Search Results

In earlier work we have shown that engine operation with oxygenated fuels (e.g., biodiesel) reduces the particulate matter (PM) emissions and extends the engine tolerance to exhaust gas recirculation (EGR) before it reaches smoke limited conditions. The same result has also been reported when high cetane number fuels such as gas-to-liquid (GTL) are used. A likely mechanism for engine-out particulate growth is the reintroduction of particle nuclei into the cylinder through EGR. These recirculated PM particles serve as sites for further condensation and accumulation promoting larger and greater number of particles. In order to further our understanding of EGR influence on total PM production, a diesel particulate filter (DPF) was integrated into the EGR loop. A PM reduction of approximately 50% (soot) was achieved with diesel fuel through filtered EGR, whilst still maintaining a significant NOX reduction.

The fuel reforming technology has been extensively investigated as a way to produce hydrogen on-board a vehicle that can be utilized in internal combustion engines, fuel cells and aftertreatment technologies. Maximization of H2 production in the reforming process can be achieved when there is optimized water (steam) addition for the different reforming temperatures. A way to increase the already available water quantity on-board a vehicle (i.e. exhaust gas water content) is by using emulsified fuel (e.g. water-diesel blend). This study presents the effect of an emulsified diesel fuel (a blend of water and diesel fuel with an organic surfactant to make the mixture stable) on combustion in conjunction with exhaust gas assisted fuel reforming on a compression ignition engine. No engine modification was required to carry out these tests. The emulsified diesel fuel consisted of about 80% (mass basis) of conventional ultra low sulphur diesel (ULSD) fuel and fixed water content.

Biofuels development and specification are currently driven by the engine (mainly gasoline- and diesel-type) technology, existing fossil fuel specification and availability of feedstock. The ability to use biofuels with conventional fuels without jeopardising the standard fuel specifications is a very effective means for the implementation of these fuels. In this work the effect of dual fuelling with in-cylinder injected ULSD fuel or synthetic second generation biofuels (a Gas-To-Liquid GTL fuel as a surrogate of these biofuels as its composition, specifications and production process are very similar to second generation biofuels) and with inlet port injected bioethanol on the engine performance and emissions were investigated. The introduction of anhydrous bioethanol improved the NOx and smoke emissions, but increased total hydrocarbons and carbon monoxide.

Limits on the total future potential of biodiesel fuel due to the availability of raw materials mean that ambitious 20% fuel replacement targets will need to be met by the use of both first and next generation biodiesel fuels. The use of higher percentage biodiesel blends requires engine recalibration, as it affects engine performance, combustion patterns and emissions. Previous work has shown that the combustion of 50:50 blends of biodiesel fuels (first generation RME and next generation synthetic fuel) can give diesel fuel-like performance (i.e. in-cylinder pressure, fuel injection and heat release patterns). This means engine recalibration can be avoided, plus a reduction in all the regulated emissions. Using a 30% biodiesel blend (with different first and next generation proportions) mixed with Diesel may be a more realistic future fuel.

In the present work, the partial oxidation of diesel (US07), rapeseed methyl ester (RME) and low temperature Fischer - Tropsch synthetic diesel (SD), almost 100% paraffinic, was investigated for the purpose of hydrogen and intermediate hydrocarbon species production over a prototype reforming catalyst, for the potential use in hydrocarbon selective catalytic reduction (HC-SCR) of nitrogen oxide (NOx) emissions from diesel engines. The presence of small amounts of hydrogen can substantially improve the effectiveness of hydrocarbons in the selective reduction of NOx over lean NOx catalysts, particularly at low temperatures (150-350°C). In this study, the partial oxidation reactor was operating at the same input power (kW), based on the calorific values of the fed fuel. Hydrogen production was as high as 19%, from the partial oxidation of SD fuel, and dropped to 17% and 14% for RME and US07 diesel, respectively.

A prototype catalyst has been developed and integrated within the aftertreatment exhaust system to control the HC, CO, PM and NOx emissions from diesel exhaust gas. The catalyst activity in removing HC and nano-particles was examined with exhaust gas from a diesel engine operating on biodiesel - Rapeseed Methyl Ester (RME). The tests were carried out at steady-state conditions for short periods of time, thus catalyst tolerance to sulphur was not examined. The prototype catalyst reduced the amount of hydrocarbons (HC) and the total PM. The quantity of particulate with electrical mobility diameter in nucleation mode size < 10nm, was significantly reduced over the catalyst. Moreover, it was observed that the use of EGR (20% vol.) for the biodiesel fuelled engine significantly increases the particle concentration in the accumulation mode with simultaneous reduction in the particle concentration in the nuclei mode.

It is known that the levels of hydrocarbon (HC) emissions from Homogeneous Charge Compression Ignition (HCCI) engines are relatively higher than that of Spark-Ignition (SI) engines because of the lower combustion temperature. In order to improve understanding of the mechanisms and products of HCCI combustion in comparison with SI combustion, a quantitative analysis of individual hydrocarbons in the C1 - C6 range emitted in the exhaust gases of gasoline direct injection V6 engine operating in SI and HCCI modes with cam profile switching has been carried out using gas chromatography - mass spectrometry (GCMS) apparatus attached on-line to engine exhaust. In this study, with a GC run time of 20 minutes all aliphatic and olefinic hydrocarbon species in the range C1 to C6 are resolved.

