Search Results

Seat belts for rear passengers are not commonly used, even though they can significantly reduce fatalities. A passenger seat belt reminder (PSBR) is installed in order to encourage seat belt use, but the effectiveness of PSBRs on the rear seat passenger has not yet been proven. We have developed a methodology to assess PSBR effectiveness. There are two pathways to encourage seat belt use. The first is that PSBR directly facilitates the passenger's use. The second is to motivate the driver request passengers to use seat belts. In the experiment, we asked participants sitting in the driver's seat to select one of five ranks of likelihood to encourage the passenger when a PSBR was presented. We also asked participants sitting in the rear passenger seat to select the rank of likelihood to use the belt voluntarily with PSBR and that to use the belt when the driver requested. The degree of likelihood was quantified by averaging the assigned percentage values to the ranks.

In recent vehicles, E/E architecture is defined and used as a platform to accommodate various electronics features for better development efficiency, lower cost and higher quality. As electronics features increase and integrated control systems make vehicle electronics more complex, good electronics platforms are vital for today's and future vehicle development. This paper first describes the evolution of vehicle electronics and its recent trend and then addresses the challenges facing vehicle electronics: ✓ More integrated control systems ✓ More software ✓ More networks ✓ Shorter time to market Finally, why JasPar1), Japan Automotive Software Platform and Architecture, was founded and how it is organized will be described including the working group activities on FlexRay implementation.

This paper describes a design tool and a software platform for FlexRay systems that are investigated in Nagoya University and are proposed to JasPar. The design tool reads the specification of a system as a task graph that consists of a set of tasks and messages among them. The design tool, then, allocates the tasks to ECUs and schedules the messages on a FlexRay network. The software platform consists of a middleware called time-trigger module (TTM) which dispatches time-triggered tasks, a communication middleware for a time-triggered network (TT-COM), a network management middleware for FlexRay (FlexRay-NM), and a device driver for FlexRay controller.

An investigation based on human visual search functions was conducted into the causative factors of traffic accidents at clear intersections in rural areas. The results indicated that it is difficult for drivers to detect a vehicle traveling on a collision course because the vehicle remains in the same position in the driver's visual field. Two systems are introduced to assist drivers' visual searches. One system uses an image processing technique, and the other utilizes DGPS and IVC techniques. This paper presents the development of the assistance system.

It was found that the finger blood pulse shows various fluctuations in different driving conditions. The nature of the finger blood pulse fluctuations was used for estimating a driver's internal state. Indexes suitable for expressing the fluctuations were moment and density; these indexes were calculated by using a return-map. However these results were measured by an off-line system and were calculated after the experiment. So, an on-line (real-time) system was needed in order to construct a driver's internal state monitoring system. As a first step, an online system for estimating the human internal state was developed. This system is available for estimating the human internal state every 30 seconds.

With the total amount of air pollution caused by vehicle emissions on the increase, the problem has now became a global concern, and various regulatory measures have been put into effect in each region of the world. This is especially true in California, U.S.A, where countermeasures have been adopted early. There, the ULEV (Ultra Low Emission Vehicle) standard, which was ones deemed impossible for gasoline engines to meet, is now in effect. In response to these developments, Honda announced the ULEV system for a 2.2 liter gasoline engine with a closed-coupled catalytic converter (CC) and an under-floor catalytic converter (UF) at the beginning of 1995, and reported on the system's emission characteristics. 1) A new ULEV system has been developed based on the previous system but using only UF, aiming for marketable improvements in product characteristics such as higher output. The new system features the ultra low heat capacity and high heat insulating (ULOC) exhaust manifold.

The goal of this study was to provide information about the frequency of installation and use of fog lamps. Two surveys were performed. In the first one, installation of fog lamps was estimated by a survey of parked vehicles in two iarge shopping centers. The second survey studied the usage of fog lamps during daytime and nighttime, under clear, rainy, or foggy conditions. In this survey, an observer in a moving vehicle noted the types of lamps that were energized on the fronts of oncoming vehicles, and whether fog lamps were installed at all. The main findings are: (1) The best estimate of the current frequency of installation of fog lamps in southeast Michigan is about 13%. (2) During daytime, the usage of fog lamps increased with deterioration in atmospheric conditions, with the usage reaching 50% of all installed fog lamps during moderate-to-heavy fog.