Search Results

The effects of operating parameters (speed, load, spark-timing, EGR, and end of fuel injection timing [EOI]) on engine-out, regulated (total HC, NOx, and CO) and speciated HC emissions have been investigated for a 1.83 L direct-injection, spark-ignition (DISI) engine. As the EOI is varied over the range from high to low stratification with other engine parameters held constant, the mole fractions of all regulated emissions vary sharply over relatively small (10-20 crank angle degrees [CAD]) changes in EOI, suggesting that emissions are very sensitive to the evaporation, mixing, and motion of the stratified fuel cloud prior to ignition. The contribution of unburned fuel to the HC emissions decreases while the olefinic partial oxidation products increase as the fuel stratification increases, increasing the smog reactivity of the HC in the exhaust gas by 25%.

The numbers, sizes, and derived mass emissions of particles from a production DISI engine are examined over a range of engine operating conditions. Particles are sampled directly from the exhaust pipe using heated ejector pump diluters. The size distributions are measured using a scanning mobility particle sizer. The numbers and sizes of the emitted particles are reported for stratified versus homogeneous operation and as a function of fuel injection timing, spark timing, engine speed, and engine load. The principal finding is that particle number emissions increase by about a factor of 10 - 40 going from homogeneous to stratified charge operation. The particulate emissions exhibit a strong sensitivity to injection timing; generally particle number and volume concentrations increase steeply as the injection timing is retarded, except over a narrow portion of the range where the trend reverses.

A study to investigate the influence of fuel injection timing on exhaust emissions from a single-cylinder direct-injection spark-ignition (DISI) research engine was performed. Experimental results were obtained for carbon monoxide (CO), unburned hydrocarbon (HC), and oxides of nitrogen (NOx). Images showing the variation of liquid-phase fuel distribution with changing injection timing were obtained in a firing optically-accessed engine of similar design. A correlation between measured emissions and observed liquid-phase fuel distribution was performed. This correlation was supported by development of phenomenological models that permit explanation of the variation of CO, HC, and NOx emissions with changes in air-fuel mixture preparation.

Data from two engines with distinct stratified-charge combustion systems are presented. One uses an air-forced injection system with a bowl-in-piston combustion chamber. The other is a liquid-only, high-pressure injection system which uses fluid dynamics coupled with a shaped piston to achieve stratification. The fuel economy and emission characteristics were very similar despite significant hardware differences. The contributions of indicated thermal efficiency, mechanical friction, and pumping work to fuel economy are investigated to elucidate where the efficiency gains exist and in which categories further improvements are possible. Emissions patterns and combustion phasing characteristics of stratified-charge combustion are also discussed.

Current demands for high fuel efficiency and low emissions in automotive powerplants have drawn attention to the two-stroke engine configuration. The present study measured trapping and scavenging efficiencies of a firing two-stroke spark-ignition engine by in-cylinder gas composition analysis. Intermediate results of the procedure included the trapped air-fuel ratio and residual exhaust gas fraction. Samples, acquired with a fast-acting electromagnetic valve installed in the cylinder head, were taken of the unburned mixture without fuel injection and of the burned gases prior to exhaust port opening, at engine speeds of 1000 to 3000 rpm and at 10 to 100% of full load. A semi-empirical, zero-dimensional scavenging model was developed based on modification of the non-isothermal, perfect-mixing model. Comparison to the experimental data shows good agreement.

The fiber optic spark plug was used in conjunction with a piezoelectric pressure transducer to collect combustion diagnostic data on four production engines designed to generate quiescent, swirl, and tumble charge motions. Spark advance was varied under low speed, low load conditions to investigate changes in flame kernel behavior and in-cylinder charge motion as functions of crank angle and spark advance. Two flame kernel models were filled to the data and a critical comparison of the models was conducted. Flame kernel behavior was represented by three values: convection velocity, growth rate, and convection direction. Convection velocity was highest in the swirl chambers. It also varied considerably among cylinders in the same engine. Growth rate correlated well with 0-2% burn but showed negligible correlations with later burn or IMEP. Convection direction proved useful in determining flow direction near the plug.

