Search Results

Cross-sectional distributions of the liquid phase temperatures in fuel sprays were measured using a laser-induced fluorescence technique. The liquid fuel (n-hexadecane or squalane) was doped with pyrene(C16H10). The fluorescence intensity ratios of the pyrene monomer and excimer emissions has temperature dependence, and were used to determine the liquid phase temperatures in the fuel sprays. The measurements were performed on two kinds of sprays. One was performed on pre-heated fuel sprays injected into surrounding gas at atmospheric conditions. The other was performed on fuel sprays exposed to hot gas flow. The spray was excited by laser radiation at 266nm, and the resulting fluorescence was imaged by an intensified CCD camera. The cross-sectional distribution of the liquid phase temperature was estimated from the fluorescence image by the temperature dependence of the intensity ratio.

Spray penetration for Diesel injectors, where injection pressure varies with time during the injection period, was calculated. In order to carry out this calculation, the discharge coefficients of the needle-seat opening passage and discharge hole in orifice-type Diesel nozzles were investigated separately. Simple empirical correlations were obtained between these coefficients and needle lift. Then, by introducing these correlations, the injection pressure, which is defined as the pressure in the sac chamber just upstream of the discharge hole, was either derived from measured fuel supply line pressure, or predicted by means of an injection system simulation. Finally, based on the transient injection pressure, spray tip penetration was calculated by taking the overall line which covers the trajectories of all fuel elements ejected during the injection period.

A high-speed photographic study is presented illustrating the influence of engine variables such as an introduced air swirl, the number of nozzle holes and the piston cavity diameter, on the combustion process in a small direct-injection (D.I.) diesel engine. The engine was modified for optical access from the under and lateral sides of the combustion chamber. This modification enabled a three-dimensional analysis of the flame motion in the engine. The swirling velocity of a flame in a combustion chamber was highest in the piston cavity, and outside the piston cavity it became lower at the piston top and at the cylinder head in that order. The swirl ratio of the flame inside the cavity radius attenuated gradually with piston descent and approached the swirl ratio outside the cavity radius, which remained approximately constant during the expansion stroke. Engine performance was improved by retarding the attenuation of the swirl motion inside the cavity radius.

In the previous study of the authors, it was found that some benefits for the mixture preparation of DI gasoline engines can be offered by splitting the fuel injection, such as the phenomenon of high density liquid phase fuel piling up at the leading edge of the spray can be circumvented. In a further analysis, the vapor quantity in the “stable operating” range (equivalence ratio of vapor ϕv in a range of 0.7≤ϕv≤1.3) was significantly increased by the split injection compared to the single injection. In this work, the mechanism of the effect of the split injection on the mixture formation process was studied by combining the laser-sheet imaging, LIF-PIV and the LAS (Laser Absorption Scattering) technique. As a result, it is found that the spray-induced ambient air motion can help the formation of the more combustible mixture of the split injection whereas it played a minus role of diluting the spray by the single injection.

A phenomenological spray-combustion model of a D.I. Diesel engine was applied to study the engine parameters with potential for reducing NOx and smoke emissions. The spray-combustion model, first developed at the University of Hiroshima in 1976, has been sophisticated by incorporating new knowledge of diesel combustion. The model was verified using data from an experimental, single cylinder, D.I. diesel engine with a bore of 135mm and a stroke of 130mm. After the verification process, calculations were made under a wide range of the engine parameters, such as intake air temperature, intake air pressure, intake swirl ratio, nozzle hole diameter, injection pressure, air entrainment rate into the spray, and injection rate profile. These calculations estimated the effects of the engine parameters on NOx, smoke and specific fuel consumption. As a result of the calculations, an approach for the low NOx and smoke emission engine was found.

The combustion processes in the prechamber and the main chamber of a small indirect injection (I.D.I.) diesel engine were observed simultaneously by high-speed photography. These observations made it possible to characterize the behavior of flames in both chambers, that is, ignition of fuel, developing and rotating flames in the prechamber, and a flame jet spouting into the main chamber. The effect of engine variables, such as fuel injection timing, cross-sectional area of a throat, fuel injector location, and a recess in a piston top, on the combustion process as well as the engine performance were considered. A flame jet spouting into the main chamber separated into two directions and induced two vortexes. Brown sooty flames appeared along the prechamber wall and inside the flame jet which struck on the piston top. The higher-velocity flame jet and the two Intense vortexes induced by the flame jet realized superior fuel consumption and lower smoke emission.

