Search Results

A flash evaporation model is being developed to capture the effects of bubble nucleation and growth inside multi-hole injector nozzles to investigate the flash evaporation in fuel injector sprays in Gasoline Direct Injection (GDI). The 1D flash evaporation model is a key tool for providing the 3D Eulerian-Eulerian or Lagrangian spray simulation model with the right droplet size in order to properly predict the effect of degree of superheating on mixture formation. Super heating conditions are likely to be found under partial load conditions in GDI applications or they might be deliberately induced to enhance fuel atomization and vaporization. A quasi-1D nozzle flow model has been developed to help quantifying the effects of main physical and geometrical parameters in promoting fuel flash evaporation. This model is based on an weakly compressible homogenous two-phase mixture assumption. A non-equilibrium model is used to predict the vapour formation rate along the nozzle.

This paper presents a methodology for the 3D CFD simulation of the intake and compression processes of four stroke internal combustion engines.The main feature of this approach is to provide very accurate initial conditions by means of a cost-effective initialization step. Calculations are applied to a low stroke-to-bore SI engine, operated at full load and maximum engine speed. It is demonstrated that initial conditions for this kind of engines have an important influence on flow field development, particularly in terms of mean velocities close to the firing TDC. Simulation results are used to discuss the choice of a set of parameters for the flow field characterization of low stroke-to-bore engines, as well as to provide an insight into the flow patterns during the overlapping period.

The aim of this work is to set up a methodology for simulating Common Rail high-pressure injectors based on coupling a lump-model with CFD two-phase multi-dimensional computations. The unit simulated is the Bosch injector. The injector lump-model resulted in the definition of the three sub-models for hydraulics, mechanics and electro-magnetics. The second-order differential governing equations have been solved in Matlab/Simulink environment and are properly coupled together with the one-dimensional partial differential equations that describe the unsteady pipe flow. A detailed library of thermo-mechanical properties for ISO-4113 oil and diesel fuel is included. Cavitation effects on discharge coefficient in the main orifices were accounted for by using results from CFD steady two-phase flow simulations. The evaluation of the model capability was assessed by using detailed experiments carried out at different practical injector operating conditions.

Upcoming Euro 4 and Euro 5 emission standards are increasing efforts on injection system developments in order to improve mixture quality and combustion efficiency. The target features of advanced injection systems are related to their capability of operating multiple injection with a precise control of the amount of injected fuel, low cycle-by-cycle variability and life drift, within flexible strategies. In order to accomplish this task, injector performance must be optimised by acting on: optimisation of electronic, driving circuit, detailed investigation of different nozzle hole diameter configurations, assessment of the influence of manufacturing errors on hole diameter and inlet rounding on injector performance. The paper will focus on the use of an integrated lump-1D/3D methodology for the design of advanced new fast solenoid Common Rail (C.R.) injector for high speed diesel engines. A lump-model built up in AMESim® environment was used to address the injector design.

This paper deals with a CFD three-dimensional multiphase simulation of rotary vane pump. The paper presents a suitable methodology for the investigation of the cavitation effects and/or incondensable gases. All the 3D simulations were performed by using Fluent v12 (Beta version). A moving mesh methodology was defined to reproduce the change-in-time shape of the internal pump volumes. In particular, the pump analysis was focused on the generation, and evolution of the cavitation phenomena inside the machine to identify the locations where this phenomena could occur. Moreover, the influence of incondensable gas dissolved inside the operator fluid on both pump performance and cavitation evolution was evaluated. Significant results were obtained about the analysis of incondensable gas influence on the cavitation evolution showing that, today, CFD analysis can provide detailed information on such harmful phenomena which can not be achieved by experiments.

The increasing of the overall engine performance requires the investigation of the unsteady engine phenomena affecting intake air flow and the air-fuel mixing process. The “standard” RANS methodology often doesn't allow one to achieve a qualitative and quantitative accurate prediction of these phenomena. The aim of this paper is to show the potential and the limits of LES numerical technique in the simulation of actual IC engine flows and to assess the influence of some basic parameters on the LES simulation results. The paper introduces the use of a merit parameter suggested by Pope for evaluating the quality of the LES solution. The CFD code used is Fluent v6.2 and two basic test cases have been simulated. The first one is the flow over a backward facing step in order to perform a preliminary parametric numerical analysis. A one-equation dynamic subgrid-scales turbulence model is used.

The efficiency of engine operations, i.e. cold start, transient response and operating at idle, depends on the capability of the injection fuel system to promote a homogeneous mixture formation through an efficient interaction with engine fluid dynamics and geometry. The paper presents the development and the application of a methodology for running a CFD PFI engine simulation. A preliminary assessment of the wall-film and droplet-wall interaction sub models has been carried out in order to validate the methodology. Then a three-step numerical procedure has been adopted. The first two steps are aimed to properly initialize the secondary breakup model depending on the type of injector installed on board in order to achieve accurate predictions of spray characteristics.

