Refine Your Search

Search Results

Viewing 1 to 5 of 5
Journal Article

HEV Battery Pack Thermal Management Design and Packaging Solutions

2017-03-28
2017-01-0622
Hybrid Electric Vehicles (HEV) utilize a High Voltage (HV) battery pack to improve fuel economy by maximizing the capture of vehicle kinetic energy for reuse. Consequently, these HV battery packs experience frequent and rapid charge-discharge cycles. The heat generated during these cycles must be managed effectively to maintain battery cell performance and cell life. The HV battery pack cooling system must keep the HV battery pack temperature below a design target value and maintain a uniform temperature across all of the cells in the HV battery pack. Herein, the authors discuss some of the design points of the air cooled HV battery packs in Ford Motor Company’s current model C-Max and Fusion HEVs. In these vehicles, the flow of battery cooling air was required to not only provide effective cooling of the battery cells, but to simultaneously cool a direct current high voltage to low voltage (DC-DC) converter module.
Technical Paper

Factors Influencing Liquid over Air Cooling of High Voltage Battery Packs in an Electrified Vehicle

2017-03-28
2017-01-1171
Automotive vehicle manufactures are implementing electrification technologies in many vehicle line-ups to improve fuel economy and meet emission standards. As a part of electrification, High Voltage (HV) battery packs are integrated alongside internal combustion engines. Recent generation HV batteries allow extensive power usage, by allowing greater charge and discharge currents and broader State of Charge (SOC) ranges. Heat generated during the charge-discharge cycles must be managed effectively to maintain battery cell performance and life. This situation requires a cooling system with higher efficiency than earlier generation electrified powertrains. There are multiple thermal solutions for cooling HV battery packs including forced air, liquid, direct refrigerant, and passive cooling. The most common types of HV battery pack cooling, for production vehicles, are air cooled using cabin interior air and liquid cooled using powertrain cooling systems.
Technical Paper

Safe Practices and Procedures for High Voltage and Hydrogen in Ford's H2RV

2004-03-08
2004-01-0059
In recent times, the development of alternate-fuel vehicles, including those fueled by hydrogen, has become relatively common. While there are potential safety related issues with any combustible fuel, these have been resolved over the last 100+ years. The comfort level with gasoline fuel has resulted from the widespread application of simple safety procedures followed at every stage of gasoline refinement and handling. It is important to have analogous procedures for handling hydrogen-fueled vehicles safely and with confidence. The characteristics of hydrogen, including: a) wide flammability range, b) very low ignition energy, c) odorless and difficult to detect, d) high diffusion rate, e) high buoyancy, f) invisible flame, etc., bolster the need for safe practices and procedures.
Technical Paper

Architecture and Development of a Hydrogen Sensing and Mitigation System in H2RV - Ford's Concept HEV Propelled With a Hydrogen Engine

2004-03-08
2004-01-0359
Ford's Hydrogen Hybrid Research Vehicle (H2RV) is an industry first parallel hybrid vehicle utilizing a hydrogen internal combustion engine. The goal of this drivable concept vehicle is to marry Ford's extensive hybrid powertrain experience with its hydrogen internal combustion engine technology to produce a low emission, fuel-efficient vehicle. This vehicle is seen as a possible bridge from the petroleum fueled vehicles of today to the fuel cell vehicles envisioned for tomorrow. A multi-layered hydrogen management strategy was developed for the H2RV. All aspects of the vehicle including the design of the fuel and electrical systems, placement of high-voltage subsystems, and testing, service, and storage procedures were examined to ensure the safe operation of the vehicle. The results of these reviews led to the design of the hydrogen sensing and mitigation system for the H2RV vehicle.
Technical Paper

Architectural Challenges of an Electrical Distribution System in Prototype HEVs

2003-03-03
2003-01-0094
Hybrid Electric Vehicle (HEV) prototypes are based off production platforms. Several new systems are added to the vehicle, either to perform hybrid functions or to support them and enhance vehicle performance and fuel economy. All these systems are electrically connected in the vehicle with overlay wiring harnesses. Architecture of overlay wiring harness for the HEV requires identification of new systems and working out their electrical connectivity requirements. This dictates the level of changes required in the vehicle electrical system. Harnesses are built based on the circuit design and location of these systems in the vehicle. EMI requirements, routing and packaging challenges are resolved during the overlay process and testing of the prototype. This paper presents the process of harness design, its architecture and integration challenges in the vehicle.
X