Search Results

The urea-water-solution based selective catalyst reduction (SCR) system is one of the effective devices for reduction of NOx from diesel engines. In an effort to understand the various levels of oscillation observed in the NOx measurement downstream of a SCR in which the urea dosage is controlled by a crankshaft-link pump, a zero-dimensional dynamic SCR model is developed in this paper based on conservation of mass. The model contains three states including the concentrations of NOx and ammonia in the SCR and the surface coverage rate of the catalyst. The temperature-dependent reactions considered in the model include the adsorption, desorption and oxidation of ammonia and the NOx reduction with the reaction constants provided by the catalyst company. The dynamic SCR model is validated both at steady state and during transient under various engine operating conditions and urea dosing rates.

Crash safety is a changing area in which safety requirements are updated or added from time to time. A relatively recent federal safety requirement is the amended FMVSS 201 rule for upper interior head impact. The automotive crash safety engineer faces many challenges in designing for this safety criterion. In the current study, it is shown how finite element-based simulation can be used as an effective tool in the design of lightweight headform impact protection countermeasures, supplemented with selective laboratory testing. Additionally, judicious employment of component finite element models and laboratory tests before a new countermeasure concept is deployed in a full vehicle environment leads to robustness and efficiency in product development.

The aim of this study was to understand the behavior of Eurosid rib module and its components under different impact conditions. This was achieved by impacting the single rib module at two different velocities of 7.6m/s and 10.8m/s at three impact angles of 0, +30 and -30 deg corresponding to each velocity. All tests were done using a 1.86 kg (4.1 lbs), 152 mm (6″) circular impactor on the Monterey facility (Linear impactor) and some of the tests were filmed at 5000 fps. Tests were also done with and without tuning spring to assess its contribution to the total rib response. The hydraulic damper and damper spring were dynamically tested at different velocities to obtain their individual characteristics of force-velocity and force-deflection respectively. Static force-deflection characteristics of all the four tuning springs and damper spring were also obtained. The results of single rib tests @ 0 deg were compared with the CAE models currently available in MADYMO-3D and RADIOSS.

This paper describes the development of a new component test methodology concept for simulating NHTSA side impact, to evaluate the performance of door subsystems, trim panels and possible safety countermeasures (foam padding, side airbags, etc.). The concept was developed using MADYMO software and the model was validated with a DOT-SID dummy. Moreover, this method is not restricted to NHTSA side impact, but can be also be used for simulating the European procedure, with some modifications. This method uses a combination of HYGE and VIA decelerator to achieve the desired door velocity profile from onset of crash event until door-dummy separation, and also takes into account the various other factors such as the door/B pillar-dummy contact velocity, door compliance, shape of intruding side structure, seat-to-door interaction and initial door-dummy distance.

This paper describes the testing and constitutive model development of polyurethane foams for characterization of their material dynamic properties. These properties are needed not only for understanding their behavior, but also for supplying essential input data to foam models, which help provide design directions through simulations of foam selection for cushioning occupant head impacts against the vehicle door and upper interior. Polyurethane foams of varying densities were tested statically and dynamically under uniaxial compressive impact loading at constant velocities of various rates and different temperatures. The test results were utilized for developing a constitutive model of polyurethane foams by taking the density, strain rate and temperature effects into consideration. Uniaxial constitutive models are developed in two ways.

The University of Virginia is investigating the use of a magnetohydrodynamic (MHD) angular rate sensor to measure head angular acceleration in impact testing. Output from the sensor, which measures angular velocity, must be differentiated to produce angular acceleration. As a precursor to their use in actual testing, a torsional pendulum was developed to analyze an MHD sensor's effectiveness in operating under impact conditions. Differentiated and digitally filtered sensor data provided a good match with the vibratory response of the pendulum for various magnitudes of angular acceleration. Subsequent head drop tests verified that MHD sensors are suitable for measuring head angular acceleration in impact testing.