The optimization of the air-fuel mixture formation plays a very important role in order to reduce the total amount of emissions from an SI engine. To comply with the EURO5 emission restrictions is necessary to understand the influence of injection timing (with respect to engine load) and injector geometry on the air-fuel dynamic interaction. The aim of this paper is to define a CFD methodology for the simulation of a PFI engine. The goals of this analysis are the evaluation of the injector geometry and injection timing influences on the air-fuel mixture preparation and so on the equivalence ratio distribution inside the combustion chamber. Preliminary assessments of the wall-film and droplet-wall interaction sub models have been carried out in order to validate the methodology [1].

An ignition model based on Lagrangian approach was set-up. A lump model for the electrical circuit of the spark plug is used to compute breakdown and glow energy. At the end of shock wave and very first plasma expansion, a spherical kernel is deposited inside the gas flow at spark plug location. A simple model allows one to compute initial flame kernel radius and temperature based on physical mixture properties and spark plug characteristics. The sphere surface of the kernel is discretized by triangular elements which move radially according to a lagrangian approach. Expansion velocity is computed accounting for both heat conduction effect at the highest temperatures and thermodynamic energy balance at relatively lower temperatures. Turbulence effects and thermodynamic properties of the air-fuel mixture are accounted for. Restrikes are possible depending on gas flow velocity and mixture quality at spark location.

In this paper an integrated experimental and numerical approach is applied to optimize a new 2.5l, four valve, turbocharged DI Diesel engine, developed by VM Motori. The study is focused on the EGR system. For this engine, the traditional dynamometer bench tests provided 3-D maps for brake specific fuel consumption and emissions as a function of engine speed and brake mean effective pressure. Particularly, a set of operating conditions has been considered which, according to the present European legislation, are fundamental for emissions. For these conditions, the influence of the amount of EGR has been experimentally evaluated. A computational model for the engine cycle simulation at full load has been built by using the WAVE code. The model has been set up against experiments, since an excellent agreement has been reached for all the relevant thermo-fluid-dynamic parameters. The simulation model has been used to gain a better insight on the EGR system operations.

Today, high performance race car efficiency is based on a very fine equilibrium between aerodynamic efficiency, engine performance, and chassis behaviour. In particular, from the engine point of view, one way to increase the performance is to increase its volumetric efficiency. The aim of this paper is to present the application of the Large Eddy Simulation (LES) approach for the fluid dynamic analysis of a high performance race car airbox geometry. For a naturally aspired engine, the fluid dynamic optimisation of the airbox geometry means to optimise the energy conversion (from dynamic to static pressure) inside the airbox itself, therefore to increase the flow energy on the engine trumpet sections. The LES approach seems to be the best candidate to investigate such a flow since flow unsteadiness are expected to affect airbox efficiency in terms of pressure recovery. The airbox simulations were performed by using the commercial CFD code Fluent v6.3.

The increasing of the overall engine performance requires the investigation of the unsteady engine phenomena affecting intake air flow and the air-fuel mixing process. The “standard” RANS methodology often doesn't allow one to achieve a qualitative and quantitative accurate prediction of these phenomena. The aim of this paper is to show the potential and the limits of LES numerical technique in the simulation of actual IC engine non reactive flows in fixed grids. The paper introduces the use of a merit parameter suggested by Pope for evaluating the quality of the LES turbulence resolution [14]. A basic engine steady flow bench case has been simulated. The CFD code used is Fluent v6.2. The numerical results of a previous LES basic numerical analysis were used for setting up calculations. Large Eddy Simulations using the dynamic one-equation model and a simulation with the WALE sgs model [25] have been performed.

The preparation of the air-fuel mixture represents one of the most critical tasks in the definition of a clean and efficient SI engine. Therefore it becomes necessary to consolidate the numerical methods which are able to describe such a complex physical process. Within this context, the authors developed a CFD methodology into an open-source code to investigate the air-fuel mixture formation process in PFI engines. Attention is focused on moving mesh algorithms, Lagrangian spray modeling and spray-wall interaction modeling. Since moving grids are involved and the mesh quality during motion strongly influences the computed in-cylinder flow-field, a FEM-based automatic mesh motion solver combined with topological changes was adopted to preserve the grid quality in presence of high boundary deformations like the interaction between the piston bowl and the valves during the valve-overlap period.

