Search Results

Different optimization strategies for the optimization of the calibration of a turbocharged GDI engine through numerical simulation were analyzed, aiming to evaluate the opportunities offered by direct optimization techniques. A one-dimensional fluid dynamic engine model was used to predict engine performance, taking into account knock and exhaust temperature constraints. Air fuel ratio, spark advance, boost pressure and cam phasing were optimized by means of different optimization strategies, including direct search as well as numerical methods. Both full load (with maximum bmep targets) and part load (with minimum bsfc targets) were considered.

Different hybrid powertrains for a European mid-size passenger car were evaluated in this paper through numerical simulation. Different degrees of hybridizations, from micro to mild hybrids, and different architectures and power sources management strategies were taken into account, in order to obtain a preliminary assessment of the potentialities of different hybrid systems for the European passenger car market. Both diesel and gasoline internal combustion engines were considered: a 1.6 dm₃ Common Rail turbocharged diesel, and a 1.4 dm₃ spark ignition turbocharged engine, equipped with an innovative Variable Valve Actuation system. Diesel hybrid powertrains, although being subject to NOx emissions constraints that could jeopardize their benefits, offered substantial advantages in comparison with gasoline hybrid powertrains. Potentialities for fuel consumption reductions up to 25% over the NEDC were highlighted, approaching the 2020 EU 95 g/km CO₂ target.

Fuel consumption and NOx emissions of different Diesel-Electric hybrid powertrains, equipping a midsize European passenger car were evaluated in this paper through numerical simulation. Different degrees of hybridizations, from micro to mild hybrids, and different architectures and power sources management strategies were taken into account, in order to obtain a preliminary assessment of the potentialities of a Diesel-Electric hybrid system for the European passenger car market. Both regulated driving cycles, such as NEDC, and “real-world representative” driving cycles, such as Artemis cycles, were evaluated, in order to obtain not only an estimate of the impact of hybridization on type-approval CO2 and NOx emissions, but also an assessment of the impact of these technologies from the vehicle owner's perspective. Finally, the effects of internal combustion engine downsizing was also considered.

The loading of a DPF entails the need of trap regeneration by particulate combustion, whose efficiency and frequency are somehow affected by the way soot is deposited along the channels. The aim of this work is therefore the development of a new experimental methodology able to provide fundamental information about the soot loading process inside the DPF, in order to take advantage of this insight for DPF design and optimization purposes. Small lab-scale 300 cpsi DPF samples were loaded downstream of the DOC in an ad hoc designed reactor capable of hosting 5 samples, by diverting part of the entire flow produced by an automotive diesel engine at 2500 rpm × 8 BMEP, selected as representative of the most critical operating conditions for soot production during the New European Driving Cycle (NEDC).

Different EGR system layouts (a Long Route, a Short Route, and a combination of the two) were evaluated by means of both numerical simulation and experimental tests. In particular, a one-dimensional fluid-dynamic engine model was built in order to evaluate the potential of a Long Route EGR system as well as the potential of different EGR combinations between Long and Short Route. By means of the one-dimensional model, used as a virtual test bench, the estimations of the NOx emissions, based on the Extended Zeldovich Mechanism (EZM), for the different solutions, were compared and valuable information for the calibration of the coordinated EGR LR, EGR SR and Variable Geometry Turbine (VGT) control systems was obtained.

Different diagnostic techniques were experimentally tested on a common rail automotive 4 cylinder diesel engine in order to evaluate their capabilities to fulfill the California Air Resources Board (CARB) requirements concerning the monitoring of fuel injected quantity and timing. First, a comprehensive investigation on the sensitivity of pollutant emissions to fuel injection quantity and timing variations was carried out over 9 different engine operating points, representative of the FTP75 driving cycle: fuel injected quantity and injection timing were varied on a single cylinder at a time, until OBD thresholds were exceeded, while monitoring engine emissions, in-cylinder pressures and instantaneous crankshaft revolution speed.

In this study, a new EGR control technique, based on the estimate of the oxygen concentration in the intake manifold, was firstly investigated through numerical simulation and then experimentally tested, both under steady state and transient conditions. The robustness of the new control technique was also tested and compared with that of the conventional EGR control technique by means of both numerical simulation and experimental tests. Substantial reductions of the NOx emissions under transient operating conditions were achieved, and useful knowledge for controlling the EGR flow rate more accurately was obtained.

