Search Results

A constant volume spray and combustion vessel utilizing the pre-burn mixture procedure to generate pressure, temperature, and composition characteristic of near top dead center (TDC) conditions in compression ignition (CI) engines was modified with post pre-burn gas induction to incorporate premixed methane gas prior to diesel injection to simulate processes in dual fuel engines. Two variants of the methane induction system were developed and studied. The first used a high-flow modified direct injection injector and the second utilized auxiliary ports in the vessel that are used for normal intake and exhaust events. Flow, mixing, and limitations of the induction systems were studied. As a result of this study, the high-flow modified direct injection injector was selected because of its controlled actuation and rapid closure. Further studies of the induction system post pre-burn were conducted to determine the temperature limit of the methane auto-ignition.

Natural gas offers the potential to reduce greenhouse gas emissions from heavy-duty on-road transportation. One of the challenges facing natural gas as a fuel is that its composition can vary significantly between different fuel suppliers and geographical regions. In this work, the impact of fuel composition variations on a heavy-duty, direct injection of natural gas engine with diesel pilot ignition is evaluated. This combustion process results in a predominantly non-premixed gaseous fuel combustion event; as a result, end-gas autoignition (knock) is not a concern. Changes in the fuel composition do still impact the combustion, both through the changes in the chemical kinetics of the reactions and due to changes in the density of the fuel. Increasing concentrations of heavier hydrocarbons, such as ethane or propane, in the fuel lead to higher fuel densities and hence greater fuel mass being injected for a given injection duration.

Retaining the diesel combustion process but burning primarily natural gas offers diesel-like efficiencies from a natural-gas fuelled heavy-duty engine. This combustion event is limited by the injection pressure of the fuel, as this dictates the rate of mixing and hence of combustion. Typical late-cycle direct injection applications are limited to approximately 300 bar fuel pressure. The current work reports on tests for the first time at natural gas injection pressures up to 600 bar. The results show that significant efficiency and particulate matter reductions can be achieved at high loads, especially at higher speeds where the combustion is injection rate limited at conventional pressures. Increases in combustion noise and harshness are a drawback of higher pressures, but these can be mitigated by reducing the diameter of the nozzle gas holes to control the fuel injection rate.

Conditional source-term estimation (CSE) is a novel chemical closure method for the simulation of turbulent combustion. It is less restrictive than flamelet-based models since no assumption is made regarding the combustion regime of the flame; moreover, it is computationally cheaper than conventional conditional moment closure (CMC) models. To date, CSE has only been applied for simulating canonical laboratory flames such as steady Bunsen burner flames. Industry-relevant problems pose the challenge of accurately modelling a transient ignition process in addition to involving complex domaingeometries. In this work, CSE is used to model combustion in a homogeneous-charge natural gas fuelled SI engine. The single cylinder Ricardo Hydra research engine studied here has a relatively simple chamber geometry which is represented by an axisymmetric mesh; moving-mesh simulations are conducted using the open-source computational fluid dynamics software, OpenFOAM.

The effects of the temporal and spatial distributions of ignition timings of combustion zones on combustion noise in a Direct Injection Compression Ignition (DICI) engine were studied using experimental tests and numerical simulations. The experiments were performed with different fuel injection strategies on a heavy-duty diesel engine. Cylinder pressure was measured with the sampling intervals of 0.1°CA in order to resolve noise components. The simulations were performed using the KIVA-3V code with detailed chemistry to analyze the in-cylinder ignition and combustion processes. The experimental results show that optimal sequential ignition and spatial distribution of combustion zones can be realized by adopting a two-stage injection strategy in which the proportion of the pilot injection fuel and the timings of the injections can be used to control the combustion process, thus resulting in simultaneously higher thermal efficiency and lower noise emissions.

An experimental investigation of the autoignition of transient gaseous fuel jets in heated and compressed air is conducted in a shock tube facility. Experiments are performed at an initial pressure of 30 bar with initial oxidizer temperatures ranging from 1150 K to 1400 K, injection pressures ranging from 60 bar to 150 bar, and with injector tip orifice diameters of 0.275 mm and 1.1 mm. Under the operating conditions studied, increasing temperature results in a significant decrease in autoignition delay time, td. The smaller orifice results in an increase in ignition delay time and variability, as compared with the larger orifice. For initial temperatures below about 1250K, ignition is rarely achieved with the smaller orifice, whereas ignition is always achieved with the larger orifice down to 1150 K. Under the conditions studied, increasing the injection pressure decreases ignition delay, a result dynamically consistent with larger orifice size decreasing ignition delay time.

Measurements of ignition characteristics and emissions were made in a shock tube facility operating at engine-relevant conditions. Methane and methane/ethane fuels were injected down the centerline of the shock tube using an electronically controlled prototype gaseous fuel injector developed by Westport Innovations. Air was preheated and compressed using a reflected shock technique that produced run times of 4-5 ms. Particulate matter (PM) emissions were found to be highly intermittent. In only 6 out of 97 experiments was PM detected above background levels. In all of these 6 sooting experiments ignition kernels were located relatively close to the injector tip and ignition occurred prior to the end of fuel injection. Using the large orifice injector tip with pure methane fuel, PM was detected in 4 out of 28 experiments; using the small orifice with pure methane fuel, no PM was detected in any of 50 experiments.

The performance of automotive air conditioning systems could be improved by utilizing more effective control algorithms. This paper describes the development of a real time implementable optimal single zone temperature controller. A bilinear model of the process, including a disturbance is used. A one step ahead control is derived by parameterizing the control on a short horizon. The implementation of the algorithm is demonstrated with both a simulation and an experiment. The results indicate that the technique can produce substantial energy savings and improved rider/occupant comfort.