Search Results

Reaching near-zero cold start emissions in a wide range of ambient conditions is a challenging, yet necessary objective. Optimizing the combustion, although fundamental to lower specific engine-out emissions, is not sufficient, especially in high-performance engines. A very high after-treatment efficiency from engine start-up onwards is mandatory. Active heating technologies allow quick heating up of after-treatment devices like a three way catalyst above their light-off temperature, regardless of engine operation. In this work, the particular characteristics of a fuel burner were analyzed. The steps that led to the design of an exhaust system equipped with a fuel burner are reported. The fuel burner ability to efficiently heat up after-treatment devices was assessed by numerical simulations and then verified experimentally. Cumulative results were compared with a passive catalyst heating strategy.

The reduction of the catalyst light-off time at the engine cold start represents a key factor for the pollutant emissions control from vehicles tested on homologation cycles and real drive conditions. The adoption of heating strategies to increase the temperature of the catalytic substrate in the early phase of the engine start is regarded as a promising solution. The present study focuses on the application of electrical heated catalyst (EHC) in an after-treatment line for a spark-ignition gasoline engine. The analysis is carried out by means of an advanced CFD framework, which includes the modeling of catalytic reactions in the substrates and accounts for the thermal evolution of all the components included in the after-treatment system.

In the next years, the upcoming emission legislations are expected to introduce further restrictions on the admittable level of pollutants from vehicles measured on homologation cycles and real drive tests. In this context, the strict control of pollutant emissions at the cold start will become a crucial point to comply with the new regulation standards. This will necessarily require the implementation of novel strategies to speed-up the light-off of the reactions occurring in the after-treatment system, since the cold start conditions are the most critical one for cumulative emissions. Among the different possible technological solutions, this paper focuses on the evaluation of the potential of a burner system, which is activated before the engine start. The hypothetical burner exploits the lean combustion of an air-gasoline mixture to generate a high temperature gas stream which is directed to the catalyst section promoting a fast heating of the substrate.

In recent times, complying with increasingly stringent emission regulations has become ever more challenging than before. While an efficient after-treatment system, that includes a gasoline particulate filter, enables compliance with legislation requirements, lowering engine-out emissions by improving the combustion system must be considered as a crucial advantage for both pollutants emission control and performance. In this respect, high-performance enabling contents such as relatively large displacement, flow-capacity oriented intake ports and a limited stroke-to-bore ratio have significant drawbacks on the charge motion quality and, consequently, on mixture formation and homogeneity. As a countermeasure, fuel injection system components, as well as control strategies, need to be substantially improved.

This paper presents the modeling of the transient phase of catalyst heating on a high-performance turbocharged spark ignition engine with the aim to accurately predict the exhaust thermal energy available at the catalyst inlet and to provide a “virtual test rig” to assess different design and calibration options. The entire transient phase, starting from the engine cranking until the catalyst warm-up is completed, was taken into account in the simulation, and the model was validated using a wide data-set of experimental tests. The first step of the modeling activity was the combustion analysis during the transient phase: the burn rate was evaluated on the basis of experimental in-cylinder pressure data, considering both cycle-to-cycle and cylinder-to-cylinder variations.

Measurement of particle number was introduced in the Euro 5/6 light duty vehicle emissions regulation. Due to the complex nature of combustion exhaust particles, and to transportation, transformation and deposition mechanisms, such type of measurement is particularly complex, and regression analysis is commonly used for the comparison of different measurement systems. This paper compares various commercial instruments, developing a correlation analysis focused on PN (Particle Number) measurement, and isolating the factors that mainly influence each measuring method. In particular, the experimental activity has been conducted to allow critical comparisons between measurement techniques that are imposed by current regulations and instruments that can be used also on the test cell. The paper presents the main results obtained by analyzing instruments based on different physical principles, and the effects of different sampling locations and different operating parameters.

Recent engine development has been mainly driven by increased specific volumetric power and especially by fuel consumption minimization. On the other hand the stringent emission limits require a very fast cold start that can be reached only using tailored catalyst heating strategy. This kind of thermal management is widely used by engine manufactures although it leads to increased fuel consumption. This fuel penalty is usually higher for high power output engines that have a very low load during emission certification cycle leading to very low exhaust gas temperature and, consequently, the need of additional energy to increase the exhaust gas temperature is high. An alternative way to reach a fast light off minimizing fuel consumption increase is the use of an Electrical Heated Catalyst (EHC) that uses mechanical energy from the engine to generate the electrical energy to heat up the catalyst.