Search Results

Classic vehicle production had limitations in bringing the driving commands to the actuators for vehicle motion (engine, steering and braking). Steering columns, hydraulic tubes or steel cables needed to be placed between the driver and actuator. Change began with the introduction of e-gas systems. Mechanical cables were replaced by thin, electric signal wires. The technical solutions and legal standardizations for addressing the steering and braking systems, were not defined at this time. Today, OEMs are starting E/E-Architecture transformations for manifold reasons and now have the chance to remove the long hydraulic tubes for braking and the solid metal columns used for steering. X-by-wire is the way forward and allows for higher Autonomous Driving (AD) levels for automated driving vehicles. This offers new opportunities to design the vehicle in-cabin space. This paper will start with the introduction of x-by-wire technologies.

The powertrain module is being introduced to embedded System on Chips (SoCs) designed to increase available computational power. These high-performance SoCs have the potential to enhance the computational power along with providing on-board resources to support unexpected feature growth and on-demand customer requirements. This project will investigate the radial basis function (RBF) using the Gaussian process (GP) regression algorithm, the ETAS ASCMO tool, and the hardware accelerator Advanced Modeling Unit (AMU) being introduced by Infineon AURIX 2nd Generation. ETAS ASCMO is one of the solutions for data-driven modeling and model-based calibration. It enables users to accurately model, analyze, and optimize the behavior of complex systems with few measurements and advanced algorithms. Both steady state and transient system behaviors can be captured.

Vehicle Security means protecting potential threats, unintended malfunction and illegal tuning. In addition, it has become a more important issue on an automotive system as it is directly connected to the driver and pedestrian's life. Automotive industry significantly needs to enhance security policies to prevent attacks from hackers. Nevertheless, in some systems, performance still has to be considered at first when security functions are implemented. Especially, in case of Engine Management System (EMS), fast engine synchronization for starting should be considered as the first priority. This paper is intended to show an approach to design efficient secure boot implementation for EMS. At the beginning of this paper, the concept of secure boot is explained and several use cases are introduced according to execution modes, such as the foreground and background secure boot modes. As a next step, engine starting process by EMS is explained.

Cyber security is becoming increasingly critical in the car industry. Not only the entry points to the external world in the car need to be protected against potential attack, but also the on-board communication in the car require to be protected against attackers who may try to send unauthorized CAN messages. However, the current CAN network was not designed with security in mind. As a result, the extra measures have to be taken to address the key security properties of the secure CAN communication, including data integrity, authenticity, confidentiality and freshness. While integrity and authenticity can be achieved by using a relatively straightforward algorithms such as CMAC (Cipher-based Message Authentication Code) and Confidentiality can be handled by a symmetric encryption algorithm like AES128 (128-bit Advanced Encryption Standard), it has been recognized to be more challenging to achieve the freshness of CAN message.

Vehicle manufacturers are challenged by rising costs for vehicle recalls. A major part of the costs are caused by software updates. This paper describes a feasibility study on how to implement software update over the air (SOTA) in light vehicles. The differences and special challenges in the automotive environment in comparison to the cellular industry will be explained. Three key requirements focus on the drivers’ acceptance and thus are crucial for the vehicle manufacturers: SOTA must be protected against malicious attacks. SOTA shall interfere as little as possible with the availability of a vehicle. Long update processes with long vehicle downtimes or even complete fails must be avoided. The functional safety of the vehicle during operation may not be limited in any way The study gives options how those objectives can be achieved. It considers the necessary security measures and describes the required adaptations of the board-net architectures both on software and hardware level.

This paper will give an overview of multicore in automotive applications, covering the trends, benefits, challenges, and implementation scenarios. The automotive silicon industry has been building multicore and multiprocessor systems for a long time. The reasons for this choice have been: increased performance, safety redundancy, increased I/O & peripheral, access to multiple architectures (performance type e.g. DSP) and technologies. In the past, multiprocessors have been mainly considered as multi-die, multi-package with simple interconnection such as serial or parallel busses with possible shared memories. The new challenge is to implement a multicore, micro-processor that combines two or more independent processors into a single package, often a single integrated circuit (IC). The multicores allow a computing device to exhibit some form of thread-level parallelism (TLP).

Trends in today's and future embedded powertrain systems show a strongly growing demand of communication between the functional units inside a car. A cost optimized system partitioning leads to several independent building blocks that have to be interconnected. Depending on the task of each building block, different classes of data exchange can be distinguished, differing in the required bandwidth, the tolerated latency and speed for real time critical tasks. In order to minimize the communication effort concerning time, chip size and overall costs, different communication requirements have been analyzed. The results lead to improvements of standard serial interfaces by application-oriented features.