Search Results

There is a growing interest in improving engine versatility through the capacity to run on more than one fuel. To aid in this effort, the research presented in this paper investigated a novel system using microwave plasma ignition designed with the goal of allowing standard gasoline engines to run on non-standard fuels. The fuel used was Jet A. The test engine was a Briggs and Stratton single cylinder engine outfitted with an aftermarket fuel injection system and the microwave plasma ignition system. The tests performed were to determine the cold-start temperature limit, the lowest temperature at which the engine could be repeatedly started, using microwave plasma ignition with a conventional spark plug as a reference. A detailed system outline is presented, as well as results and conclusions. Recommendations for further research are also suggested.

Significant environmental and economic benefit could be obtained if spark ignited (SI) engines could be made more efficient. Engine operation using leaner fuel air mixtures at higher power densities and pressures promise higher thermal efficiencies. Mixtures required for such operation are often difficult to ignite with traditional spark plugs. In pursuit of better ignition sources, this paper presents a high-level model of an alternative microwave plasma ignition source under development. In this publication, atmospheric measurements of a pulsed microwave ignitor are used to derive an empirical model that will allow for control and increased energy delivery to the device. The model accounts for a simplistic plasma formation delay, a drop in resonance frequency as a result of plasma formation, and a subsequent change in associated microwave reflection coefficient.

Circulation control technologies have been applied to fixed wing aircraft for approximately four decades. During those early tests an increase in lift coefficient of nearly four times the unaltered airfoil was achieved. Applying these or similar technologies, particularly inducing the coanda effect through blowing slots to rotorcraft blades, can enhance the performance of the helicopter. The increase in lift coefficient of the rotor blade provides more options to the designer, including decreasing the rotor diameter, decreasing the rotor speed, increasing the payload capacity, or a combination of all three. By either reducing the diameter and/or the rotor speed the blade tip speed can be reduced, thus allowing a higher forward flight speed. Retreating blade stall can also be reduced by applying circulation control to the leading edge of the rotor blade.

Current research has involved manipulating the ignition inside of the combustion chamber. It has been demonstrated that an RF plasma flame can be generated from microwaves in a Quarter Wave Coaxial Cavity Resonator (QWCCR). By using this method, it may become possible for researchers to improve combustion and ignition characteristics of a modern internal combustion engine. Filling a plasma cavity with an appropriate dielectric medium can both alter electromagnetic properties and provide a suitable protective barrier to the harsh condition inside of a combustion cylinder. It is the purpose of this paper is to investigate both the operating frequency and quality factor of dielectric-filled cavities, as well as to suggest dielectrics that would be suitable for such an application.

Over the years, there have been different ways to reduce glare from mirrors for drivers - dimmable electrochromic mirrors being the latest option. These mirrors often have a limited lifespan when exposed to the environment, and are often costly to replace. It is now feasible to have a rear-view mirror assembly whose reflectance is mechanically adjustable. This is accomplished by using polarized light and a pair of specially constructed polarizers. These polarizers attenuate light by sliding past one another in a linear fashion, as opposed to rotating with respect to one another to cross their transmission axes. This is ideal for rear-view mirrors whose shapes are often oblong and rotation of a polarizer is awkward. In the event of a power failure, these polarizing mirrors are still capable of dimming. They can be made to function well in both hot and cold environments, have a long lifespan, and are inexpensive when compared to electrochromic mirrors.

The Federal Test Procedure (FTP) for heavy-duty engines requires the use of a full-flow tunnel based constant volume sampler (CVS). These are costly to build and maintain, and require a large workspace. A small portable micro-dilution system that could be used on-board, for measuring emissions of in-use, heavy-duty vehicles would be an inexpensive alternative. This paper presents the rationale behind the design of such a portable particulate matter measuring system. The presented micro-dilution tunnel operates on the same principle as a full-flow tunnel, however given the reduced size dilution ratios can be more easily controlled with the micro dilution system. The design targets dilution ratios of at least four to one, in accordance with the ISO 8178 requirements. The unique features of the micro-dilution system are the use of only a single pump and a porous sintered stainless steel tube for mixing dilution air and raw exhaust sample.

The Federal Test Procedure (FTP) for heavy-duty engines requires the use of a full-flow tunnel based constant volume sampler (CVS) which is costly to build and maintain, and requires a large workspace. A portable micro-dilution system that could be used for measuring on-board, in use emissions from heavy duty vehicles would be an inexpensive alternative compared to a full-flow CVS tunnel, as well as requiring significantly less workspace. This paper evaluates such a portable particulate matter measuring system. This micro-dilution tunnel operates on the same principle as a full-flow tunnel, however dilution ratios can be more easily controlled with the micro dilution system. The dilution ratios for the micro-dilution system were maintained at least four to one, as per ISO 8178 requirements, by measuring the mass flow rates of the dilution air and dilute exhaust.

When designing the Oculus sensor platform, many safety issues such as designing fail safes, adapting to flying situations, and examining situations produced by exposure to real-world conditions were taken into consideration. When predicting maintenance issues, environmental conditions that the platform will have to encounter were assessed. A material that was lightweight and strong enough to withstand the harsh environmental conditions experienced outside the C-130 aircraft was needed. In addition to the material used, another issue addressed was the ability to repair the platform easily and efficiently. Normal operations expose the components to significant wear and tear, which requires the replacement of parts to maintain safe operations. Oculus was constructed to allow for component replacement without deconstruction of the entire platform. While environmental factors were a concern, mechanical design and functionality, along with safety, was vital to the project.

Project Oculus, an experimental configurable sensor platform for deploying airborne sensors on a C-130 aircraft, is currently in its pre-flight testing phase. The electronics driving the platform are available commercially off the shelf (COTS) and as such are not automatically rated to comply with stringent military electromagnetic standards as defined in MIL-STD-461. These COTS electronics include efficient switching power converters, variable frequency motor drives (VFD), and microprocessor based equipment, all of which can present electromagnetic interference (EMI) issues. Even in a design where EMI issues were not considered up front, it is often possible to bring the overall configuration into compliance. Switching and digital clock signals produce both conducted and radiated noise emissions. Long cable runs and enclosure apertures become noise transmitting antennas. Large switching currents place noise on the power lines causing interference with other equipment.

It has been proposed that an automated remote color inspection of automobile body panels is possible with a reasonably precise color measurement. This paper outlines a test of a new 3D color measurement technology as applied to this task and presents the results of the first test. A camera is set up several feet away from a car body; a 3D orientation measuring system takes both 3D and color data from the car. The raw data is presented as a set of 3D graphs; the geometry-corrected data is also provided. Statistical analysis is presented to indicate system precision.