Search Results

This paper presents a new magnetorheological braking which can be used in vehicles. Magneto-rheological (MR) fluid is a novel material which can be used in different components of vehicle. Magneto-rheological fluids (MRF) are suspensions of micron size whose yield stress varies rapidly as the change of magnetic field. The use of MRF in vehicles has been gaining popular recently due to its strong rheological effect, fast response and low energy consumption. Besides, these performances give designers more choice in automotive designs. However, most of the related research of MRF brake is about the construction of small prototype to verify its rheological performance. As a result, research progress is limited to calculation and simulation which make the braking force of prototype can hardly meet the requirement of vehicle due to a lack of optimal design and the understanding of MRF in the situation of high sheer stress and magnetic field.

In recent years, Magneto-rheological (MR) fluid has drawn a lot of attention for its applications in a variety of torque transmission devices, such as brakes, clutches and soft starters of mechanical equipment. Compared with the conventional clutch of vehicle, the novel MR clutch has the advantages of fast response with electronic signal, accuracy control and simple structure without mechanical wear in plates. Besides, MR clutch may be helpful to fast response of vehicle in some situation. Nowadays, most applications of MR fluids in the torque transmission field mainly are used in low-power situation. As far as we know, the proposed effective methods enhancing the output torque of MR devices will increase either the number of fluid gaps or the magnetic field in the MR fluid. This article presents a novel vehicle clutch utilizing magnetorheological fluid and multiple-disc structure.

The earth's fossil energy is not limitless, and we should be taking advantage of the highly developed fields of science and technology to utilize it more efficiently and to create a fully environmentally friendly life. Considering the prodigious amount of vehicles in the world today, even a small improvement in their energy-saving performance could have a significant impact. In this paper, a new type of electro-hydraulic power steering (EHPS) system is described. It has two main advantages. First, it can significantly decrease the demand on the motor so that it can be used for a wider range of vehicles. Second, its pressure-flow characteristic can be programmed and is more flexible than hydraulic power steering (HPS) system. A prototype with a 500 W motor was applied to a truck with a front load of 2,700 kg, and static steer sweep tests were conducted to validate its feasibility.

With the advantages of free from engine vacuum, wheel cylinder pressure decoupled from the brake pedal and can be regulated individually and precisely, the brake-by-wire system has a huge application potential in vehicles, especially in electric vehicles (EV) and hybrid electric vehicles (HEV). Electro-hydraulic Brake system is the first approach towards brake-by-wire technology. This paper proposed a new compact EHB, aiming at decreasing the size, volume and cost without compromise of performance. The main components of the proposed EHB are pedal simulator, motor pump, accumulator and eight solenoid valves. An authentic model of the EHB and other key components of the brake system were established based on the test data from the test bench. A control algorithm using Round-Robin scheduling was presented to regulate the fluid pressure. Some parameters of the components were discussed to research their effects on system performance.

The paper is focused on the research of the automotive magneto-rheological brake system whose braking force comes from the shear stress of magneto-rheological fluid under the condition of magnetic field. The MRF brake is designed for an electric passenger car to replace a conventional hydraulic disc-type brake. The braking torque of this system can be linearly adjusted by the current in just a few milliseconds with proper materials. Therefore this system has a quick response and precise control performance with a low hysteresis. Nowadays, most of the related research of MRF is about the construction of the prototype and the realization of the brake force. Main limitation of MRF brake lies in the braking torque cannot meet the actual needs and the power consumption may be too much if it is not well designed. The prototype introduced in the SAE Brake Colloquium-31nd Annual has been manufactured and assembled critically.

The four-wheel-independent Electro-hydraulic Braking system (4WI EHB) is a wet type Brake-by-Wire system for passenger vehicle and is suitable for electric vehicle (EV) and hybrid electric vehicle (HEV) to cooperate with regenerative braking. This paper gives a review on the design concepts of the 4WI EHB from the following three aspects. 1. Hydraulic architectures. 2. Design concepts of the brake actuator. 3. Installation of the components on the vehicle. Simulations and experiments are carried out to further explore the performance of hydraulic backup and implicit hardware redundancy (IHR). A method to integrate the IHR with hydraulic backup without increasing the total amount of valves is proposed, making the IHR cost and weight competitive. By reviewing various design concepts and analyzing their advantages and drawbacks, a cost and weight competitive design concept of the 4WI EHB with good fail-safe and fault-tolerant performance is proposed.

Prototype of a brake-by-wire (BBW) system named Distributed Electro-hydraulic Braking System (DEHB) has been developed. As a BBW system, DEHB is suitable to be used in electric vehicles (EV) and hybrid electric vehicles (HEV). Comparing to the ‘dry’ type distributed BBW systems such as Electro-mechanical Braking System (EMB) or Electric Wedge Brake (EWB), the ‘wet’ feature of DEHB brings benefits to system cost, installation, performance and reliability. In this paper, prototype of the DEHB was described. Based on its ‘wet’ feature, a new fail-safe control for DEHB was proposed. Two types of DEHB architectures that can perform the proposed fail-safe control were described. Superiority of the proposed fail-safe control and architectures for DEHB were examined and verified through simulations and HIL experiments, which helps DEHB to reach a high level of safety and reliability with reduced cost on electro/electronic redundancy.

The paper presents a new electromechanical brake system for vehicles using magnetorheological fluid. The brake system designed for the electric vehicle has some advantages over the conventional brake system. The brake system is made up of a brake disk, shells, magnetorheological fluid (MRF) and the electromagnets. The brake disk is immersed in the MRF whose yield stress changes as the applied magnetic field. The braking torque of this system can be linearly adjusted by the current in just a few milliseconds without the conventional vacuum booster. This system has a quick response and precise control performance with a low hysteresis. Besides, the system has adopted the original complicated structure to save space and cost. In this paper, the configuration of MRF brake types is described. The braking torques of the MRF brakes is derived based on the MRF theoretical model which is firstly raised. Some braking simulation based on the theoretical model is also shown.