive exhaust systems is investigated. The aim is to give some insight into the potential, but also limitations of the technique for practical applications. This includes packaging, physical boundary conditions as heating and cooling available, but also system perspectives as influence of legislative drive cycles and degree of hybridization. First, the travelling-wave TAE is described as a low-order acoustic network in the frequency domain. Models, including non-linear effects, are set up for every component in the network to describe the propagation and dissipation of acoustic waves. For a TAE with looped structure, the continuity of pressure and volumetric velocity is employed to determine the saturation pressure, as well as the stable operating point. These models are validated against experimental data available in the literature [1].

Electric vehicles (EVs) have become a hot research topic due to the petroleum crisis and air pollution issues, and Hybrid EVs (HEVs) equipped with engines and motors are popular nowadays due to their advantage over Pure EVs. The energy distribution between the engine and the motor is the major task of the control strategy or energy management for HEVs. Rule-based and optimization-based approaches are developed in this area, but not much work has been done for large-size super-capacitor (SC) equipped HEVs, like Hybrid buses. In this paper, a new optimization-based control strategy for a hybrid bus equipped with SCs as the energy regeneration system is presented. Considering the driving patterns of a bus that is of frequent accelerations and decelerations, it is proposed to characterize each time instant by its speed and acceleration, and the energy distribution is optimized based on these two state variables.

Manufacturing tolerances are inevitable in nature. For the bearings used in internal combustion engines, the manufacturing tolerances of roundness, which is of the micron scale, can be very close to the bearing radial clearance, and as a result the roundness could affect the lubrication of the bearings and thus affecting the friction loss of the engine. However, there is insufficient understanding of this mechanism. This study aims to find out the effects of the amplitude and the phase of journal roundness in the shape of ellipse on the lubrication of engine bearings. The elastohydrodynamic (EHD) theory is applied to model the bearing since the EHD model takes account of the elastic deformation of the journal and the bearing shell. The analysis of the DOE results shows the existence of roundness can be beneficial to the lubrication in some cases.

Conventionally, the engines are calibrated under the assumption that engines will be made exactly to the prints, and all the engines from the same batch will be identical. However, engine-to-engine variations do exist which will affect the engine performances, and part-to-part variations, i.e., the tolerance, is an important factor leading to engine-to-engine variations. There are researches conducted on the influence of dimensional tolerances on engine performance, however, the impact of straightness, which is an important geometric tolerance, on lubrication is an unsolved issue. This study presents a systematic method to model the straightness and to analyze its effects on the friction loss. The bearing model is built based on elastohydrodynamic (EHD) theory. Meanwhile a novel modeling method to represent any form of straightness in three-dimensional space is proposed.

Manufacturing of the internal combustion engines (ICEs) has very critical requirements on the precision and tolerance of engine parts in order to guarantee the engine performance. As a typical complex nonlinear system, small changes in dimensions of ICE components may have great impact on the performance and cost of the manufacturing of ICES. In this regard, it is still necessary to discuss the optimization of the tolerance and manufacturing precision of the critical components of ICEs even though the tolerance optimization in general has been reported in the literature. A systematic process for determining optimal tolerances will overcome the disadvantages of the traditional experience-based tolerance design and therefore improve the system performance.

The internal combustion engine (ICE) is a typical complex multidisciplinary system which requires the support of precision design and manufacturing. To achieve a better performance of ICEs, tolerance assignment, or tolerance design, plays an important role. A novel multi-disciplinary tolerance design optimization problem considering two important disciplines of ICEs, the compression ratio and friction loss, is proposed and solved in this work, which provides a systematic procedure for the optimal determination of tolerances and overcomes the disadvantages of the traditional experience-based tolerance design. A bi-disciplinary analysis model is developed in this work to assist the problem solving, within which a model between the friction loss and tolerance is built based on the Gaussian Process using the corresponding simulation and experimental data.

A generic product development process is usually involved with four Phases [1]: 1. Define Requirements, 2. Select Design Concepts, 3. Optimize Design, and 4. Verify Design. Reliability Verification is an integral part of “Verify Design”, and therefore, plays a critical role in product development. This paper discusses three stages in Reliability Verification: Reliability Verification Plan Reliability Verification Execution Reliability Verification Analysis Most of the elements discussed here were introduced in other literatures. This paper integrates the major elements together and provides an educational overview. It may serve as a quick reference guide for the engineers in industries where reliability verification is required.

Avoiding failure modes is the ultimate goal of reliability engineering [1, 2]. Design for Six Sigma [3] coupled with Transfer Function [4] analysis is a process that can help to achieve this goal at every stage of product design process. In this paper, the authors integrate Design for Six Sigma and Transfer Function into an Engineering Plan for Failure Mode Avoidance. The authors also define the Distance from Failure Mode with an example of beam.

As automotive competition is becoming more and more global, automotive products (vehicles or systems or components) are often developed in one market and made and/or used in other markets. The operating conditions are often different from one market to another market. If the market unique operating conditions are not considered in its development and manufacture process, the product may not fully perform its intended function over useful life period, and may experience fewer failure modes in one market but more or different failure modes in other markets. This paper presents a Reliability Engineering approach, based on “Failure Mode Avoidance”, to the product development for global automotive markets. The approach includes three phases: Discover operating conditions (noise factors) and their potential failure modes Develop countermeasures to deal with the noise factors, and Verify the effectiveness of the countermeasures using Reliability Demonstration Matrix.

In this paper, a simplified and systematic approach to integrate reliability and durability aspects in design process is presented. A six step process is explained with the help of examples. Two alternatives for gathering means and standard deviations for key parameters are discussed. First a DOE approach based on orthogonal arrays is presented. Second approach is based on Taylor Series expansion. An example of beam design is solved with both of these approaches. The Second example also considers the degradation with time in service.

The study has been conducted to analyze the effect of interlaminar stresses on the crush behavior of laminated composite structures. Several sets of test data of columns under axial crush load were analyzed. Modes of collapse were identified. Interlaminar stresses due to in-plane axial crush load were calculated and compared with interlaminar strengths. The analysis showed that when laminates have no significant cracks or voids, the interlaminar stresses have no effect on crush mode up to the maximum load, and a thin-walled composite column fails in local buckling mode. When the laminates have initial imperfections, cracks or voids create interlaminar stress concentration and cause the delamination failure. In this case the column walls are split through the thickness into two portions, one crushed inward and the other crushed outward. The study also indicated that fiber orientation is important in initiating interlaminar stresses.