Search Results

Research Octane Number (RON) and Motor Octane Number (MON) are used to describe gasoline combustion which describe antiknock performance under different conditions. Recent literature suggests that MON is less important than RON in modern cars and a relaxation in the MON specification could improve vehicle performance. At the same time, for the same octane number change, increasing RON appears to provide more benefit to engine power and acceleration than reducing MON. Some workers have advocated the use of an octane index (OI) which incorporates both parameters instead of either RON or MON to give an indication of gasoline knock resistance. Previous Concawe work investigated the effect of RON and MON on the power and acceleration performance of two Euro 4 gasoline passenger cars during an especially-designed acceleration test cycle.

A broad range of diesel, kerosene, and gasoline-like fuels has been tested in a single-cylinder diesel engine optimized for advanced combustion performance. These fuels were selected in order to better understand the effects of ignition quality, volatility, and molecular composition on engine-out emissions, performance, and noise levels. Low-level biofuel blends, both biodiesel (FAME) and ethanol, were included in the fuel set in order to test for short-term advantages or disadvantages. The diesel engine optimized in Part 1 of this study included cumulative engine hardware enhancements that are likely to be used to meet Euro 6 emissions limits and beyond, in part by operating under conditions of Homogeneous Charge Compression Ignition (HCCI), at least over some portions of the speed and load map.

Two single-cylinder diesel engines were optimised for advanced combustion performance by means of practical and cumulative hardware enhancements that are likely to be used to meet Euro 5 and 6 emissions limits and beyond. These enhancements included high fuel injection pressures, high EGR levels and charge cooling, increased swirl, and a fixed combustion phasing, providing low engine-out emissions of NOx and PM with engine efficiencies equivalent to today's diesel engines. These combustion conditions approach those of Homogeneous Charge Compression Ignition (HCCI), especially at the lower part-load operating points. Four fuels exhibiting a range of ignition quality, volatility, and aromatics contents were used to evaluate the performance of these hardware enhancements on engine-out emissions, performance, and noise levels.

Recent years have seen dramatic reductions in gasoline and diesel sulfur concentrations in the United States, Europe, Japan and other countries. Many developing countries are evaluating the appropriate sulfur levels to choose for the future. This paper examines the current state of knowledge concerning the impact of fuel sulfur on exhaust emissions, and the sensitivity of exhaust aftertreatment technology to fuel sulfur. Gasoline vehicles achieve very low emissions through use of three-way catalysts. These systems are relatively insensitive to sulfur, being able to operate on levels of up to 500 ppm. Further reduction in sulfur will produce additional, small emission reductions. Diesel emissions may be reduced significantly using engine modifications, oxidation catalysts or exhaust gas recirculation, which may require sulfur levels of 500 ppm.

A consortium of CONCAWE, EUCAR and the EU Commission's JRC carried out a Well-to-Wheels analysis of a wide range of automotive fuels and powertrains. The study gives an assessment of the energy consumption and greenhouse gas emissions for each pathway. It also considers macroeconomic costs and the market potential of alternative fuels.

A combustion-based analytical method, initially developed by the Southwest Research Institute (SwRI) and referred to as the Constant Volume Combustion Apparatus (CVCA), has been further researched/developed by an SwRI licensee (Advanced Engine Technology Ltd.). This R&D has resulted in a diesel fuel Ignition Quality Tester (IQT) that permits rapid and precise determination of the ignition quality of middle distillate and alternative fuels. Its features, such as low fuel volume requirement, complete test automation, and self-diagnosis, make it highly suitable for commercial oil industry and research applications. A preliminary investigation, reported in SAE paper 961182, has shown that the IQT results are highly correlated to the ASTM D-613 cetane number (CN). The objective of this paper is to report on efforts to further refine the original CN model and report on improvements to the IQT fuel injection system.

Particle emissions from vehicles are currently under close scrutiny with respect to their contribution to ambient air quality relative to other sources. Small particles, less than 10 μm, referred to as PM10, have been linked to various health issues. In this study, tests have been performed on European diesel light duty vehicles using a range of production diesel fuels. Tests were also performed on two gasoline passenger cars for comparison. Measurements were made of exhaust particle size distribution and number, as well as mass emissions using the legislated filter paper method. The results showed that most of the particles emitted were very small, with median size of the order 100 nanometres (nm). The median particle size was insensitive to changes in fuel, vehicle or operating condition. Measurements of particle number broadly correlated with particle mass emissions, and ranked fuels and vehicle types in the same order.

The results for the light duty and heavy duty diesel studies in the EPEFE have been compared, and areas of similarity and differences explored. Consistent with the intent to choose the widest possible range of engine technologies and vehicle configurations, the impact of the vehicle and engine sets on emissions was larger than that of the matrix of fuel properties. Vehicles showed a wide range in response to the fuel properties investigated. In some cases, the effects of fuel changes on emissions from the LD vehicle and HD engine sets were similar, but in other cases emissions changed in opposite directions in the two sets for the same fuel change. However, fuel changes that were beneficial for PM in LD vehicles were also positive for NOx and PM in HD engines. Differences between engine design features and test cycles were examined to investigate the reasons for these results. Fuel effects were generally larger in percentage terms for Light Duty Vehicles than for Heavy Duty Engines.

A new technique for measuring ignition quality of diesel fuels has been evaluated. Primarily a constant volume combustion apparatus, the Diesel Fuel Ignition Analyser (DFIA) provides a direct output of ignition delay. Microprocessor control and semi-automatic operation ensure rapid determinations. Tests were performed to find the operating conditions giving the best results in terms of various performance indicators, settling upon 450°C/20bar for combustion air preheat and pressure. A preliminary correlation model based on ignition delay predicted D613 Cetane Number with ± 1.3CN at 95% confidence. More results are required to improve this correlation and define statistical precision of the method.