Search Results

A thermo-mechanical fatigue analysis was conducted based on a coupled Finite Element Analysis (FEA) - Computational Fluid Dynamics (CFD) method on the crack failure of the exhaust manifold for an inline 4-cylinder turbo-charged diesel engine under the durability test. In the this analysis, the temperature-dependent material properties were obtained from measurements and the model was calibrated with comparison of the predicted exhaust manifold temperatures with the on-engine measurements under the same engine load condition. Temperature and stress/strain distributions in the exhaust manifold were predicted with the calibrated model. Analysis results showed that the cracks took place at locations with high plastic deformations, suggesting that the cause of the failure be thermo-mechanical fatigue (TMF). Using the equivalent plastic strain (PEEQ) as the indicator for thermal mechanical fatigue, three exhaust manifold design revisions were carried out by CAE analysis.

By means of cooperation of CAE (computer aided engineering), design and experiment, based on dynamics, combustion, fluid and finite element, respectively establish engine dynamics, combustion, fluid and finite element model, proceed innovative research on engine thermal equilibrium, cooling heat dissipation and structural strength. Through the innovation research, create the JMC top-down design and analysis process, which makes JMC product development processes have significant innovation, Independently developed engine thermal equilibrium calculation program, can positively calculate engine thermal equilibrium and water jacket cooling.

In order to better understand how the Atkinson cycle and the Miller cycle influence the fuel consumption at different engine speeds and loads, an investigation was conducted to compare influences of early intake valve closing (EIVC) and late intake valve closing (LIVC) on the fuel consumption of a 1.5L turbo-charged gasoline direct injection (TGDI) engine. The engine was tested with three different intake cams, covering three intake durations: 251 degCA (the base engine), 196 degCA (the Miller engine), and 274 degCA (the Atkinson engine). Compression ratios are 9.5:1 for the base engine and 11.4:1 for the Atkinson and Miller engines, achieved with piston modifications. Results of this investigation will be reported in three papers focusing respectively on characteristics of the engine friction, in-cylinder charge motions for different intake events, and combustion and fuel economy without and with EGR for the naturally aspirated mode and boost mode.

The present paper is Part III of an investigation on the influences of the late intake valve closing (LIVC) and the early intake valve closing (EIVC) on the engine fuel consumptions at different loads and speeds. The investigation was conducted with two 1.5L turbo-charged gasoline direct injection (TGDI) engines, one with a low-lift intake cam (the Miller engine) and the other with a high-lift intake cam (the Atkinson engine). This paper focuses on the influence of the intake-valve-closing timing on the fuel economy with and without exhaust gas recirculation (EGR). It was found that the Miller engine had a lower friction than the Atkinson engine; however, the impact of the difference in engine frictions on the fuel economy was mainly for low-speed operations. Across the engine speed range, the Miller engine had longer combustion durations than the Atkinson engine as a result of the impact of EIVC on the cylinder charge motion.

The present paper is Part II of an investigation on the influences of the late intake valve closing (LIVC) and the early intake valve closing (EIVC) on the engine fuel consumptions at different loads and speeds. The investigation was conducted with two 1.5L turbo-charged gasoline direct injection (TGDI) engines, one with a low-lift intake cam and the other with a high-lift intake cam. The focus of this paper is the cylinder charge motion. Computational fluid dynamic (CFD) analyses were conducted on the characteristics of the cylinder charge motion for the load points 6 bar-bmep / 2000 rpm, 12 bar-bmep / 3000 rpm, and 19 bar-bmep / 1500 rpm, representing naturally aspirated and boost-mode operations without and with scavenging during the valve overlap.

In order to improve low speed torques, turbocharged gasoline direct injection (TGDI) engines often employ scavenging with a help of variable valve timing (VVT) controlled by the cam phasers. Scavenging improves the compressor performance at low flows and boosts low-speed-end torques of the engines. Characteristics of the engine combustion in the scavenging zone were studied with a highly-boosted 1.5L TGDI engine experimentally. It was found that the scavenging zone was associated with the highest blowby rates on the engine map. The blowby recirculation was with heavy oil loading, causing considerable hydrocarbon fouling on the intake ports as well as on the stem and the back of the intake valves after the engine was operated in this zone for a certain period of time. The low-speed pre-ignition (LSPI) events observed in the engine tests fell mainly in the scavenging zone.

