Search Results

The lightweighting potential brought by advanced high strength steels (AHSS) was studied on automotive exterior panels. The dent resistance was selected as a measure to quantify the lightweighting since it is the most crucial for exterior panels. NEXMET® 440EX and 490EX, which possess both the surface quality and high strength, are evaluated and compared with BH210 and BH240. The denting analysis was conducted first on representative plates with different curvatures to simulate the dented areas on door outer, roof and hood panels. In addition, both 1% and 2% pre-strain and baking scenarios are considered for this plate, which represent the most common situations for exterior panels. The maximal dent load that the plates can sustain was calculated and compared for all those steel grades. Then the dent resistance analysis was conducted on a selected door outer panel. The minimum gauge required to meet the dent resistance performance was obtained.

To help predict the injury responses of child pedestrians and occupants in traffic incidents, finite element (FE) modeling has become a common research tool. Until now, there was no whole-body FE model for 10-year-old (10 YO) children. This paper introduces the development of two 10 YO whole-body pediatric FE models (named CHARM-10) with a standing posture to represent a pedestrian and a seated posture to represent an occupant with sufficient anatomic details. The geometric data was obtained from medical images and the key dimensions were compared to literature data. Component-level sub-models were built and validated against experimental results of post mortem human subjects (PMHS). Most of these studies have been mostly published previously and briefly summarized in this paper. For the current study, focus was put on the late stage model development.

This paper represents the development of a new design methodology based on data mining theory for decision making in vehicle crashworthy components (or parts) development. The new methodology allows exploring the big crash simulation dataset to discover the underlying complicated relationships between vehicle crash responses and design variables at multi-levels, and deriving design rules based on the whole vehicle safety requirements to make decisions towards the component and sub-component level design. The method to be developed will resolve the issue of existing design approaches for vehicle crashworthiness, i.e. limited information exploring capability from big datasets, which may hamper the decision making and lead to a nonoptimal design. A preliminary design case study is presented to demonstrate the performance of the new method. This method will have direct impacts on improving vehicle safety design and can readily be applied to other complex systems.

Numerical models of Hybrid III had been widely used to study the effect of underbody blast loading on lower extremities. These models had been primarily validated for automotive loading conditions of shorter magnitude in longer time span which are different than typical blast loading conditions of higher magnitude of shorter duration. Therefore, additional strain rate dependent material models were used to validate lower extremity of LSTC Hybrid III model for such loading conditions. Current study focuses on analyzing the mitigating effect of combat boots in injury responses with the help of validated LSTC Hybrid III model. Numerical simulations were run for various impactor speeds using validated LSTC Hybrid III model without any boot (bare foot) and with combat boot.

Spring-back phenomena are critical in stamping procedures for advanced high strength steel. An analytical model is developed to predict the spring-back effect for a U-channel part with post-stretching process. The stress distribution is obtained by direct application of material constitutive relationship. The subjected loading conditions are sequentially bending, (un-bending), and uniform stretching, based on different zones in the part. Both the loading history and the friction effects are considered in the model. The bending moments are obtained to generate a theoretical spring-back shape. Great performance in spring-back control is achieved by applying certain high level of external forces. FE simulation is conducted for the identical stamping process with post-stretching. Good correlation is observed between the analytical and numerical solutions/experimental results under various scenarios.

Dimensional accuracy of punched hole is an essential consideration for high-quality sheet metal forming. An out-of-shape hole can give rise to manufacturing issues in the subsequent production processes thus inducing quality defects on a vehicle body. To understand the effects of punch shapes and cutting configurations on punched hole diameter deviations, a systematical experimental study was conducted for multiple types of AHSS (DP1180, DP980, DP590) and one mild steel. Flat, conical and rooftop punches were tested respectively with three cutting clearances on each material. The measurement results indicated different diameter enlargement modes based on the punch profiles, and dimensional discrepancies were found to be more significant with the stronger materials and higher cutting clearance. To uncover the mechanism of punched hole enlargement, a series of finite element simulations were established for numerical investigation.

The elevated strength of advanced high strength steels (AHSS) leads to enormous challenges for the sheet metal processing, one of which is hole punching operation. The total tonnage must be estimated at each trimming stage to ensure successful cutting and protect the press machine. This paper presents the effects of hole punch configurations on the punching force with the consideration of punch shape, cutting clearance and material grade. The hole punching experiments were performed with DP590, DP980, DP1180 and one mild steel as a reference. The punching force coefficient is defined and presents a negative correlation with the material strength based on the experimental data. Surface quality was examined to analyze the damage accumulation during the punching process. The cutting mechanisms with various punch shapes were revealed through an extensive finite element simulation study.