A second generation of Common-Rail injection systems is coming into production making feasible multiple injection strategies. This paper aims to assess the capability of multiple injection in reducing NOx and soot emissions of HSDI Diesel engines. The analysis has been carried out at a characteristic point of the EUDC emission test cycle by using a customized version of the CFD code Kiva3, with updated sub-models developed by University of Bologna and University of Wisconsin. In particular, a recent modification has been introduced in the fuel conversion rate calculation in order to account for turbulence non-equilibrium effects. Different multiple injection profiles and combustion chamber configurations have been simulated and their effects on mixture formation, heat release rate and NOx and soot formation have been analyzed. The main target was to comply with emission standards without significant loss in engine performance.

The paper investigates the variation of the mass of the fuel injected with respect to nominal conditions in Common Rail injection systems for Diesel automotive applications. Two possible operating conditions have been considered: the consecutive injection of two injectors and the multiple shots of the same injector in the same engine cycle. An integrated experimental and numerical methodology has been used. Several experimental information were available in terms of instantaneous rail and pipe pressure and mass flow rate at different conditions. The 1D numerical model of the whole injection system was useful in addressing the questions remained unresolved in the post-experiments analysis. The experimental results show that injector performances are more related to pressure oscillations in injector connecting pipe rather than inside the common rail.

This paper explores the possibility to extend the low-temperature combustion concept developed for low load conditions to medium load conditions of HSDI DI Diesel engines. The aim is to understand which is the limit of conventional Diesel combustion towards smoke-lees and NOx-less conditions. The present research is based on numerical simulations performed by using the Kiva-3 code updated with physical sub-models. The combined influence of EGR cooling and EGR rate on combustion characteristics and emission formation is analyzed. Then, possible improvements to mixture formation are discussed with particularly emphasis on the use of multiple injection. The calculations show that smoke-less conditions by low-temperature combustion cannot be achieved at medium load and therefore a great role is played by mixture formation.

The Common-rail injection system has allowed achieving a more flexible fuel injection control in DI-diesel engines by permitting a free mapping of the start of injection, injection pressure, rate of injection. All these benefits have been gained by installing this device in combustion chambers born to work with the conventional distributor and in-line-pump injection systems. Their design was aimed to improve air-fuel mixing and therefore they were characterized by the adoption of high-swirl ports and re-entrant bowls. Experiments have shown that the high injection velocities induced by common rail systems determine an enhancement of the air fuel mixing. By contrast, they cause a strong wall impingement too. The present paper aims to exploit a new configuration of the combustion chamber more suited to CR injection systems and characterized by low-swirl ports and larger bowl diameter in order to reduce the wall impingement.

The introduction of high-pressure injection systems in D.I. diesel engines has highlighted already known drawbacks of in-cylinder turbulence modeling. In particular, the well known equilibrium hypothesis is far from being valid even during the compression stroke and moreover during the spray injection and combustion processes when turbulence energy transfer between scales occurs under non-equilibrium conditions. The present paper focuses on modeling in-cylinder engine turbulent flows. Turbulence is accounted for by using the RNG k-ε model which is based on equilibrium turbulence assumptions. By using a modified version of the Kiva-3 code, different mathematically based corrections to the computed macro length scale are proposed in order to account for non-equilibrium effects. These new approaches are applied to a simulation of a recent generation HSDI Diesel engine at both full load and partial load conditions representative of the emission EUDC cycle.

The evaluation of the steady-flow discharge coefficient of ICE port assemble is known to be very sensitive to the capability of the turbulence sub-models in capturing the boundary layer dynamics. Despite the fact that the intrinsically unsteady phenomena related to flow separation claim for LES approach, the present paper aims to demonstrate that RANS simulation can provide reliable design-oriented results by using low-Reynolds cubic k-ε turbulence models. Different engine intake port assemblies and pressure drops have been simulated by using the CFD STAR-CD code and numerical results have been compared versus experiments in terms of both global parameters, i.e. the discharge coefficient, and local parameters, by means of static pressure measurements along the intake port just upstream of the valve seat. Computations have been performed by comparing two turbulence models: Low-Reynolds cubic k-ε and High-Reynolds cubic k-ε.

Injection rate profile is a powerful tool to control engine performance and emission levels. In particular, the Common Rail (C.R.) injection system has allowed flexible fuel injection in DI-diesel engines by permitting a free mapping of the start of injection, injection pressure, rate of injection and, in the near future, multiple injections,. This paper deals with improvements of stable operating condition limits of the Common Rail injector for multiple injection purposes. The focus was to optimize the behavior of the solenoid valve in order to reduce the minimum time interval between two consecutive injections required for system stability. An extensive experimental characterization of the valve has been performed in order to measure the main mechanical and electrical parameters of the assembly components. The experimental and the numerical studies have allowed optimizing the current profile and consequently the design of the anchor pin-ring assembly of the solenoid valve.