This paper reports an experimental investigation on the influence of the crankcase oil properties on the engine combustion in the low-speed pre-ignition (LSPI) zone. The investigation was conducted on a highly boosted 1.5L TGDI engine operated at the low-speed-end maximum torque, at which LSPI events were observed most frequently. Six different engine oils were tested, covering SAE 0W-20, 0W-30, 0W-40, 5W-20, 5W-30 and 5W-40. In order to evaluate the evaporative characteristics of the crankcase oil, for each of the selected engine oils, the tests were conducted at two different coolant temperatures, 90°C and 105°C. Because SAE 5W-30 was the base oil for the engine under study, for this particular oil, the investigation was extended to the impact of different levels of the mixture enrichment.

The relationship between fuel dilution of the crankcase oil and low-speed pre-ignition (LSPI) was studied experimentally with a highly-boosted 1.8L turbocharged gasoline direct injection (TGDI) engine fueled with RON93 gasoline. It was found that properties of oil particles entered the engine cylinder were affected significantly by fuel dilution. The gasoline content in the oil represents those with long carbon chain or heavy species in gasoline, with much lower boiling points and auto ignition temperatures than those for the undiluted engine oil. Thus, dilution of the engine oil by these gasoline species lowers the volatility and the minimum auto ignition temperature of the engine oil. With 15% fuel content in the oil, the flash point and the fire point of the SAE 5W30 oil dropped from 245 °C to 90 °C and from 265 °C to 150 °C, respectively.

The biggest challenge in developing Turbocharged Gasoline Direct Injection (TGDI) engines may be the abnormal combustion phenomenon occurring at low speeds and high loads, known as low-speed pre-ignition (LSPI). LSPI can trigger severe engine knocks with intensities much greater than those of spark knocks and thus characterized as super knocks. In this study, behavior and patterns of LSPI were investigated experimentally with a highly-boosted 1.5L TGDI engine. It was found that LSPI could occur as an isolated event, a couple of events in sequence, or a trail of events. Although occurring randomly among the engine cylinders, LSPI took place frequently when the engine was operated at low speeds and high loads in the zone where scavenging was employed for boosting engine torques at low speeds, typically < 2500 rpm.

Turbocharged gasoline direct injection (TGDI) engines often have a flat torque curve with the maximum torque covering a wide range of engine speeds. Increasing the high-speed-end torque for a TGDI engine provides better acceleration performance to the vehicle powered by the engine. However, it also requires more fuel deliveries and thus longer injection durations at high engine speeds, for which the multiple fuel injections per cycle may not be possible. In this study, results are reported of an experimental investigation of impact of fuel injection on dilution of the crankcase oil for a highly-boosted TGDI engine. It was found in the tests that the high-speed-end torque for the TGDI engine had a significant influence on fuel dilution: longer injection durations resulted in impingement of large liquid fuel drops on the piston top, leading to a considerable level of fuel dilution.

Turbocharged gasoline direct injection (TGDI) engines can achieve a very high level of brake mean effective pressure and thus the engines can be downsized. The biggest challenge in developing highly-boosted TGDI engines may be how to mitigate the pre-ignition (PI) triggered severe engine knocks at high loads and low engine speeds. Since magnitudes of cylinder pressure fluctuations during aforementioned engine knocks reach those for peak firing pressures in normal combustion, they are characterized as super knocks. It is widely believed that the root cause for super knocks is the oil particles entering the engine cylinder, which pre-ignite the cylinder mixture in late of the compression stroke. It is neither possible nor practical to completely eliminate the oil particles from the engine cylinder; a reasonable approach to mitigate super knocks is to weaken the conditions favoring super knocks.