Twist spring-back would interfere with stamping or assembling procedures for advanced high strength steel. A “homeopathic” resolution for controlling the twist spring-back is proposed using unbalanced post-stretching configuration. Finite element forming simulation is applied to evaluate and compare the performance for each set of unbalanced post-stretching setup. The post-stretching is effectuated by stake bead application. The beads are separated into multiple independent segments, the height and radii of which can be adjusted individually and asymmetrically. Simulation results indicate that the twist spring-back can be effectively controlled by reducing the post-stretching proximate to the asymmetric part area. Its mechanism is qualitatively revealed by stress analyses, that an additional but acceptable cross-sectional spring-back re-balances the sprung asymmetrical geometry to counter the twist effect.

The use of cyclic corrosion tests which consist of salt spraying, humidifying, and drying phases is desirable in the evaluation of the corrosion performance of automotive body panels. In this work, coupons of zinc-coated steel and of cold rolled steel were exposed to a defined cyclic corrosion test (CCT) which has shown to be suitable for simulating diverse outdoor conditions for evaluating the cosmetic corrosion of precoated steel. Micro-environment data in the gap of lapped panel specimens, such as wetness, corrosion rate of test materials, pH value, chloride content, have been obtained during the CCT test. The galvanic current flowing between a gold electrode and the test materials was measured to monitor the degree of wetness inside the crevice. The results show that the surface of the test materials never became really dry even during the dry period of the CCT cycle. Furthermore, the wetness during wet and dry periods in the crevice increased with increasing number of CCT cycle.

Lithium-ion (or Li-ion) battery systems are being increasingly used as the main power source in new generation hybrid and electric vehicles. Their mechanical integrity under abuse loading conditions is very important for vehicle safety design. In this research, a computational study was performed to simulate mechanical tests on vehicle battery cells and modules. The tests were conducted on commercial Li-ion battery cells and entire modules at low speed using a high capacity material testing system. Based on loading and boundary conditions during the tests, finite element (FE) models using the explicit FEA solver LS-DYNA, were developed. The model predictions demonstrated reasonable agreement in terms of failure modes and force-displace response at both cell and module levels.

The rooftop punch is proposed to reduce the maximum cutting force during the trimming operation for advanced high strength steels (AHSS), by introducing a shearing angle at the tool edge. However, such non-simultaneous shearing mechanism results in the inconsistent deformation around the hole perimeter, and consequently affects the dimensional accuracy of the trimmed hole. A numerical study was conducted to investigate the effects of punch tipping angle and tipping heights on the force reduction and dimensional discrepancies. The 60mm hole punching operation for DP 1180 (1.2mm) material was simulated with finite element analysis. The tipping height was reduced by introducing flat portions to the rooftop punch and it can mitigate the material deformation difference before trimming. The results showed tipping height played a significant role of dimensional accuracy control by adopting small tipping angle and broad flat portions.

Due to the variation of compartment design and occupant’s posture in self-driving cars, there is a new and major challenge for occupant protection. In particular, the studies on occupant restraint systems used in the self-driving car have been significantly delayed compared to the development of the autonomous technologies. In this paper, a numerical study was conducted to investigate the effectiveness of three typical restraint systems on the driver protection in three different scenarios.

Cellular solids are excellent energy absorbers and widely applied in the automotive passive safety area. Their microstructures offer the ability to undergo large plastic deformation at nearly constant nominal stress and thus can absorb a large amount of kinetic energy before collapsing to a more stable configuration or fracture. To further improve their performance, it is imperative to develop a systematic design method, to tailor microstructures’ behavior by adjusting their geometric parameters, especially for those with irregular, random shapes. In this research, we proposed a machine learning based method, which combines the finite element (FE) analysis to design open cell foams for crash energy absorption. The foam geometry is generated utilizing a large number of core points and convex polygons, known as the Voronoi diagram, and then converted to the FE model to compute the plateau stress under crush loading.

