Search Results

Energy security and climate change challenges provide a strong impetus for investigating Electric Vehicle (EV) concepts. EVs link two major infrastructures, the transportation and the electric power grid. This provides a chance to bring other sources of energy into transportation, displace petroleum and, with the right mix of power generation sources, reduce CO₂ emissions. The main obstacles for introducing a large numbers of EVs are cost, battery weight, and vehicle range. Battery health is also a factor, both directly and indirectly, by introducing limits on depth of discharge. This paper considers a low-cost path for extending the range of a small urban EV by integrating a parallel hydraulic system for harvesting and reusing braking energy. The idea behind the concept is to avoid replacement of lead-acid or small Li-Ion batteries with a very expensive Li-Ion pack, and instead use a low-cost hydraulic system to achieve comparable range improvements.

This work presents a method for simultaneously capturing visible and infrared images along with pressure data in an optical Diesel engine based on the International 4.5L VT275 engine. This paper seeks to illustrate the merits of each imaging technique for visualizing both in-cylinder fuel spray and combustion. The engine was operated under a part load, high simulated exhaust gas recirculation operating condition. Experiments examining fuel spray were conducted in nitrogen. Overlays of simultaneously acquired infrared and visible images are presented to illustrate the differences in imaging between the two techniques. It is seen that the infrared images spatially describe the fuel spray, especially fuel vapors, and the fuel mixing process better than the high-speed visible images.

A hydraulic free-piston engine (FPE), which converts combustion energy directly to hydraulic energy, is being developed by the U. S. EPA due to its potential as a lower-cost and higher-efficiency prime mover for hydraulic series hybrid vehicles. Two prototype engines were designed, fabricated and tested: a two-cylinder engine operating primarily with a two-stroke compression-ignition, direct-injection (CIDI) cycle and a six-cylinder engine operating with a four-stroke CIDI cycle. These engines successfully achieved up to 39% peak hydraulic efficiency under continuously fired operation, while demonstrating exceptional repeatability and control of the cylinder compression ratio. A basic description of the engine design, along with the initial test results from these two prototypes, is presented below.

Three-dimensional numerical simulations of a diesel-fueled engine with a pre-chamber located in the cylinder head and a bowl in the piston were performed. The study considers the effect of diesel combustion in the pre-chamber on turbulence generation and hence fuel-air mixing and combustion in the piston-bowl. Diesel fuel was injected directly into the pre-chamber and the piston bowl at different times. In order to better determine the effect of pre-chamber combustion on the main chamber combustion, various pre-chamber injection timings were considered. The results show that pre-chamber combustion caused the average cylinder pressure to increase by up to 20% in some cases.

Homogenous charge compression ignition (HCCI) engines offer a great potential in achieving high thermal efficiency and extremely low NOx at the same time. However, control of combustion phasing over a wide speed and load range has been a challenge, especially during transient operations. This paper describes work conducted at the National Vehicle and Fuel Emissions Laboratory, which explores the potential use of an HCCI engine as a power plant for a hybrid vehicle. A four-cylinder, 1.9 L commercial diesel engine was modified to operate with port-injected regular grade gasoline in HCCI mode. The combustion phasing is controlled by a combination of boost, EGR and thermal management as a function of engine speed and load. As a stand-alone unit, the engine has demonstrated a wide operation range with efficiency like that of a diesel engine and NOx below 0.2 g/kWh. At room temperature, the engine starts in SI mode and then transitions to HCCI in about 25 seconds.

Three-dimensional transient simulations using KIVA-3V were conducted on a 4-stroke high-compression ratio, methanol-fueled, direct-injection (DI) engine. The engine had two intake ports that were designed to impart a swirling motion to the intake air. In some cases, the intake system was modified, by decreasing the ports diameter in order to increase the swirl ratio. To investigate the effect of adding shrouds to the intake valves on swirl, two sets of intake valves were considered; the first set consisted of conventional valves, and the second set of valves had back shrouds to restrict airflow from the backside of the valves. In addition, the effect of using one or two intake ports on swirl generation was determined by blocking one of the ports.

Numerical simulations of lean Methanol combustion in a four-stroke internal combustion engine were conducted on a high-compression ratio engine. The engine had a removable integral injector ignition source insert that allowed changing the head dome volume, and the location of the spark plug relative to the fuel injector. It had two intake valves and two exhaust ports. The intake ports were designed so the airflow into the engine exhibited no tumble or swirl motions in the cylinder. Three different engine configurations were considered: One configuration had a flat head and piston, and the other two had a hemispherical combustion chamber in the cylinder head and a hemispherical bowl in the piston, with different volumes. The relative equivalence ratio (Lambda), injection timing and ignition timing were varied to determine the operating range for each configuration. Lambda (λ) values from 1.5 to 2.75 were considered.

A stratified charge research engine and test stand were designed and built for this work. The engine was designed to exhibit some of the desirable traits of both the premixed charge gasoline engine and modern diesel engine. This spark ignition engine is fueled by M100 (99.99% pure methanol), operates under high compression (19.3:1) and uses direct fuel injection to form a stratification of the fuel-air mixture in the cylinder. The beginning of the combustion event of the stratified mixture is triggered by spark plug discharge. The primary goal of this project was to evaluate the feasibility of using a removable integral injector ignition source insert, which allows a convenient method of changing the relative location of the fuel injector to the ignition source, as well as the compression ratio, squish height, and bowl volumes. This paper provides an explanation of the hardware included in the experimental setup of the engine and selection of the direct injector configuration.