The internal flow of a diesel injection nozzle was studied by using transparent model nozzles to clarify the effects of the flows in the sac chamber and the discharge hole on the spray behaviors. The geometry of the model nozzle was scaled up 10 times the actual nozzle and the injection pressure for the model nozzle was adjusted so as to achieve a Reynolds number at the discharge hole which was the same as an actual nozzle. Aluminium oxide (Al2O3) tracers were used to visualize the flow patterns in the sac chamber. Sequential photographs of the internal flow and the issuing spray plume during the opening process of the needle valve were taken by a high-speed video camera. By locating the discharge hole on the upper side of the sac chamber, the turbulence intensity in the sac chamber increases and the spread angle of the spray plume becomes large.

Mixture formation processes play a vital role on the performance of a D.I. Gasoline engine. Quantitative measurement of liquid and vapor phase concentration distribution in a D.I. gasoline spray is very important in understanding the mixture formation processes. In this paper, an unique laser absorption scattering (LAS) technique was employed to investigate the mixture formation processes of a fuel spray injected by a D.I. gasoline injector into a high pressure and temperature constant volume vessel. P-xylene, which is quite suitable for the application of the LAS technique, was selected as the test fuel. The temporal variations of the concentration distribution of both the liquid and vapor phases in the spray were quantitatively clarified. Then the effects of injection pressure and quantity on the concentration distributions of both the liquid and vapor phases in the spray were analyzed.

In order to investigate the effect of split injections on mixture formation processes in Direct Injection (DI) gasoline engine sprays, an experimental study was conducted applying the laser absorption and scattering (LAS) technique to the sprays using double pulse injections with various dwells and mass ratios. The effects of various dwells and mass ratios between the pulsed injections on the spatial concentration distributions in the spray, the penetration of vapor and liquid phases, and the mean equivalence ratios of the vapor phase and overall spray, were clarified. It was found that the phenomenon of high concentration liquid spray piling up at the leading edge of the spray is avoided by the double injections with enough dwell or appropriate mass ratio. The maximum penetration length of the spray significantly decreases, especially for the liquid phase with high concentration.

A new optical measuring technique of tip penetration of a diesel fuel spray was developed by detecting the arrival times of the spray tip at several light sheets which were preset at various axial locations downstream. Verified by the instantaneous photographic technique, it was confirmed that this technique is effective, with sufficient accuracy, for measuring the spray tip penetration much more easily than the conventional photographic technique. The tip penetrations of diesel sprays injected through single-hole nozzles with various orifice lengths and diameters has been investigated over a wide range of the operating conditions by this technique. The spray injected through two multihole nozzles, either with or without a sac volume, has also been characterized. The results showed that the spray tip penetration is affected somewhat by the operating conditions. Eventually it is affected by the injected fuel momentum flowrate, nozzle geometry and ambient gas density.

Effects of fumigated fuel on the initial combustion stage of a diesel spray were studied by measuring an ignition delay period and rate of heat release, clarifying a self-ignition limit of a fumigated fuel. Combustion experiments on both fumigated diesel fuel and methanol in a direct injection diesel engine gave the following results; a rapid combustion occurs with the methanol fumigation, while, the diesel fuel fumigation slightly changes the combustion of the main spray of diesel fuel injected directly into the combustion chamber. Regarding the rate of heat release, the maximum rate in the initial combustion stage increases rapidly with an increase in methanol fumigation, while for the fumigated diesel fuel, the maximum rate changes only slightly. The ignition delay period affected by fumigated diesel fuel is shorter than that affected by methanol at the same fumigation equivalence ratio and intake temperature.

Although mixture formation is considered important in actual spark ignition engines, A full understanding of the combustion characteristics of a heterogeneous mixture has not yet been achieved. In this study, in order to clarify the effects of a heterogeneous concentration distribution of the fuel-air mixture on the flame propagation process, different degrees of heterogeneously distributed mixtures were created by the motion of a pair of perforated plates in a constant volume combustion chamber. The laser Rayleigh scattering method was applied for quantitative visualizations of these mixture distributions. To control the distribution of the mixture concentration and the turbulence intensity independently, the flow in the chamber and its turbulence intensity were also measured by a laser sheet method and the LDV technique.

New empirical equations to represent the Sauter mean diameter of a spray injected by a diesel nozzle are presented in this paper. In order to determine the new equations, drop sizes of a diesel spray were analyzed by a laser diffraction technique. Liquids with different viscosities and different surface tensions were tested to obtain the generalized empirical equations. The maximum injection and maximum ambient pressures were 90 MPa and 3.0 MPa respectively. Both the minimum value of the injection pressure to produce a fine spray and the Sauter mean diameter increase the greater the viscosity and the surface tension of the liquid. At a high injection velocity, the Sauter mean diameter increases with an increase in ambient pressure, but it decreases when ambient pressure is increased at a low injection velocity.

