Search Results

In the highly innovative and holistic flagship project HySnow (Decarbonisation of Winter Tourism by Hydrogen Powered Fuel Cell Snowmobiles), funded by the Austrian Climate and Energy Fund, the decarbonization of winter tourism is being demonstrated. Within this project, two prototype e-snowmobiles have been developed including the adaption of a Polymer Electrolyte Membrane Fuel Cell (PEM-FC) system for the low temperature and high-performance targets and the integration of the drivetrain into the vehicle. In this paper the drivetrain development process of the prototype e-snowmobiles will be presented with the aim to derive specifications for the drivetrain components as PEM-FC system, hydrogen storage system, electric drive, battery and power electronics. Based on typical use cases for snowmobiles overall vehicle specifications and requirements are defined. Associated driving cycles are investigated and used as input for the development process.

The limitation of global warming to less than 2 °C till the end of the century is regarded as the main challenge of our time. In order to meet COP21 objectives, a clear transition from carbon-based energy sources towards renewable and carbon-free energy carriers is mandatory. Polymer electrolyte membrane fuel cells (PEMFC) allow an energy-efficient, resource-efficient and emission-free conversion of regenerative produced hydrogen. For these reasons fuel cell technologies emerge in stationary, mobile and logistic applications with acceptable cruising ranges as well as short refueling times. In order to perform applied research in the area of PEMFC systems, a highly integrated fuel cell analysis infrastructure for systems up to 150 kW electric power was developed and established within a cooperative research project by HyCentA Research GmbH and AVL List GmbH in Graz, Austria. A novel open testing facility with hardware in the loop (HiL) capability is presented.

The continuous increasingly stringent regulations for CO2 fleet targets request the introduction of zero-emission solutions in the near future. Moreover, additional customer benefits have to be generated in order to increase customer acceptance of zero-emission technologies. Actually high costs, reduced driving ranges and lack of infrastructures are some aggregative facts for end-customer acceptance thus also for a broad market launch. Plug-in hybrids as intermediate step towards zero-emission vehicles are meanwhile in series production with partly “zero-emission” operation mode and are well accepted by customers. The project partners HyCentA Research GmbH, Magna Steyr Engineering AG & Co KG, Proton Motor Fuel Cell GmbH and the Vienna University of Technology, Institute for Powertrains and Automotive Technology, have developed a hydrogen-powered zero-emission vehicle within a national funded research project.

Hydrogen as carbon-free energy carrier, produced from renewable sources like wind, solar or hydro power, is a promising option to overcome the impacts of the anthropogenic climate change. Recently, great advances regarding the early market introduction of FCVs have been achieved. As the availability of hydrogen refueling stations is highly limited, a modular, scalable and highly efficient hydrogen supply infrastructure concept is presented in this paper. The focus lies on cost-effectiveness and flexibility for the utilization in different applications and for growing markets. Based on the analysis of different use cases, the requirements for the newly developed concept are elaborated. The modular system design, utilizing a standardized high pressure PEM electrolysis module, allows a scalable hydrogen production of up to several hundred kilograms per day.

The enhancement of efficiency will play a more and more important role in the development of future (small) internal combustion engines. In recent years, the Atkinson cycle, realized over the crank drive, has attracted increasing attention. Several OEMs have been doing investigations on this efficiency-increasing principle with in the whole range from small engines up to automotive ones. In previous publications, the authors stated that an indicated efficiency of up to 48% could be reached with an Atkinson cycle-based engine. However, these studies are based on 1D-CFD simulation. To verify the promising simulation results, a prototype engine, based on the Atkinson principle, was designed and experimentally tested. The aim of the present study is to evaluate and validate the (indicated) engine efficiency gained by experimental tests compared to the predicted simulation results. In order to investigate part load behavior, several valve timing strategies were also developed and tested.

Millions of small displacement single-cylinder engines are used for the propulsion of scooters, motorcycles, small boats and others. These SI-engines represent the basis of an affordable mobility in many countries, but at the same time their efficiency is quite low. Today, the limited fossil fuel resources and the anthropogenic climate require a sustainable development of combustion engines, the reduction of fuel consumption being an important factor. A variety of different strategies (turbo-charging, cylinder deactivation, direct injection, etc.) are investigated here to increase the efficiency of multi-cylinder engines. In the case of small displacement single-cylinder engines, other strategies are required because of their special design and the high pressure on costs. In the context of this paper different layout parameters which have an influence on the working process are investigated, with the aim of increasing the efficiency of small displacement single-cylinder engines.

One of the most significant current discussions worldwide is the anthropogenic climate change accompanying fossil fuel consumption. Sustainable development in all fields of combustion engines is required with the principal objective to enhance efficiency. This certainly concerns the field of hand-held power tools as well. Today, two-stroke SI engines equipped with a carburetor are the most widely used propulsion technology in hand-held power tools like chain saws and grass trimmers. To date, research tended to focus on two-stroke engines with rich mixture setting. In this paper the advantages and challenges of leaner and/or lean operation are discussed. Experimental investigations regarding the influence of equivalence ratio on emissions, fuel consumption and power have been performed. Accompanying 3D-CFD simulations support the experiments in order to gain insight into these complex processes. The investigations concentrate on two different mixture formation processes, i.e.

