Search Results

The electrification of powertrains provides a critical opportunity to change the way that engines are designed and developed, allowing their efficiency to be increased and their cost reduced. This paper draws on ongoing Ricardo projects in the field of dedicated hybrid engines (DHEs). The Magma xEV combustion concept employs very high compression ratio, long stroke architecture, and advanced ignition and knock mitigation technologies, for DHEs requiring the highest efficiency. In the latest research project a pre-chamber combustion system (with both active and passive operation) has been applied to the Magma xEV engine, in order to enable the highest levels of charge dilution and further increase brake thermal efficiency. The research focussed on benefits of pre-chamber ignition as compared to conventional spark ignition and corona discharge ignition. The comparison of charge dilution using excess air (lean operation) and exhaust gas recirculation are presented.

This paper presents the summary of the development of a two-phase spray model of a hollow-cone fuel injector commonly applied to spray-guided, gasoline direct injection, (SGDI) engines. The model was simulated using the Ricardo VECTIS CFD code and takes into account the physical and chemical effects of oxygenated fuel blends (flexfuels). The characteristics of the fuel sprays at typical gasoline part-load conditions, identified in a parallel study, were of particular interest. An injection duration of 0.3 ms was chosen which represented a stratified charge, unthrottled, part-load operating condition in a spray guided GDI engine with a piezoelectric fuel injector and a fuel injection pressure of 200 bar gauge. In the first instance, the spray model was validated against data recorded in a constant volume spray chamber. Secondly, the robustness of the model was tested against data measured in an optically-accessed engine.

Compared to conventional homogeneous direct injection or port-fuel injected engines, the second generation, spray guided, direct injection engine (SGDI) has the potential for significantly improved fuel economy during part load stratified charge operation. Multiple fuel injection strategies can be utilised to increase the unthrottled operating range, leading to further improvements in fuel economy. However, careful optimisation of these strategies is essential to ensure that benefits are maintained whilst further minimising emissions within combustion stability limits and consumer driveability demands. The effects of multiple injection strategies upon fuel consumption, emissions and combustion stability were investigated in a single cylinder Ricardo Hydra engine with a spray guided combustion system. An outwardly opening piezoelectric actuated injector was employed. The fuel injection strategy utilised up to five injections per engine cycle.

The 2/4SIGHT engine concept is based on a novel design of combustion system, which makes use of an electric-hydraulic valvetrain and advanced control technologies, enabling automatically controlled dynamic switching of the engine between two- and four-stroke operations. This concept has the potential to improve fuel consumption by up to 30% compared to a conventional gasoline engine. A 3 cylinder GDI engine with two stage boosting system and electro-hydraulic valvetrain is the main application for this project, with 6 cylinder application being studied in simulation. The design of a Control System poses several challenges due to the simultaneous introduction of several innovations such as advanced boost system, electro-hydraulic valvetrain system and two/four stroke operating mode. In order to develop and optimise the design of the control system, an integrated simulation environment has been developed.

This paper describes the results of the first stage of an integrated experimental and modelling programme on a gasoline engine with Twin Mechanical Variable Lift (TMVL) capability. The engine used for this work was a modified version of a 4 cylinder, 2.0 litre BMW engine. The modified engine has the “Valvetronic” continuously variable lift valvetrain on both the inlet and exhaust valves and dual independent cam phasers with 60 crankshaft degrees of phasing authority. The Valvetronic system allows continuous variation of the valve lift from a minimum of 0.25 mm to a maximum of 9.7 mm.

The pursuit of flexibility is a recurring theme in engine design and development. Engines that are able to switch between the two-stroke operating cycle and four-stroke operation promise a great leap in flexibility. Such 2S-4S engines could then continuously select the optimum operating mode - including HCCI/CAI combustion - for fuel efficiency, emissions or specific output. With recent developments in valvetrain technology, advanced boosting devices, direct fuel injection and engine control, the 2S-4S engine is an increasingly real prospect. The authors have undertaken a comprehensive feasibility study for 2S-4S gasoline engines. This study has encompassed concept and detailed design, design analysis, one-dimensional gas dynamics simulation, three-dimensional computational fluid dynamics, and vehicle simulation. The resulting 2/4SIGHT concept engine is a 1.04 l in-line three-cylinder engine producing 230 Nm and 85 kW.