This paper provides a methodology for adjustment of off-speed head impact test data to the required 24.14 km/h for interior head impact. The “Normalization Process” utilizes the Generic Waveform Concept for its basic foundation. Predicted results from FE Head Impact Simulation Model were used to validate the Normalization Process. It is recommended that Normalization should be applied to cases where impact velocities are within ±0.8 km/h speed difference. In general, Normalizing down-speed (from 24.94 to 24.14 km/h) is preferred over Normalizing up-speed (23.33 to 24.14 km/h). One must always check for potentially severe “bottom-out” condition by examining the pulse shape for any abrupt peaks in headform deceleration. The Normalization Process should not be applied to “glancing” impacts in which the impact and rebound vectors are not colinear.

This paper describes the development of an automated Door Test Facility for implementing the Door Component Test Methodology for side impact analysis. The automated targeting and loading of the door inner/trim panels with Side Impact Dummy (SID) ribcage, pelvis, and leg rams will greatly improve its test-to-test repeatability and expedite door/trim/armrest development/evaluation for verification with the dynamic side impact test of FMVSS 214 (Occupant Side Impact Protection). This test facility, which is capable of evaluating up to four (4) doors per day, provides a quick evaluation of door systems. The results generated from this test methodology provide accurate input data necessary for a MADYMO Side Impact Simulation Model. The test procedure and simulation results will be discussed.

Currently, the three (3) methods for calculating the HIC-value are: 1) direct computation method, 2) utilization of maximization requirement approach developed by Chou and Nyquist, and 3) a partitioning technique. A method which involves the adoption of an optimization approach for HIC calculation is discussed in this study. This optimization technique, which has previously been applied to Boundary Element Method (BEM), employs an improved constrained variable metric method in recursive quadratic programming. This technique was applied to three theoretical and ten experimental acceleration pulses; the results compare extremely well with exact solution and/or other numerical methods. It is concluded that this optimization scheme provides accurate HIC calculations. A study is planned to investigate the feasibility of extending the application of this optimization technique to an integrated trim/foam/sheet metal pillar system for improved interior head impact protection study.

The objective of this study was to determine dynamic tensile characteristics of various door trim materials and to recommend a practical test methodology. In this study, Polypropylene (PP) and Acrilonitryl Butadiene Styrene (ABS) door trim materials were tested. Slow speed (quasi-static-0.021 mm/s) and high speed tests were conducted on a closed loop servo-hydraulic MTS system. The maximum stress of these materials increased from quasi-static to dynamic test conditions (as much as 100%). The dynamic stiffness of PP increased two times from quasi-static tests. No significant change in stiffness was observed for ABS during quasi-static and dynamic tests at different strain-rates. Quasi-static and medium strain-rate (10-20 mm/mm/s) tests may be adequate in providing data for characterizing the dynamic behavior of trim materials for CAE applications. Strain gages can be used to measure the quasi-static and in some cases, dynamic strain.

A constitutive model is developed for strain rate dependent foam and implemented in an explicit dynamic finite element code. The constitutive model is developed in conjunction with a Lagrangian hexahedral solid element with twenty four degrees of freedom. A number of dynamic impact problems involving strain rate dependent foam are analyzed and results are compared with experimental data. In all cases, numerical predictions show excellent agreement with the experiments.

Various foam models are developed using LS-DYNA3D and the model predictions were validated against experiments. Dynamic and static stress-strain relations are obtained experimentally for crushable and resilient foam materials and used as inputs to the finite element analyses. Numerous simulations were carried out for foams subjected to different loading conditions including static compression and indentation, and dynamic impacts with a rigid featureless and a rigid spherical headform. Comparisons of the results obtained from different foam models with test data show appropriate correlations for all the cases studied. Parametric studies of the effects of tensile properties of foam material and the interface parameters on foam performance are also presented.