Experimental Design methodologies have been applied in conjunction with objective functions for the optimization of the internal geometry of a rear muffler of a subcompact car equipped with a 1.4 liters displacement s.i. turbocharged engine. The muffler also features an innovative variable geometry design. The definition of an objective function summarising the silencing capability of the muffler has been driving the optimization process with the aim to reduce the tailpipe noise while maintaining acceptable pressure losses and complying with severe space constraints. Design of Experiments techniques for the reduction of experimental plans have been shown to be extremely effective to find out the optimum values of the design parameters, allowing a remarkable reduction of the time required by the design process in comparison with full factorial designs.

Although the use of Exhaust Gas Recirculation (EGR) is nowadays mandatory for automotive diesel engines to achieve NOx emissions levels complying with more and more stringent legislation requirements, electronically controlled EGR systems still represent an expensive technology, often unsuitable for small diesel engines for off-road applications or for two/three wheelers. An interesting option for these categories of small diesel engines is the so-called “internal EGR”, which is obtained by modifying the intake or the exhaust valve lift profile, in order to increase the fraction of exhaust residuals at the end of the intake stroke. Different valve lift profiles were therefore evaluated for a 2 cylinders, 700 cc, Lombardini IDI diesel engine, equipping a light 4 wheelers vehicle.

A DoE analysis was carried out to investigate the effects of the compression ratio, injection timing, injector nozzle hole size and number on performance and emissions in a diesel marine engine, aiming to find out the optimal combination between all the abovementioned parameters. The study was performed on a six cylinder in line, 100 liter total displacement, diesel marine engine, by means of a 1-D engine simulation fluid-dynamic code, coupled with a multi-zone combustion model for oxide of nitrogen (NOx) and particulate (PM) prediction. A preliminary detailed validation process, based on an extensive experimental data set, was carried out on the engine model concerning, in particular, the predicted heat release rate, the in-cylinder pressure trace and NOx emissions for several operating points of a propeller load curve.

A new mean value engine model was developed in order to investigate the dynamic performance of vehicles equipped with turbocharged diesel engines, especially as far as the acceleration transients are concerned, where the turbolag phenomenon plays a major role. The turbocharger was modeled through the mass flow and efficiency maps which are usually provided by the manufacturer, with additional extrapolation routines for the map area in the low compression/expansion ratio region, which is particularly important for tip-in manoeuvres simulation. For the internal combustion engine modeling, experimentally derived maps of indicated efficiency, volumetric efficiency and exhaust gas temperature as a function of engine speed and load were used. Finally, a mass balance in the intake and exhaust manifolds was carried out with a filling and emptying technique.

The potential of an electric assisted turbocharger for a heavy-duty diesel engine has been analyzed in this work, in order to evaluate the turbo-lag reductions and the fuel consumption savings that could be obtained in an urban bus for different operating conditions. The aim of the research project was to replace the current variable geometry turbine with a fixed geometry turbine, connecting an electric machine which can be operated both as an electric motor and as an electric generator to the turbo shaft. The electric motor can be used to speed up the turbocharger during the acceleration transients and reduce the turbo-lag, while the generator can be used to recover the excess exhaust energy when the engine is operated near the rated speed, in order to produce electrical power that can be used to drive engine auxiliaries. In this way the engine efficiency can be improved and a kind of “electric turbocompounding” can be obtained.

The effect of variations of compression ratio (CR) and injection pressure (IP) on the emissions and performance of a small displacement common rail off-road diesel engine was evaluated. The operating point corresponding to the 5th mode of the ISO 8178 - C1 test cycle (intermediate speed / full load) was considered, since it represents one of the most critical operating conditions as far as exhaust emissions are concerned. The main effect of a reduction of the compression ratio, for a fixed injection timing, was found to be, as expected, an increase in NOx emissions along with a decrease of PM emissions, with a substantial redefinition of the PM-NOx trade-off curve; the choice of a proper value for the start of injection can therefore lead to a better compromise among pollutant emissions, although remarkable variations in BSFC and combustion noise must be taken into account.

The potential of dual stage turbocharging and Miller Cycle for a six cylinders in line, 13 litres displacement, HD diesel engine was analysed in this work, by means of a 1-D engine simulation fluid dynamic code, coupled with a multi-zone combustion model for NOx and PM prediction. After a detailed validation process, based on an extensive experimental data set, the engine model was then used to predict the effects on engine performance and emission characteristics of different combinations of dual stage turbochargers, engine compression ratio values and intake valve lift profiles. The potential for an appreciable increase in the engine power, with a slight decrease in the specific fuel consumption and a remarkable decrease of NOx specific emissions was demonstrated.

