Search Results

As passenger cars are progressively moving towards more electrification, Plug-in Hybrid Electric Vehicles (PHEVs) may play a greater role. Several questions arise regarding their performance in real-world conditions, their optimal configuration - in terms of battery capacity, fuel and powertrain used - and their pollutant emissions. In this context, two PHEVs complying with Euro 6d standards were evaluated on a chassis-dyno and on-road using the same road profile, complying with RDE requirements. The two vehicles differ only by their powertrain, one being diesel-fueled, and the other being gasoline-fueled. The vehicles were tested under various conditions, including charge depleting and charge sustaining modes (i.e., tests respectively starting with a fully charged battery and a discharged battery), with various fuel compositions including traditional fossil-based fuels, 100% renewable Hydrotreated Vegetable Oil (HVO) and 100% renewable gasoline, blended with 20% v/v ethanol (E20).

Since 2019 in-service conformity testing for vehicles as described in EU legislation 2018/1832 is active and obliges numerous emission control tests on WLTP and RDE cycles. For the on-road portion of these tests typically Portable Emissions Measurement System (PEMS) are used. While these systems provide all necessary regulated emissions measurements, their use and handling are difficult due to their weight, cumbersome installation, and their limited accessibility due to a high price point. In order to make the real-driving measurement accessible for a maximum number of institutions, IFPEN is developing a compact measurement system with an advanced cloud modeling of the vehicle for more cost-effective and user friendly RDE and ISC testing. This real-time analyzer, named “REAL-e” is developed as an IoT system, who’s measured data is transferred in real-time to a secured cloud service for enhanced data processing and data enrichment.

Recent work has demonstrated the potential of gasoline-like fuels to reduce NOx and particulate emissions when used in compression ignition engines. In this context, low research octane number (RON) gasoline, a refinery stream derived from the atmospheric crude oil distillation process, has been identified as a highly valuable fuel. In addition, thanks to its higher H/C ratio and energy content compared to diesel, CO2 benefits are also expected when used in such engines. In previous studies, different cetane number (CN) fuels have been evaluated and a CN 35 fuel has been selected. The assessment and the choice of the required engine hardware adapted to this fuel, such as the compression ratio, bowl pattern and nozzle design have been performed on a single cylinder compression-ignition engine.

Reducing the CO2 footprint, limiting the pollutant emissions and rebalancing the ongoing shift demand toward middle-distillate fuels are major concerns for vehicle manufacturers and oil refiners. In this context, gasoline-like fuels have been recently identified as good candidates. Straight run naphtha, a refinery stream derived from the atmospheric crude oil distillation process, allows for a reduction of both NOx and particulate emissions when used in compression-ignition engines. CO2 benefits are also expected thanks to naphtha’s higher H/C ratio and energy content compared to diesel. In previous studies, wide ranges of Cetane Number (CN) naphtha fuels have been evaluated and CN 35 naphtha fuel has been selected. The assessment and the choice of the required engine hardware adapted to this fuel, such as the compression ratio, bowl pattern, nozzle design and air-path technology, have been performed on a light-duty single cylinder compression-ignition engine.

The more and more severe regulations on exhaust emissions from vehicles and the worldwide demand for fuel consumption reduction impose continuous improvements of the engine thermal efficiency. Base engine geometrical setups are important aspects which have to be taken into account to improve the engine efficiency. This paper discusses the influence of the bore-to-stroke ratio on emissions, fuel consumption and full load performances of a Diesel engine. The expected advantage of a reduced bore-to-stroke ratio is mainly a decrease of the thermal losses, due to a higher volume-to-surface ratio, reducing the wall surfaces, responsible for the heat losses, per volume of gas. The advantages concerning the wall heat losses are opposed to the disadvantages of lower volumetric efficiency, as a smaller bore requires smaller valve diameter. Additionally does a reduction of the bore-to-stroke ratio lead to an increase of the friction losses, as the mean piston speed increases.