Lithium-ion batteries (LIBs) have been used as the main power source for Electric vehicles (EVs) in recent years. The mechanical behavior of LIBs subject to crush loading is crucial in assessing and improving the impact safety of battery systems and EVs. In this work, a detailed 3D finite element model for a commercial vehicle battery was built, in order to better understand battery failure behavior under various loading conditions. The model included the major components of a prismatic battery jellyroll, i.e., cathodes, anodes, and separators. The models for these components were validated against the corresponding material coupon tests (e.g., tension and compression). Then the components were integrated into the cell level model for simulation of jellyroll loading and damage behavior under three types of compressive indenter loading: (1) Flat-end punch, (2) Hemispherical punch and (3) Round-edge wedge. The comparisons showed reasonable agreement between modeling and experiments.

As early as the 1950's, Gurdjian and colleagues (Gurdjian et al., 1955) observed that brain injuries could occur by direct pressure loading without any global head accelerations. This pressure-induced injury mechanism was "forgotten" for some time and is being rekindled due to the many mild traumatic brain injuries attributed to blast overpressure. The aim of the current study was to develop a finite element (FE) model to predict the biomechanical response of rat brain under a shock tube environment. The rat head model, including more than 530,000 hexahedral elements with a typical element size of 100 to 300 microns was developed based on a previous rat brain model for simulating a blunt controlled cortical impact. An FE model, which represents gas flow in a 0.305-m diameter shock tube, was formulated to provide input (incident) blast overpressures to the rat model. It used an Eulerian approach and the predicted pressures were verified with experimental data.

Anthropometric test devices (ATDs), such as the Hybrid III crash-test dummy, have been used to simulate lower-extremity responses to military personnel subjected to loading conditions from anti-vehicular (AV) landmine blasts. Numerical simulations [e.g., finite element (FE) analysis] of such high-speed vertical loading on ATD parts require accurate material parameters that are dependent on strain rate. This study presents a combined experimental and computational study to calibrate the rate-dependent properties of three materials on the lower extremities of the Hybrid III dummy. The three materials are heel-pad foam, foot skin, and lower-leg flesh, and each has properties that can affect simulation results of forces and moments transferred to the lower extremities.

A new design methodology based on data mining theory has been proposed and used in the vehicle crashworthiness design. The method allows exploring the big dataset of crash simulations to discover the underlying complicated relationships between response and design variables, and derive design rules based on the structural response to make decisions towards the component design. An S-shaped beam is used as an example to demonstrate the performance of this method. A large amount of simulations are conducted and the results form a big dataset. The dataset is then mined to build a decision tree. Based on the decision tree, the interrelationship among the geometric design variables are revealed, and then the design rules are derived to produce the design cases with good energy absorbing capacity. The accuracy of this method is verified by comparing the data mining model prediction and simulation data.

Lithium-ion battery systems have been used as the main power source for electric vehicles due to their lightweight and high energy density. The impact safety of these battery systems has been a primary issue. In this work, the crashworthiness design of a typical vehicle battery module is implemented through numerical (finite element) simulations integrated with machine learning algorithms (decision trees). The module with multiple layered porous cells is modeled with a simplified, homogeneous material law, and subjects to the impact of a cylindrical indenter. The main protective component on the module - cover plate is designed as an energy absorbing sandwich structure with a core of cellular solids. Large scale simulations are conducted with various design variable values for the sandwich structure, and the results form a design (simulation) dataset.

Lithium-ion (Li-ion) batteries are considered as one of the solutions for electric vehicles (EV) in the automotive industry due to their lightweight and high energy density. Their mechanical performance is of great importance for EV crashworthiness design. In this study, quasi-static and dynamic indentation tests were conducted on commercially available vehicle battery pouch cells to investigate their structural integrity. Three indenters, namely, a 19.1 mm (3/4 in.) diameter flat end (FE), a 25.4 mm (1 in.) diameter hemispherical (LH), and a 12.7 mm (1/2 in.) diameter hemispherical (SH), were used to investigate the punch force-deflection responses of the cells. Loading velocity varied in the range of 0.06 mm/s to 3 m/s to test the strain rate effect. Simplified closed-form analysis solutions were developed to predict the pouch cell force-deflection response by considering the effect of compression, tension, and shear of the battery component materials.

Multiple hybrid bead designs were investigated in this study to control the springback on DP780 samples using post-stretching technique. The performance of the four different hybrid bead designs was evaluated by measuring the minimum blank-lock tonnage required to control the springback during a U-channel stamping process. A finite element (FE) model of the U-channel stamping process was developed to simulate the process and predict the minimum blank-lock tonnage required for springback control using each of the hybrid bead designs. It is shown that the developed FE model predicts both the required minimum blank-lock tonnage for post-stretching, and the springback profile, with good accuracy.