Distributions of non-evaporating diesel sprays impinging on a simulated combustion chamber wall were observed from various directions while changing some of the experimental parameters, such as nozzle projection and top-clearance. High-speed photography was used in this study to examine the effects of these parameters on the spray distributions. Moreover, the spray distributions were predicted by using a spray model based on a multi-package model. The calculated distributions were displayed three-dimensionally using a volume rendering application developed by the authors. The predicted spray distributions were compared with the experimental results observed from various directions in order to evaluate the spray model.

An experimental study was conducted to investigate the flame propagation characteristics in the presence of a heterogeneous concentration distribution of a fuel-air mixture in order to provide fundamental knowledge of the effects of gaseous mixture concentration heterogeneity on the combustion process. Different propane-air mixture distributions were produced by the reciprocating movements of a pair of perforated plates in a constant volume combustion chamber. The mean equivalence ratio of the fuel-air mixture was varied from 0.7 on the lean side to 1.6 on the rich side, the turbulence intensity in the combustion chamber was also varied at levels of 0.185 m/s, 0.130 m/s, 0.100 m/s, and 0.0 m/s. By an independent control of the mixture distribution and the turbulence intensity in the combustion chamber, the flame structure and flame propagation speed at various heterogeneous levels of the mixture distribution were investigated in detail.

Experiments and modeling of the fuel spray trajectory and dispersion influenced by both a swirling gas flow and wall impingement were performed under simulated direct injection (D.I.) diesel engine conditions at a high pressure and high temperature. A spray was injected into the steady swirling gas flow and impinged on the simulated piston cavity wall in a constant-volume bomb. High-speed Schlieren photographs provided the informative data on the behavior of the spray vaporizing in such diesel-like circumstances. A simplified computational model was developed to describe the spray trajectory and the fuel vapor dispersion in the D.I. diesel combustion chamber. The model includes the effects of the breakup on the trajectory and the vaporization of the spray, and the effects of the swirling gas flow and the wall impingement on the dispersion of the fuel vapor.

The purpose of this study was to investigate the effect of residual gas fraction and compositions on the ignition delay of a diesel spray. The air residual gas mixture was produced by injecting diesel sprays into a constant volume combustion bomb with no scavenging burned gas in it. The air initially contained in the bomb was enough to completely burn the fuel supplied by more than 20 injections. The spray injected in the bomb was ignited by the self-ignition process affected by the residual gas. Repetitions of the fuel injection raised the fraction of residual gas in the bomb. The ignition delay in each injection was measured by a photo-transistor. The ignition delay was a minimum when the ambient mixture contained about 4 % residual gas. The effect of residual gas compositions was investigated by adding small amount of CO, CO2 and THC into the bomb. The CO and CO2 compositions in the burned gas produced an elongation of the ignition delay, while the THC shortened the delay period.

Among the alternative fuels, dimethyl ether (DME), one of the oxygenated fuels, attracts attention as an alternative fuel for the Diesel engine since the properties of the DME are fitted to the Diesel engine combustion and the know-how development has been made of the mass production of the DME from a natural gas. In this study, experiments were performed of ignition characteristics of the DME and Diesel fuel sprays injected by a D.I. Diesel injector into a high-pressure, high-temperature vessel. The fuel injection was made by a Bosch type injection system. A schlieren optical system was adopted for visualizing the ignition process as well as the vaporization process of the DME and Diesel fuel sprays. The ignition delay was measured by using a photo-sensor which had a sensitivity in the wavelength range from visible to ultraviolet. Pressure and temperature of the ambient air and the oxygen concentration of the ambient air were changed as experimental parameters.

The ignition and flame propagation processes of a propane-air mixture compounded with a kerosene spray were investigated in order to allow a better understanding of the multi-phase combustion process of the spray compound mixture in a direct injection stratified charge (DISC) engine. The ignition probability and the flame propagation velocity, as functions of the overall equivalence ratio, fraction of propane in the fuel, ignition energy and the Sauter mean diameter of the spray, were measured under atmospheric conditions. The development of the flame kernel and the propagating flame were observed by a high-speed video camera combined with a schlieren system. Adding small amounts of the kerosene spray to the lean propane-air mixture improved the ignition probability. However, the ignition probability depended strongly on the Sauter mean diameter and the ignition energy. Replacing the propane with the kerosene spray in a rich propane-air mixture increased the flame propagation velocity.

A pancake-type constant-volume combustion chamber was used to investigate the combustion and NOx emission characteristics of propane-air and hydrogen-air mixtures under various charge stratification patterns, which were obtained by variations of the initial charge and injected mixture concentrations and the ignition spark timing. A planar laser-induced fluorescence from nitrogen dioxide as gas fuel tracer was applied to measure the mixture distribution in the test chamber. The second harmonic output of pulsed Nd; YAG laser was used as a light source for fluorescence excitation. The fluorescence images were corrected by a gated image-intensified CCD camera. The quantitative analysis of fuel concentration was made possible by the application of linearity between fluorescence intensity and NO2 concentration at low trace level.