The automotive industry has made great efforts in reducing fuel consumption. The efficiency of modern spark ignition (SI) engines has been increased by improving the combustion process and reducing engine losses such as friction, gas exchange and wall heat losses. Nevertheless, further efficiency improvement is indispensable for the reduction of CO2 emissions and the smart usage of available energy. In the previous years the Atkinson Cycle, realized over the crank train and/or valve train, is attracting considerable interest of several OEMs due to the high theoretical efficiency potential. In this publication a crank train-based Atkinson cycle engine is investigated. The researched engine, a 4-stroke 2 cylinder V-engine, basically consists of a special crank train linkage system and a novel Mono-Shaft valve train concept.

Meeting future legislative targets for SI engines by means of low cost technologies is a big challenge for engineers. Despite the use of simple and cost efficient components these engines have to fulfill customer requirements in terms of power and fuel economy, representing the most important selling arguments. Without the possibility of integrating modern technologies like fuel injection systems for mixture preparation instead of simple carburetors, it is very complex to find viable solutions that enable the achievement of these targets. A main key to improve emission behavior, fuel economy and performance on carbureted engines is to get an insight in the mixture preparation process, especially under transient conditions.

This paper introduces a research project on a spark ignition engine used in non-road applications. The aim is to illustrate the present situation as basis for comparison and to identify possible improvement potential in terms of performance, efficiency or exhaust and noise emissions. The study is carried out in two steps. First a standard walk-behind lawn mower is equipped with measuring instrumentation for recording the cutting forces and the engine variables during real world operation. The tests are carried out on three different lawn types and two different blade types are investigated. Consequently, in a second step the engine is analysed on the engine test bench in stationary and transient operating mode. A complete engine mapping is done regarding all relevant variables. Additionally to the outdoor tests, fuel consumption and engine out emissions are measured on the engine dynamometer. The recorded data enables a detailed analysis of the engine behaviour.

Today mankind is using highly sophisticated tools which contribute to maintain the standard of living. Nevertheless, these tools have to be further improved in the near future in order to protect health and environment as well as to ensure prosperity. Two-stroke engines equipped with a carburettor are the most used propulsion technology in hand-held power tools like chain saws and grass trimmers. The shortage of fossil resources and the necessary reduction of carbon dioxide emissions ask for improved engine efficiency. Concurrently, customers demand for an easy usage with high performance at all operating conditions, e.g. varying ambient temperature and pressure and different fuels. Moreover, world-wide emission limits will be even stricter in future. The improvement of the emission level, fuel consumption and customer benefits, while keeping the present advantages of two-stroke engines, like high specific power and simplicity, are the goals of this research work.

Small combustion engines can be found in various applications in daily use (e.g. as propulsion of boats, scooters, motorbikes, power-tools, mobile power units, etc.) and have predominated these markets for a long time. Today some upcoming competitive technologies in the field of electrification can be observed and have already shown great technical advances. Therefore, small combustion engines have to keep their present advantages while concurrently minimizing their disadvantages in order to remain the predominant technology in the future. Whereas large combustion engines are most efficient thermal engines, small engines still suffer from significantly lower efficiencies caused by a disadvantageous surface to volume ratio. Thus, the enhancement of efficiency will play a key role in the development of future small combustion engines. One promising possibility to improve efficiency is the use of a longer expansion than compression stroke.

This publication covers investigations on different 3D CFD models for the description of the spray wall and droplet-fluid interaction and the influence of these models on the mixture formation calculation results. Basic experimental investigations in a spray chamber and a flow tunnel as well as the corresponding 3D CFD simulation were conducted in order to clarify the prediction quality of the physical phenomena of spray-wall and spray-fluid interaction by the simulation. Influencing parameters such as the piston top temperature, piston bowl geometry, soot deposits on the piston top as well as flow velocity are investigated. This paper provides a direct link between the underlying simulation models of the mixture formation and actual real world combustion system development processes - underlining the importance of a close interaction of the model calibration and the development process.

In the course of the last few years a continuous increase of the injection pressure level of gasoline direct injection systems appeared. Today's systems use an injection pressure up to 200bar and the trend shows a further increase for the future. Although several benefits go along with the increased injection pressure, the disadvantages such as higher system costs and higher energy demand lead to the question of the lowest acceptable injection pressure level for low cost GDI combustion systems. Lowering injection pressure and costs could enable the technological upgrading from MPFI to GDI in smaller engine segments, which would lead to a reduction of CO2 emission. This publication covers the investigation of a low pressure GDI system (LPDI) with focus on small and low cost GDI engines. The influence of the injection pressure on the fuel consumption and emission behavior was investigated using a 1.4l series production engine.

This publication presents the development of a GDI combustion system for high speed - high performance engines. The paper describes the development of the combustion process and its results, the development methodology, covering 1D and 3D CFD simulations, and shows extensive experimental investigations. With 3D CFD simulations the necessary deeper insights in the mixture preparation process of a homogenous GDI combustion system are gained. The findings of the simulation are transferred to an injection and combustion system for a 4-cylinder test engine. The results of the experimental investigations of the 4-cylinder engine equipped with GDI technology show the potential of GDI applications for high performance engines.