A study of combustion in a dual-fuel compression ignition engine was conducted to determine the effects of the gaseous fuel addition on the several properties of the combustion process. In particular, the presence and intensity of both end gas knock and diesel knock were measured. A CFR research engine was equipped to run as a dual-fuel engine. Natural gas blends were used for the gaseous fuel fraction, and diesel pilot injection was used as the ignition source. The engine was run at an overall equivalence ratio of 0.7, with premixed equivalence ratios ranging from 0.2 to 0.5. The intake temperature was also varied from 66-110°C. Cylinder pressure data was collected at each point. Three separate methods were used to measure the knock behavior of the engine. Two of these methods were used to quantify the amount of end gas knock which was occurring. Cylinder pressure records were used to calculate a non-dimensional knock factor.

One of the characteristics of nominally homogeneous charge spark ignition engines is a pronounced variation in the combustion rate from cycle to cycle. Many theories have been advanced which attempt to explain the fundamental origin for differences on a cyclic basis. In the present work, some of the suspected causes or their manifestations have been incorporated into Ford's engine combustion model with the intention of determining if their impact on the combustion rate is as theorized. It has been found that initial spark kernel burn rate, the displacement of the spark kernel from the spark plug gap, and the turbulence intensity must all be perturbed simultaneously on a cycle-by-cycle basis to cause the cycle simulation program to mimic the experimentally determined burn parameters with respect to their averages and distributions.

Carbon black particles, which morphologically and chemically simulate a diesel exhaust soot, were mixed with the intake air of a single-cylinder direct injection diesel engine to investigate the efficiency of their removal by oxidation in the combustion chamber. An aerosol generation system, which is capable of generating carbon black aerosol of a size distribution and mass flow rate comparable to those of the soot agglomerates, was developed first. The aerosol was then introduced into the engine which was operating on conventional fuel. Four methods were used to characterize the exhaust particles: an electrical aerosol analyzer, a condensation nuclei counter, a low volume filter, and a micro-orifice cascade impactor. The size distribution and concentration of the diesel soot particles in the lubricants were investigated by methods of photosedimentation and quantitative spectrophotometry, respectively.

The term engine readiness is proposed as an additional concept which should be considered when evaluating among various options for controlling power in homogeneous charge, SI engines. Although improving part load fuel economy is a desirable goal, engine readiness should not be sacrificed in the process. A variety of methods for power control are identified. In general, those which provide superior part load fuel economy suffer from poor response to driver demand, i.e., readiness, and vice versa. Other concerns of load control techniques: range, step size, cost, noise, emissions, safety, complexity, etc., are also considered.

The common method for achieving less than full power operation in a spark ignition (SI) engine is reducing charge density via a throttle. However, a significant fuel economy penalty is associated with the pumping losses across the throttle valve. An alternative method to aid in reducing fresh charge density has been investigated on an Oldsmobile Quad-4 engine: exhaust gas recirculation in combination with inlet air heating. Brake thermal efficiency gains of about 6% were realized. The exhaust hydrocarbon increases associated with EGR were mitigated largely by inlet air heating.

Because of the more hostile environment in the compression ignition engine compared to the spark ignition engine, development and application of CI engine in-cylinder diagnostic methods have lagged those for SI engines. However, with more stringent federally mandated particulate and NOx standards which will go into effect in 1991 and 1994, the need for detailed information on the combustion processes in the cylinder is vital to controlling tailpipe emissions. The present paper contains a summary of the state-of-the-art techniques for determining in-situ species concentrations and profiles; particle concentrations, profiles, and size distributions; and temperature fields. Optical and physical probing methods, total cylinder dumping methods, and optical diagnostics applied for use in CI engine combustion chambers are discussed.