Search Results

Implementation of EPA's heavy-duty engine NOx standard of 0.20 g/bhp-hr has resulted in the introduction of a new generation of emission control systems for on-highway heavy-duty diesel engines. These new control systems are predominantly based around aftertreatment systems utilizing urea-based selective catalytic reduction (SCR) techniques, with only one manufacturer relying solely on in-cylinder NOx emission reduction techniques. As with any new technology, EPA is interested in evaluating whether these systems are delivering the expected emissions reductions under real-world conditions and where areas for improvement may lie. To accomplish these goals, an in-situ gaseous emissions measurement study was conducted using portable emissions measurement devices. The first stage of this study, and subject of this paper, focused on engines typically used in line-haul trucking applications (12-15L displacement).

Given the complexities of simulating fuel injection, most models contain empirical parameters. This work presents a method of automatically adjusting empirical model parameters in a computational fluid dynamics (CFD) sub-model in order to best agree with an ensemble of experimental measurements. The method is demonstrated by a multiphase flow simulation of flash-boiling fuel injector nozzles. This paper describes a framework to automatically set inputs, launch individual runs, read the output of these runs, and intelligently choose new input values based on the difference between calculated mass flow rates and experimental values, in order to minimize error. The Hooke-Jeeves search algorithm was chosen for the optimization process, since it is reasonably efficient, does not require calculating derivatives, and is robust. The scheme scales well when employed on computer clusters, where numerous calculations can be run simultaneously using a batch queuing system.

This investigation was aimed at measuring the relative performance of two spray-guided, single-cylinder, spark-ignited direct-injected (SIDI) engine combustion system designs. The first utilizes an outwardly-opening poppet, piezo-actuated injector, and the second a conventional, solenoid operated, inwardly-opening multi-hole injector. The single-cylinder engine tests were limited to steady state, warmed-up conditions. The comparison showed that these two spray-guided combustion systems with two very different sprays had surprisingly close results and only differed in some details. Combustion stability and smoke emissions of the systems are comparable to each other over most of the load range. Over a simulated Federal Test Procedure (FTP) cycle, the multi-hole system had 15% lower hydrocarbon and 18% lower carbon monoxide emissions.

Low-speed sideswipe collisions between tractor-semitrailers and passenger vehicles can result in large movements and extensive areas of visible damage to the passenger vehicle. However, depending on the specifics of the collision, the resulting crash pulse may be extended, and the vehicle accelerations correspondingly low. Research regarding the impact environment and resulting injury potential of the occupants during these types of impacts is limited. Five full-scale crash tests utilizing a tractor-semitrailer and a passenger car were conducted to explore vehicle responses during these types of collisions for both the passenger car and the tractor-trailer. The test vehicles included a loaded van semitrailer pulled by a tractor and three identical mid-sized sedans. Instrumentation on the sedans included accelerometers and rotational rate sensors, and the vehicle and occupant kinematics were recorded using onboard and off-board real-time and high-speed video cameras.

Low-speed sideswipe collisions between tractor-semitrailers and passenger vehicles may result in large areas of visible damage to the passenger vehicle. However, due to the extended contact that occurs during these impacts, it is typical in these incidents for the crash pulse duration to be long and the vehicle accelerations to be correspondingly low. Research regarding the impact environment and resulting injury potential of the occupants during these types of impacts is limited. Five full-scale crash tests utilizing a tractor-semitrailer and a passenger car were conducted to explore the occupant responses during these types of collisions. The test vehicles included a van semitrailer pulled by a tractor and three identical mid-sized sedans. The occupants of the sedans included an instrumented Hybrid III 5th -percentile-male anthropomorphic test device (ATD) in the driver's seat and an un-instrumented Hybrid III 5th -percentile-female ATD in the left rear seat.

Far-side occupants are not addressed in current government regulations around the world even though they account for up to 40% of occupant HARM in side impact crashes. Consequently, there are very few crash tests with far-side dummies available to researchers. Sled tests are frequently used to replicate the dynamic conditions of a full-scale crash test in a controlled setting. However, in far-side crashes the complexity of the occupant kinematics is increased by the longer duration of the motion and by the increased rotation of the vehicle. The successful duplication of occupant motion in these crashes confirms that a sled test is an effective, cost-efficient means of testing and developing far-side occupant restraints or injury countermeasures.

Circulation control technologies have been applied to fixed wing aircraft for approximately four decades. During those early tests an increase in lift coefficient of nearly four times the unaltered airfoil was achieved. Applying these or similar technologies, particularly inducing the coanda effect through blowing slots to rotorcraft blades, can enhance the performance of the helicopter. The increase in lift coefficient of the rotor blade provides more options to the designer, including decreasing the rotor diameter, decreasing the rotor speed, increasing the payload capacity, or a combination of all three. By either reducing the diameter and/or the rotor speed the blade tip speed can be reduced, thus allowing a higher forward flight speed. Retreating blade stall can also be reduced by applying circulation control to the leading edge of the rotor blade.

The development of a standardized roll-on, roll-off (RoRo) sensor pallet system for a C-130 aircraft was conceived by the National Guard and the Counter Narco-Terrorism Technology Development Office to assist in counterdrug reconnaissance activities within the United States and surveillance and reconnaissance missions worldwide. West Virginia University was contracted to perform the design and development of this system because of their innovative design ideas. Before development, the design parameters were established by these two DoD agencies, their mission requirements and by the limitations of the C-130 aircraft. These limitations include using Commercial off the Shelf (COTS) and Government off the Shelf (GOTS) items when developing the system that must be universal on all C-130 aircrafts variants B thru H. Further design criteria are by the limitations of the C-130 aircraft and its existing mission requirements.

Compression and power stroke cycles for a 4 stroke cycle spark ignition engine modified by extending the connecting rod to simulate purely sinusoidal piston motion are analyzed over a range of operating speeds and are compared with those of a similar conventional engine. Heat release rate is estimated for both engines using a simple Wiebe function with the functional parameters found via a simplex curve fitting method used in conjunction with experimental pressure curves. It is shown that the functional parameters which represent the combustion and the duration of fuel burn are slightly larger over the range of operation in the sinusoidal engine while the shape factor remains largely the same. However, the pressure-crank angle curves are sufficiently similar such that conventional slider-crank curves can be used to model sinusoidal engines, which was the motivation behind this research.

The application of the Stiller-Smith Mechanism for use in an internal-combustion engine is investigated. The dimensionless stroke-to-bore and stroke-to-gear diameter ratios are used as a design vector. The effect of changes in the design vector upon parameters including mechanical efficiency, internal gear loads, bearing reaction forces, and connecting rod loads is investigated. A composite objective function is defined in which these parameters have variable weighting. An optimal design can be reached by using this function. Characteristics of the mechanism with and without the effect of inertial forces are investigated. Results are presented including three-dimensional sensitivity plots and an optimal design.