Search Results

A promising approach for defossilization in the transport sector is using the polymer electrolyte membrane fuel cell (PEMFC) as an energy converter for propulsion in combination with green hydrogen. Furthermore, hybridization can bring an additional gain in efficiency. In a hybrid electric vehicle (HEV) powertrain, including FCHEV, at least two power sources (e.g., an FC system (FCS) with a hydrogen storage system and a high-voltage battery (HVB)) provide the required propulsion power. Thus, the powertrain topology and the energy management strategy (EMS) of an FCHEV are more complex than those of a conventional powertrain. To ensure a cost- and time-efficient development process, the FCHEV powertrain concept and its functions must be verified and evaluated early. To this end, this study presents the design and setup of an FC-in-the-Loop (FCiL) test platform as a tool for the systematic development of an FCHEV powertrain under realistic operating conditions.

The electric range of plug-in hybrids as well as the installed electric power has steadily increased. With an electric power share of more than half of the overall system power, concepts of hybrid electric vehicles with at least two electric machines come into focus. Especially the concept of adding an individual electric axle to a state-of-the-art parallel hybrid, such as a P2-hybrid, is promising. However, the system complexity of a so-called P24-hybird increases significantly because the number of possible system states rises. This leads to an increased development and calibration effort for an online energy management. Especially a transfer from an optimized operating strategy to a rule-based energy management is challenging. Thus, a development framework for the calibration of an online energy management system (EMS) which is as fuel efficient as possible is needed.

In order to adhere with future automotive legislation and incentives, the electric range of plug-in hybrids has steadily increased. At the same time, the installed electric power has risen as well leading to future hybrid vehicles with an electric power share of more than half of overall system power and hybrid configurations with at least two electrical machines come into focus. The concept of adding a separate electrical axle to a P2-hybrid - a so called P24-hybrid, is of special interest. The system complexity of a such a system increases significantly as the number of possible system states increases. Thus, this paper analyzes the efficiencies and benefits of the different system states within the fuel-optimal operating strategy derived by global optimization. By varying the electrical power distribution between the two axles, the impact on fuel efficiency and the changes within the operating strategy are investigated.

The efficiency of a Hybrid Electric Vehicle (HEV) strongly depends on its implemented Energy Management Strategy (EMS) that splits the driver’s torque request onto the Internal Combustion Engine (ICE) and Electric Motor (EM). For calibrating these EMS, usually, steady-state efficiency maps of the power converters are used. These charts are mainly derived from measurements under optimal conditions. However, the efficiency of ICEs fluctuates strongly under different conditions. Among others, these fluctuations can be induced by charge air temperature, engine oil temperature or the fuel’s knock resistance. This paper proposes a new approach for predicting the impact of any external influence onto the ICE efficiency. This is done by computing the actual deviation from the optimal reference ignition timing and adjusting the result by actual oil temperature and target air-to-fuel ratio.

The usage of ethanol and two different mixtures of ethanol and gasoline (E85 and E65) wаs investigated on a modified diesel engine designed to work in a dual-fuel combustion mode with intake manifold alcohol injection. The maximum ratio of alcohol to diesel fuel was limited by irregular combustion phenomena like degrading combustion quality and poor process controllability at low load and knock as well as auto-ignition at high load. With rising alcohol amount, a significant reduction of soot mass and particle number was observed. At some testing points, substituting diesel with ethanol, E65 or E85 led to a reduction of NOx emissions; however, the real benefit concerning the nitrogen oxides was introduced by the mitigation of the soot-NOx trade-off. The indicated engine efficiency in dual-fuel mode showed an extended tolerance against high EGR rates. It was significantly improved with enhanced substitution ratios at high loads, whereas it dropped at low loads.

Fuel cells as alternative propulsion systems in vehicles can achieve higher driving ranges and shorter refueling times compared to pure battery-electric vehicles, while maintaining the local zero-emission status. However, to take advantage of pure battery electric driving, an externally rechargeable battery can be combined with a fuel cell range extender. As part of a research project, an efficient air supply system for a fuel cell range extender was developed. To this end, a 25 kW PEM fuel cell system test bench was set up. The different parameter influences of the test bench, in particular of the air supply system, were analyzed and evaluated in terms of stack/system efficiency and functionality. The control software of the test bench was specifically developed for the flexible operating parameter variation. All adjustable variables of the system (air ratio, stack temperature, pressure, etc.) were varied and evaluated at steady-state operating points.

The continuous increasingly stringent regulations for CO2 fleet targets request the introduction of zero-emission solutions in the near future. Moreover, additional customer benefits have to be generated in order to increase customer acceptance of zero-emission technologies. Actually high costs, reduced driving ranges and lack of infrastructures are some aggregative facts for end-customer acceptance thus also for a broad market launch. Plug-in hybrids as intermediate step towards zero-emission vehicles are meanwhile in series production with partly “zero-emission” operation mode and are well accepted by customers. The project partners HyCentA Research GmbH, Magna Steyr Engineering AG & Co KG, Proton Motor Fuel Cell GmbH and the Vienna University of Technology, Institute for Powertrains and Automotive Technology, have developed a hydrogen-powered zero-emission vehicle within a national funded research project.

In recent years a new combustion phenomenon called Low-Speed Pre-Ignition (LSPI) occurred, which is the most important limiting factor to exploit further downsizing potential due to the associated peak pressures and thus the huge damage potential. In the past there were already several triggers for pre-ignitions identified, whereat engine oil seems to have an important influence. Other studies have reported that detached oil droplets from the piston crevice volume lead to auto-ignition prior to spark ignition. However, wall wetting and subsequently oil dilution and changes in the oil properties by impinging fuel on the cylinder wall seem to have a significant influence in terms of accumulation and detachment of oil-fuel droplets in the combustion chamber. For this reason, the influence of test fuels with different volatility were investigated in order to verify their influence on wall wetting, detachment and pre-ignition tendency.

In recent years concern has arisen over a new combustion anomaly, which was not commonly associated with naturally aspirated engines. This phenomenon referred to as Low-Speed Pre-Ignition (LSPI), which often leads to potentially damaging peak cylinder pressures, is the most important factor limiting further downsizing and the potential CO2 benefits that it could bring. Previous studies have identified several potential triggers for pre-ignition where engine oil seems to have an important influence. Many studies [1], [2] have reported that detached oil droplets from the piston crevice volume lead to auto-ignition prior to spark ignition. Furthermore, wall wetting and subsequently oil dilution [3] and changes in the oil properties by impinging fuel on the cylinder wall seem to have a significant influence in terms of accumulation and detachment of oil-fuel droplets in the combustion chamber.

This paper focuses on the potentials of a Belt-Starter-Generator (BSG) in the context of an ultra-light vehicle prototype with a target curb weight of only 600 kg. Therefore, two hybrid approaches with a voltage level below 60 V are described and their potentials regarding electrical driving and CO2 reduction are analysed in detail. Introducing the ‘Cars Ultra-Light Technology’ (CULT) project, the holistic lightweight approach is described as a main requirement for the further hybrid investigations. In addition, a P2-hybrid structure with a 12 V BSG on the transmission input shaft enabled unique features despite the low voltage level and limited electrical power resources. The CO2 reduction for this powertrain combination is described and compared to a conventional stop start configuration. The validation process on a dynamic test rig is presented as well.