Search Results

This paper presents an integrated control of in-wheel motor (IWM) and electronic limited slip differential (eLSD) to enhance the vehicle lateral stability and maneuverability. The two actuators are utilized in the proposed controller to achieve separate purposes. The IWM controller is designed to modify the understeer gradient for enhanced handling characteristic and maneuverability. The eLSD controller is devised to improve the lateral stability to prevent oversteer in a severe maneuver. The proposed controller consists of a supervisor, upper-level controller and lower-level controller. The supervisor determines a target motion based on a target understeer gradient for IWM control and a yaw rate reference for eLSD control. The upper-level controller generates a desired yaw moment for the target motion. In the lower-level controller, the desired yaw moment is converted to the control inputs for IWMs in the two front wheels and eLSD at the rear axle.

This paper presents the research related to the self-driving system that has been actively carried out recently. Previous studies have been limited to ensure the path following performance in linear and steady state-alike handling region with small lateral acceleration. However, in the high speed driving, the vehicle cornering response is extended to nonlinear region where tire grips are saturated. This requires a technology to create the driving path for minimum time maneuvering while grasping the tire grip limits of the vehicle in real time. The entire controller consists of three stages-hierarchy: The target motion is determined in the supervisor phase, and the target force to follow the target behavior is calculated in the upper stage controller. Finally, the lower stage controller calculates the actuator phase control input corresponding to the target force.

This paper presents an Interacting Multiple Model (IMM) based side slip angle estimation method to estimate side slip angle under various road conditions for vehicle stability control. Knowledge of the side slip angle is essential enhancing vehicle handling and stability. For the estimation of the side slip angles in previous researches, prior knowledge of tire parameters and road conditions have been employed, and sometimes additional sensors have been needed. These prior knowledge and additional sensors, however, necessitates many efforts and make an application of the estimation algorithm difficult. In this paper, side slip angle has been estimated using on-board vehicle sensors such as yaw rate and lateral acceleration sensors. The proposed estimation algorithm integrates the estimates from multiple Kalman filters based on the multiple models with different parameter set.

This paper proposes a rear-wheel steering control method that can modify and improve the vehicle lateral response without tire model and parameter. The proposed control algorithm is a combination of steady-state and transient control. The steady state control input is designed to modify steady-state yaw rate response of the vehicle, i.e. understeer gradient of the vehicle. The transient control input is a feedback control to improve the transient response when the vehicle lateral behavior builds up. The control algorithm has been investigated via computer simulations. Compared to classical control methods, the proposed algorithm shows good vehicle lateral response such as small overshoot and fast response. Specifically, the proposed algorithm can alleviate stair-shaped response of the lateral acceleration.

This paper presents an integrated chassis control method for vehicle stability under various road friction conditions without information on tire-road friction. For vehicle stability, vehicle with an integrated chassis control needs to cope with the various road friction conditions. One of the chassis control method under various road conditions is to determine and/or limit control inputs based on tire-road friction coefficient. The tire-road friction coefficient, however, is difficult to estimate and still a challenging task. The key idea for the proposed method without the estimation of the tire-road friction coefficient is to analyze and control vehicle states based on a tire slip angle - tire force phase plane, i.e. based on these vehicle responses: tire forces and tire slip angles of front/rear wheels.

This paper presents the integrated chassis control(ICC) of four-wheel drive(4WD), electronic stability control(ESC), electronic control suspension(ECS), and active roll stabilizer(ARS) for limit handling. The ICC consists of three layers: 1) a supervisor determines target vehicle states; 2) upper level controller calculates generalized forces; 3) lower level controller, which is contributed in this paper, optimally allocates the generalized force to chassis modules. The lower level controller consists of two integrated parts, 1) longitudinal force control part (4WD/ESC) and 2) vertical force control part (ECS/ARS). The principal concept of both algorithms is optimally utilizing the capability of the each tire by monitoring tire saturation, with tire combined slip. By monitoring tire saturation, 4WD/ESC integrated system minimizes the sum of the tire saturation, and ECS/ARS integrated system minimizes the variance of the tire saturation.

This paper describes an Integrated Chassis Control (ICC) strategy for improving high speed cornering performance by integration of Electronics Stability Control (ESC), Four Wheel Drive (4WD), and Active Roll Control System (ARS). In this study, an analysis of various chassis modules was conducted to prove the control strategies at the limits of handling. The analysis is focused to maximize the longitudinal velocity for minimum lap time and ensure the vehicle lateral stability in cornering. The proposed Integrated Chassis Control algorithm consists of a supervisor, vehicle motion control algorithms, and a coordinator. The supervisor monitors the vehicle status and determines desired vehicle motions such as a desired yaw rate, longitudinal acceleration and desired roll motion. The target longitudinal acceleration is determined based on the driver's intention and vehicle current state to ensure the vehicle lateral stability in high speed maneuvering.