This paper describes the development of a Dynamic Door Component Test Methodology (DDCTM) for side impact simulation. A feasibility study of the methodology was conducted using a MADYMO computer model by taking parameters such as door pre-crush, door-to-SID (Side Impact Dummy) contact velocity and the deceleration profile into consideration. The prove-out tests of this methodology was carried out on a dynamic sled test facility. The DDCTM has been validated for various carlines. In addition, various existing dynamic component test methods are reviewed. In our approach, a pre-crushed door, mounted on a sled, strikes a stationary SID at a pre-determined velocity. A programmable hydraulic decelerator is used to decelerate the sled to simulate the barrier/door deceleration pulse during door-to-SID contact period. This test procedure provides excellent correlation of the SID responses between the component test and the full-scale vehicle test.

Various foam models are developed using LS-DYNA3D and validated against experiments. Dynamic and static stress-strain relations are obtained experimentally for crushable and resilient foam materials and used as inputs to the finite element analyses. Comparisons of the results obtained from different foam models with test data show excellent correlations for all the cases studied.

NHTSA is expected to publish a final rule on Interior Head Impact (as an amendment to FMVSS 201) by early 1995. One of the Interior Head Impact Study objectives is to develop a methodology for estimating the minimum head impact space requirements to meet this regulation. The physical parameters affecting the HIC (Head Injury Criterion) are impact velocity, maximum headform stopping distance, peak deceleration, and pulse duration. The equations for estimating the HIC vs. Head Impact Space Requirements are formulated by relating these physical parameters to the Idealized Waveforms of Square Wave, Sine Wave, and Haversine Wave. This methodology has been extended to include the Generic Waveform. Tabulations of Maximum Headform Stopping Distance Requirement vs. Peak Deceleration, Pulse Duration, and HIC for the three Idealized Waveforms at 6.7 m/s (15 mph) impact speed have been generated to provide an estimate of the head impact package space requirement.

This report describes an experimental validation of an ellipsoid-to-foam contact model. A series of static foam tests was conducted using Side Impact Dummy rib cage, pelvis, upper leg, and wooden ellipsoids as impactors to validate a theoretical foam contact model previously developed. Predicted results of contact forces, calculated using the uni-axial stress-strain relationship and contact areas, yield good correlation with the test data. These studies used CFC foams and were conducted prior to switching to water-blown foam material development. The ellipsoid-to-foam contact model is being integrated into a MADYMO side impact model. The MADYMO/foam simulation model can then be used to help evaluate design variable tradeoffs (e.g., door thickness vs. body side structures and foam padding requirement vs. interior package) thereby reducing the current dependency on testing, bolster development time, and cost.

This paper deals with the constitutive modeling of energy absorbing foams. Two mechanical-analog hyper-elastoplastic models are constructed for simulating the characteristics of semi-rigid and rigid foams. These piecewise linear models are suitable for describing the loading as well as the unloading behavior of material. The result from quasi-static compression tests are used to determine the three parameters of the models. It is observed that the models can be used in the prediction of stress-strain behavior as well as the energy absorption characteristics.

The viscous criterion (V*C) has been proposed by biomechanics researchers as a generic biomechanical index for potential soft tissue injury. It is defined by the product of the velocity of deformation and the instantaneous compression of torso and abdomen. This criterion requires calculation and differentiation of measured torso/abdomen compression data. Various computational algorithms for calculating viscous criterion are reviewed and evaluated in this paper. These include methods developed by Wayne State University (WSU), NHTSA (DOT) and Ford. An evaluation has been conducted considering the accuracy of these algorithms with both theoretical and experimental data from dummy rib compressions obtained during a crash test. Based on these results, it is found that: V*C results depend on the scheme used in the computation process, the sampling rate and filtering of original raw data. The NHTSA method yields the lowest V*C value.

A highly controlled six-vehicle crash test program was conducted to provide an estimate of the test-to-test variability of the NHTSA-proposed passenger car dynamic side impact test procedure. The results of this program showed that the rear seat test dummy response measurements are especially sensitive to various parameters of the test procedure. This paper provides estimates of front and rear seated SID dummy response measurement variability in four-door, 1990 Ford Taurus vehicles. Conclusions and recommendations from this controlled crash test program are made to provide guidance to help reduce the test-to-test variability of the test dummy responses.