Search Results

Although in the latest years the use of compression ignition engines has been a thread of discussion in the automotive field, it is possible to affirm that it still will be a fundamental producer of mechanical power in other sectors, such as naval and off-road applications. However, the necessity of reducing emissions requires to keep on studying new solutions for this kind of engine. Dual fuel combustion concept with methane has demonstrated to be effective in preserving the performance of the original engine and reducing soot, but issues related to the low flame speed forced researcher to find an alternative fuel at low impact of CO2. Hydrogen, thanks to its chemical and physical properties, can be a perfect candidate to ensure a good level of combustion efficiency; however, this is possible only with a proper management of the in-cylinder mixture ignition by means of a pilot injection, preventing uncontrolled autoignition events as well.

Nowadays, the stricter regulations in terms of emissions have limited the use of diesel engines on urban roads. On the contrary, for marine and off-road applications the diesel engine still represents the most feasible solution for work production. In the last decades, dual fuel operation with methane supply has been widely investigated. Starting from previous studies on a research engine, where diesel-methane dual fuel combustion has been deepened both experimentally and numerically with the aid of a CFD code, the authors implemented and tested a kinetic mechanism. It is obtained from the combination of the well-established GRIMECH 3.0 and a detailed scheme for a diesel surrogate oxidation. Moreover, the Autoignition-Induced Flame Propagation model, included in the ANSYS Forte® software, is applied because it can be considered the most appropriate model to describe dual fuel combustion.

Methane supply in diesel engines operating in dual fuel mode has demonstrated to be effective for the reduction of particulate matter and nitric oxides emissions from this type of engine. In particular, methane is injected into the intake manifold to form a premixed charge with air, while a reduced amount of diesel oil is still directly injected to ignite the mixture inside the cylinder. As a matter of fact, the liquid fuel burns following the usual diffusive combustion, so activating the gaseous fuel oxidation in a premixed flame. Clearly, the whole combustion process appears to be more complex to be described in a CFD simulation, mainly because it is not always possible to select in the 3-dimensional codes a different combustion model for each fuel and, also, because other issues arise from the interaction of the two fuels.

Engine downsizing has established itself as one of the most successful strategies to reduce fuel consumption and pollutant emissions in the automotive field. To this regard, a major role is played by turbocharging, which allows an increase in engine power density, so reducing engine size and weight. However, the need for turbocharging imposes some issues to be solved. In the attempt of mitigating turbo lag and poor low-end torque, many solutions have been presented in the open literature so far, such as: low inertia turbine wheels and variable geometry turbines; or even more complex concepts such as twin turbo and electrically assisted turbochargers. None of them appears as definitive, though. As a possible way of reducing turbine rotor inertia, and so the turbo lag, also the change of turbine layout has been investigated, and it revealed itself to be a viable option, leading to the use of mixed-flow turbines.

This paper deals with the experimental and numerical investigation of a 2.0 litre single cylinder Heavy Duty Diesel Engine fuelled by natural gas and diesel oil in Dual Fuel mode. Due to the gaseous nature of the main fuel and to the high compression ratio of the diesel engine, reduced emissions can be obtained. An experimental study has been carried out at three different load level (25%, 50% and 75% of full engine load). Basing on experimental data, the authors recreated a 45° mesh sector of the engine cylinder and performed CFD simulations for the cases at 50% and 75% load levels. Numerical simulations were carried out on the 3D code Ansys FORTE. The aim of this work is to study combustion phenomena and, in particular, the interaction between natural gas and diesel oil, respectively represented by methane and n-dodecane. A reduced kinetic scheme for methane auto-ignition was implemented while for n-dodecane two set of reactions were utilised.

The modern automotive industry is under strict regulations to reduce emissions to comply with the Kyoto Protocol, a universally acknowledged treaty aiming at reducing exhaust gas emissions. In order to achieve the required future emission reduction targets, further developments on gasoline engines are required. One of the main methods to achieve this goal is the application of engine downsizing. Turbocharging is a cost-effective method of downsizing an engine whilst reducing exhaust gas emissions, reducing fuel consumption and maintaining prior performance outputs. For these reasons, the turbocharging is becoming the most widely adopted technology in the automotive markets. In 2012, 32% of passenger and commercial vehicles sold had a turbocharger installed, and is predicted to be 40% of 2017 [1]. Even if the engine turbocharging is a widespread technology, there are still drawbacks present in current turbocharging systems.

The dual-fuel (diesel/natural gas, NG) concept represents a solution to reduce emissions from diesel engines by using natural gas as an alternative fuel. As well known, the dual-fuel technology has the potential to offer significant improvements in the emissions of carbon dioxide from light-duty compression ignition engines. A further important requirement of the DF operation in automotive engines is a satisfactory response in a wide range of load levels. In particular, the part-load levels could present more challenging conditions for an efficient combustion development, due to the poor fuel/air ratio. Basing on the above assumptions, the authors discuss in this article the results of a combined numerical and experimental study on the effect of different injection timings on performance and pollutant fractions of a common rail diesel engine supplied with natural gas and diesel oil.