Search Results

In this study, tailpipe-sampling was used to sample the exhaust aerosol of a Stage IV tractor equipped with Diesel Oxidation Catalyst (DOC) and Selective Catalytic Reduction (SCR) aftertreatment systems. The particle emissions were characterized in terms of number concentration (particle size of > 2.5 nm), mass concentration (particle size of 6-612 nm) BC mass concentration and chemical composition (particle size of > 30 nm). The measurements were conducted on-road by setting a mobile laboratory on a trailer and pulling it with the tractor. In addition to driving, heavy-lift work cycles were tested, where separate lifts of a 1000 kg weight were conducted with the front fork of the tractor with two minutes of idling between consecutive lifts. Both a Porous Tube Diluter (PTD) with ambient temperature dilution air as well as an ejector diluter with hot dilution air were used to sample the exhaust aerosol.

Under on-road driving conditions, the engine load and speed and the cooling effect of ambient air may affect the functioning of exhaust aftertreatment devices. In this paper, we studied the effects of these parameters on the functioning of the combination of a Diesel Oxidation Catalyst and a Particle Oxidation Catalyst (DOC+POC). In the engine tests, the engine load and speed were observed to affect the nonvolatile particle reduction efficiency curve of the DOC+POC; while the nonvolatile core particle (Dp ≺ 15 nm) reduction was high (97-99%) in all the engine test modes, the reduction of soot varied from 57% at low load to 70% at high load. Because the change in engine load and speed affected both the exhaust temperature and flow velocity, the effects of these parameters were measured separately in an aerosol laboratory.

During the past few decades the exhaust emissions of diesel engines have significantly decreased due to efficient emissions regulation. Compared to the situation in the 1990s, the nitrogen oxide (NOx) and particulate matter (PM) emissions, the main challenges for diesel engines, are now reduced 80-95 % in many industrialized countries. To meet the demanding requirements, engine technologies have been updated and improved step by step. These improvements have also kept Specific Fuel Consumption (SFC) figures at a low level or they have even improved. The latter issue is of great significance for consumers (cost) and also for the environment (CO2). Nowadays many diesel engine fuel injection strategies rely on the use of exhaust after-treatment systems. Efficient and clean combustion is obtained by utilizing high injection pressure and advanced injection timing.

A modern diesel engine is a reliable and efficient mean of producing power. A way to reduce harmful exhaust and greenhouse gas (GHG) emissions and secure the sources of energy is to develop technology for an efficient diesel engine operation independent of fossil fuels. Renewable diesel fuels are compatible with diesel engines without any major modifications. Rapeseed oil methyl esters (RME) and other fatty acid methyl esters (FAME) are commonly used in low level blends with diesel. Lately, hydrotreated vegetable oil (HVO) produced from vegetable oil and waste fat has found its way into the automotive market, being approved for use in diesel engines by several leading vehicle manufacturers, either in its pure form or in a mixture with the fossil diesel to improve the overall environmental footprint. There is a lack of data on how renewable fuels change the semi-volatile organic fraction of exhaust emissions.

The aim of this paper is to analyze the quantitative impact of fuel sulfur content on particulate oxidation catalyst (POC) functionality, focusing on soot emission reduction and the ability to regenerate. Studies were conducted on fuels containing three different levels of sulfur, covering the range of 6 to 340 parts per million, for a light-duty application. The data presented in this paper provide further insights into the specific issues associated with usage of a POC with fuels of higher sulfur content. A 48-hour loading phase was performed for each fuel, during which filter smoke number, temperature and back-pressure were all observed to vary depending on the fuel sulfur level. The Fuel Sulfur Content (FSC) affected also soot particle size distributions (particle number and size) so that with FSC 6 ppm the soot particle concentration was lower than with FSC 65 and 340, both upstream and downstream of the POC.

The effect of SCR on nanoparticle emissions has been a subject for some recent diesel particle emission related studies. In this study, the effect of after-treatment (DOC and SCR) on particle emissions was studied with a heavy-duty off-road diesel engine (emission level stage 3b with an SCR). A special “transient cold test cycle” (TCTC) was designed to describe the SCR system operation at low exhaust gas temperatures. The particle instrumentation made it possible to measure on-line the particle number concentration, particle size distribution and chemical composition of particles. The largest particle number concentrations were measured after the exhaust manifold. The exhaust after-treatment was observed to reduce the total particle number concentration by 82.5% with the DOC and 95.7% with the DOC+SCR.

Particle number emissions from an off-road diesel engine without exhaust after-treatment were studied by using five different heavy-duty lubricating oils in the engine. The study extends understanding on how the properties of lubricating oil affect the nanoparticle emissions from an off-road diesel engine. The lubricants were selected among the performance classes of the European Automobile Manufacturers Association, at least one lubricant from each category intended for heavy-duty diesel engines. Particle size distributions were measured by the means of an engine exhaust particle sizer (EEPS), but soot emissions, gaseous emissions and the basic engine performance were also determined. During the non-road steady state cycle, the most of the differences were detected at the particle size range of 6-15 nm. In most cases, the lowest particle quantities were emitted when the highest performance category lubricant was used.

Particle emissions have been generally associated to diesel engines. However, spark-ignition direct injection (SI-DI) engines have been observed to produce notable amounts of particulate matter as well. The upcoming Euro 6 legislation for passenger cars (effective in 2014, stricter limit in 2017) will further limit the particulate emissions from SI engines by introducing a particle number emission (PN) limit, and it is not probable that the SI-DI engines are able to meet this limit without resorting to additional aftertreatment systems. In this study, the solid particle emissions of a SI-DI passenger car with and without an installed Particle Oxidation Catalyst (POC®) were studied over the New European Driving Cycle (NEDC) on a chassis dynamometer and over real transient acceleration situations on road. It was observed that a considerable portion of particle number emissions occurred during the transient acceleration phases of the cycle.

Particle Number (PN) measurement testing has for long been conducted by using Condensation Particle Counter (CPC) based technology. While accurate at low concentrations, CPC has nevertheless several drawbacks for in-field use, such as the use of a working fluid, the need for dilution, the delicate optical components and the sensitivity to contamination. Diffusion Charging (DC) based particle counting technologies have often been disregarded as a valid alternative to CPC based methods due to their intrinsic particle size dependent counting efficiency and lower sensitivity. However, Dekati’s novel ePNC PN technology has brought DC technology to the next level.