Reducing engine swept volume (so-called ‘downsizing’) offers the potential to meet future tighter CAFÉ standards and reduced CO2 vehicle emissions in Europe. In downsizing the gasoline engine, a key challenge is controlling octane requirement without sacrificing fuel economy. The authors have investigated five alternative approaches on a turbocharged DI gasoline engine: Conventional stoichiometric operation, with reduced compression ratio (CR) Lean Boost DI (LBDI) with lean operation at full-load to control octane requirement while maintaining a high CR EGR Boost with cooled EGR dilution rather than excess air to control octane requirement Miller cycle concept, where valve-timing strategies are employed to reduce the effective compression ratio at high load Dual injection strategies to control octane requirement Each approach has been investigated using engine performance and vehicle simulation codes.

This paper describes a two-year programme of research conducted by the authors investigating HCCI in direct injection gasoline engines. Poppet-valved two-stroke cycle operation has been investigated experimentally, using conventional gasoline compression ratios and fuel, and ambient temperature intake air. Extensive combustion and emissions data was gathered from the experimental engine. Computational Fluid Dynamics (CFD) has been used to model HCCI combustion, and the CFD tool validated using experimental data. Based on experience with the two-stroke engine and modelling techniques, a four-stroke engine has been designed and tested. Using this range of tools, practical options for gasoline HCCI engines are evaluated, and a scenario for the market introduction of HCCI is presented.

For optimum efficiency, the direct injection (DI) gasoline engine requires two operating modes to cover the full load/speed map. For lower loads and speeds, stratified charge operation can be used, while homogeneous charge is required for high loads and speeds. This paper has focused its attention on the latter of these modes, where the performance is highly dependent on the quality of the fuel spray, evaporation and the air-fuel mixture preparation. Results of quantitative and qualitative Laser Induced Fluorescence (LIF) measurements are presented, together with shadow-graph spray imaging, made within an optically accessed DI gasoline engine. These are compared with previously acquired air flow measurements, at various injection timings, and with engine performance and emissions data obtained in a fired single cylinder non-optical engine, having an identical cylinder head and piston crown geometry.

This paper describes the Lean Boost System, a gasoline engine concept for improved fuel economy. The system combines direct injection, lean operation and pressure charging, and allows significant reduction in swept volume, or ‘downsizing’. Engine tests have been undertaken which demonstrate the validity of the combustion concept. The strategy a typical manufacturer might adopt in order to meet future European requirements for CO2 emissions is proposed. Vehicle simulation results for typical North American and European vehicles are presented. Using the exhaust gas emission levels from engine tests and drive cycle simulation, aftertreatment requirements and configurations are considered.

The need to reduce fuel consumption and CO2 emissions while meeting future emission legislation has lead to the investigation of alternative engines, transmissions, aftertreatment and control strategies. The evaluation of alternative configurations at the concept stage requires vehicle drive cycle simulation tools, which include the following features: Fast run-time Alternative transmission models Cold start effects on fuel consumption and emissions modeled After-treatment models. This paper describes the development of a MATLAB/SIMULINKTM - based drive cycle simulation model meeting these requirements. The paper includes validation data comparing fuel consumption, engine-out and tailpipe emissions for a direct injection gasoline vehicle with a stoichiometric/lean switching strategy and lean NOx catalyst.

The performance of a direct injection gasoline engine (G-DI) is highly dependent on the quality of the air-fuel mixture preparation. This is of particular importance when operating at a stratified charge condition, where the ideal mixture distribution would be a stoichiometric region around the spark plug, surrounded by air. To achieve this ideal situation over a wide range of speeds and loads is extremely difficult, requiring an understanding of the fuel spray, the in-cylinder air motion and their interactions. This paper presents the results of Phase Doppler Anemometry (PDA) and Laser Induced Fluorescence (LIF) measurements made both within an optically accessed direct injection gasoline engine and under atmospheric conditions. The experimental results are compared with those of a VECTIS Computational Fluid Dynamics (CFD) simulation of the same engine.