In this work the formation and the evolution of the fuel spray emerging from a hollow-cone swirl injector were investigated. The first aim of the work was to set up a tool for fuel spray simulation in a CFD analysis that can offer a reasonable accuracy with no significant increment in the computational time. The analysis started from a theoretical formulation of the fuel flow inside the injector, based on the potential theory, obtaining an injector model which allows the calculation of the main spray characteristics usually required by the CFD analysis (i.e. droplet velocity, fuel film thickness, droplet size distribution). These parameters can be obtained only from spray cone angle and mass flow rate, which are the data commonly provided by injector manufacturers. Furthermore, a phenomenological approach was also presented, in order to properly simulate in CFD analysis the spray tip penetration in the dense spray zone, without requiring an increase of the spatial grid resolution.

Design of Experiments (DoE) methodologies have been applied in conjunction with objective functions to the experimental optimization of multiple injection strategies for a small displacement Common Rail (CR) off-road diesel engine. One operating point, which corresponds to the 5th mode of the ISO 8178 - C1 test cycle (intermediate speed / full load), was considered during this analysis: this operating condition is one of the most critical as far as exhaust emissions for the considered engine are concerned. Three injections were actuated per engine cycle during the experimental tests, with different strategies characterized by different timings and durations of each injection. It was found that DoE techniques for the reduction of experimental plans can be very effective in finding the optimum values for the injection parameters, leading to a remarkable reduction in the calibration process time, compared to full factorial designs.

Numerical simulation can be effectively used to reduce the experimental tests which are nowadays required for the analysis and calibration of engine control and diagnostic systems. In particular in this paper the use of a one-dimensional fluid-dynamic engine model of an 8 cylinders high-performance s.i. engine coupled with a vehicle and driveline model to simulate the effects of misfire events on the engine angular speed is described. Furthermore, the effect of cycle-to-cycle combustion variability was also evaluated, in order to take into account variations in the combustion process that can substantially increase the engine speed fluctuations under normal operating conditions, thus hindering the misfire detection. Finally, a comparison with experimental data obtained on a chassis dynamometer was carried out. After this accuracy assessment, the numerical simulation could be used to analyze different techniques for misfire detection, thus reducing the required experimental tests.

The unsteady flow effects in two different close coupled catalytic converters were investigated in order to achieve a better understanding of the steady state experimental tests which are usually performed to evaluate a flow distribution. Firstly the validity of a CFD model was achieved through a comparison of some steady state simulations with the results of HWA experimental measurements. Several different formulations of the uniformity index, that were found in literature, were then compared, trying to highlight the strengths and shortcomings of each one. Further information was derived from a comparison of the two catalysts that were tested to achieve a general methodology that would be useful for future analysis. Finally, a new approach to evaluate the flow distribution using a steady state analysis was proposed by comparing the results of a transient simulation that was obtained for a whole engine cycle.

The potential of numerical simulation in the analysis of the dynamic transient response of a vehicle during tip-in manoeuvres has been evaluated. The dynamic behavior of the driveline of a typical European gasoline car was analyzed under a sharp throttle input. A one-dimensional fluid dynamic model of the engine was realized for the simulation of the input torque; afterwards, it was coupled with a driveline and vehicle model implemented in Matlab-Simulink environment. After a detailed validation process based on several sets of experimental data, the engine and vehicle coupled simulation was used to evaluate different control strategies during tip-in manoeuvres aiming to enhance the vehicle driveability.

The influence of different multiple injection strategies on the emissions, combustion noise and BSFC (brake specific fuel consumption) of a small non-road diesel engine prototype equipped with a Common Rail (CR) fuel injection system has been analysed. The two most critical operating points according to the ISO 8178 - C1 test cycle as far as the exhaust emissions are concerned (Intermediate Speed/Full Load; Rated Speed/Full Load) were considered. Different injection strategies, each with a fixed number of consecutive injections (up to 4), were tested for the selected operating points. It was found that multiple injection strategies can be very effective also for small displacement non-road diesel engines in reducing particulate matter (PM), NOx and noise levels without increasing fuel consumption.