Increasing biodiesel content in mineral diesel is being promoted considerably for road transportation in Europe. With positive benefits in terms of net CO2 emissions, biofuels with compatible properties to those of conventional diesel are increasingly being used in combustion engines. In comparison to standard diesel fuel, the near zero sulphur content and low levels of aromatic compounds in biodiesel fuel can have a profound effect not only on combustion characteristics but on engine-out emissions as well. This paper presents analysis of particulate matter (PM) emissions from a turbo-charged, common rail direct injection (DI) V6 Jaguar engine operating with an RME (rapeseed methyl ester) biodiesel blended with ultra low sulphur diesel (ULSD) fuel (B30 - 30% of RME by volume). Three different engine load and speed conditions were selected for the test and no modifications were made to the engine hardware or engine management system (EMS) calibration.

Producing on-board the hydrogen that is to be used as supplementary fuel by exhaust gas reforming of gasoline shows encouraging results. Extensive research has been done at the University of Birmingham towards on board generation of hydrogen-rich gaseous fuel. Exhaust gas reforming which utilizes water vapor and enthalpy from the hot engine exhaust gas was applied using a compact system of a fuel reformer reactor integrated with the three way catalytic converter (TWC). Such system can be fitted in the limited space close to the engine. The device has been designed and built in concentric shape with the catalytic converter as a core and the reformer in an annular shape outside, to best utilize the waste heat from the catalytic converter. It requires very little extra space beyond the baseline catalytic converter.

The hydrocarbon-SCR activity of a silver catalyst has been examined using actual exhaust gas from a diesel engine, without any fuel being added to the reactor inlet. This work is a further step in the development of an active lean-NOx catalyst for aftertreatment of exhaust streams that contain an excess of hydrocarbon relative to NOx. The engine tests follow on from laboratory studies, in which the activity was related to the composition and formulation of the catalyst, the concentration and speciation of the hydrocarbon reductants, and the composition and temperature of simulated exhaust gas. In all the tests described here, the exhaust gas has been provided by an engine operating on ultra-low sulphur diesel fuel. NOx-reduction has been measured as a function of engine load, engine speed, in-cylinder fuel injection timing, exhaust gas temperature, and exhaust gas recirculation. Over 60% conversion to N2 has been achieved at exhaust gas temperatures around 290°C.

Control of NOx and Particulate Matter (PM) emissions from diesel engines remains a significant challenge. One approach to reduce both emissions simultaneously without fuel economy penalty is the reformed exhaust gas recirculation (REGR) technique, where part of the fuel is catalytically reacted with hot engine exhaust gas to produce a hydrogen-rich combustible gas that is then fed to the engine. On the contrary to fuel cell technology where the reforming requirements are to produce a reformate with maximized H2 concentration and minimized (virtually zero) CO concentration, the key requirement of the application of the exhaust gas fuel reforming technique in engines is the efficient on-demand generation of a reformate with only a relatively low concentration of hydrogen (typically up to 20%).

Previous work of the authors' group has shown that biodiesel fuels as a replacement for conventional diesel fuel in engine combustion can reduce PM level dramatically while lowering some other regulated emissions as well. It has shown that these fuels have the potential to increase the overall engine performance due to their lower sulphur and/or aromatics content compared with standard diesel fuels. This paper presents a study on a single cylinder naturally aspirated direct injection (DI) diesel engine, equipped with a pump-line-nozzle injection system, operating with varied biodiesel fuel blends (0%, 25%, and 50% of RME by volume) with ultra low sulphur diesel fuel (ULSD). The detailed analysis of the measurement data shows that the ignition delay and exhaust emissions are affected by the proportion of biodiesel due to the effect of different physical and chemical properties of the two fuels.

The Reformed EGR (REGR) technique involves the injection of hydrocarbon fuel (e.g., diesel) into a catalytic reformer fitted into the engine EGR system, so that the produced hydrogen containing gas mixture is fed back to the engine as REGR. Thus, in effect the engine operates in a similar way to a dual fuelled engine with standard EGR. Depending on the reforming conditions, the composition and the calorific value of the REGR may vary and this affects the engine performance and emissions. In the present study, simulated REGR with different H2/CO ratios has been examined. The combustion of REGR with maximum H2 and minimum CO contents resulted in the highest reduction of NOx emissions. This case simulated the reformer operation where the CO is fully converted to H2 by promoting the exothermic water gas shift reaction (WGSR). The highest reductions of both smoke and fuel consumption were achieved in the case of simulating the reformer operation where the CO is not fully converted to H2.

This paper describes the results of an experimental investigation of the exhaust gas assisted fuel reforming process as a means of achieving reduction of both smoke and NOx diesel engine emissions. Using a reforming mini-reactor with exhaust gas from a single-cylinder DI diesel engine, diesel fuel was reformed and a hydrogen-rich gas was produced. The effects of the reforming process on the engine operation were studied by adding simulated reformer product gas to the engine inlet. In this way, the engine was operated as if a reformer would have been incorporated in the exhaust gas recirculation system (EGR) system providing the engine with ‘reformed EGR’ (REGR). Lower levels of REGR resulted in simultaneous reduction of smoke and NOx while increased REGR reduced smoke further but tended to increase NOx.