Search Results

The environmental and sustainable energy concerns in transport are being addressed through the decarbonisation path and the potential of hydrogen as a zero-carbon alternative fuel. Using hydrogen to replace fossil fuels in various internal combustion engines shows promise in enhancing efficiency and achieving carbon-neutral outcomes. This study presents an experimental investigation of hydrogen (H2) combustion and engine performance in a boosted spark ignition (SI) engine. The H2 engine incorporates both port fuel injection (PFI) and direct injection (DI) hydrogen fuel systems, capable of injecting hydrogen at pressures of up to 4000 kPa in the DI system and 1000 kPa in the PFI operations. This setup enables a direct comparison of the performance and emissions of the PFI and DI operations. The study involves varying the relative air-to-hydrogen ratio (λ) at different speeds to explore combustion and engine limits for categorising and optimising operational regions.

Climate change mitigation is the main challenge for the automotive industry, as the government issues legislation to combat CO2 emissions. In addition to electrification and battery electric vehicles, using low-carbon and zero-carbon fuels in Internal Combustion (IC) engines can also be an effective way to reach net zero-carbon transport. This study investigated and compared the combustion characteristics, performance and emissions of a highly boosted spark ignition (SI) engine fuelled with EU VI 95 RON E10 gasoline and blends of second-generation bio-gasoline with different ethanol contents of 5% (E5), 10% (E10), and 20% (E20). The single-cylinder SI engine was equipped with a centrally mounted high-pressure injector and supplied externally boosted air. Engine experiments were conducted at 2000 RPM and 3000 RPM with low and high load operations.

Significant reductions in vehicle carbon dioxide (CO2) emissions are required to meet fleet targets and this is increasing the interest in new combustion concepts for internal combustion engines. There is also an increased focus on the use of renewable fuels to reduce environmental impact. This study focusses on the use of methanol as an internal combustion engine fuel. Methanol is a liquid fuel that is readily produced from waste bio-matter, as well as synthetically using renewable energy, and is proposed as a primary energy vector in hard-to-decarbonise sectors, such as Marine, but could be equally applicable to road transportation. In this study, the MAHLE Di3 engine, which is a highly boosted 3-cylinder gasoline direct injection engine capable of operating at over 30 bar BMEP, has been modified to include MAHLE Jet Ignition technology, in both passive and active configurations, as well as utilising a very high compression ratio to maximise thermal efficiency.

The automobile industry is under intense pressure to reduce carbon dioxide (CO2) emissions of vehicles. There is also increasing pressure to reduce the other tail-pipe emissions from vehicles to combat air pollution. Electric powertrains offer great potential for eliminating tailpipe CO2 and all other tailpipe emissions. However, current battery technology and recharging infrastructure still present limitations for some applications, where a continuous high-power demand is required. Furthermore, not all markets have the infrastructure to support a sizeable electric fleet and until the grid energy generation mix is of a sufficiently low carbon intensity, then significant vehicle life-cycle CO2 savings could not be realized by the Battery Electric Vehicles. This investigation examines the effects of combustion, efficiencies, and emissions of two alcohol fuels that could help to significantly reduce CO2 in both tailpipe and the whole life cycle.

Vehicle manufacturers are facing increasing legislative pressure to reduce vehicle emissions and achieve zero tailpipe CO2 emissions within the coming decade. The focus on techniques to reduce the tailpipe CO2 emissions, rather than vehicle lifecycle emissions, naturally dictates electrified solutions. However, this will not address the increased emissions resulting from vehicle manufacture, the emissions of the legacy fleet, or enable niche or classic applications, to be decarbonised for future use. The use of bio-derived fuels, and fully synthetic fuels, can provide a technical solution to these challenges, but it is beneficial if these can be used as a drop-in replacement to existing fossil derived fuels, as this would enable straight-forward backward compatibility with existing vehicles and avoid the need to re-engineer future engine designs or upgrade existing hardware.

Today the light-duty commercial market is dominated by internal combustion engine powered vehicles, primarily diesel-powered delivery vans, which contribute to urban air quality issues. Global concerns regarding climate change have prompted zero emission vehicles to be mandatory in many markets as soon as 2035. For the light-duty commercial vehicle sector there is significant interest in pure electric vehicles. However, for some markets, or usage cases, electric vehicles may not be the best solution due to practical limitations of battery energy storage capacity or recharging times. For such applications there is growing interest in hydrogen fuel cells as a zero emissions alternative. Bramble Energy’s patented printed circuit board (PCB) fuel cell technology (PCBFC™) enables the use of cost-effective production methods and materials from the PCB industry to reduce the cost and complexity of manufacturing hydrogen fuel cell stacks.

Mild hybridisation, using a 48 V system architecture, offers fuel consumption benefits approaching those achieved using high-voltage systems at a much lower cost. To maximise the benefits from a 48 V mild-hybrid system, it is desirable to recuperate during deceleration events at as high a power level as possible, whilst at the same time having a relatively compact and low cost system. This paper examines the particular requirements of the battery pack for such a mild-hybrid application and discusses the trade-offs between battery power capabilities and possible fuel consumption benefits. The technical challenges and solutions to design a 48 V mild-hybrid battery pack are presented with special attention to cell selection and the thermal management of the whole pack. The resulting battery has been designed to achieve a continuous-power capability of more than 10 kW and a peak-power rating of up to 20 kW.

The HyPACE (Hybrid Petrol Advanced Combustion Engine) project is a part UK government funded research project established to develop a high thermal efficiency petrol engine that is optimized for hybrid vehicle applications. The project combines the capabilities of a number of partners (Jaguar Land Rover, BorgWarner, MAHLE Powertrain, Johnson Matthey, Cambustion and Oxford University) with the target of achieving a 10% vehicle fuel consumption reduction, whilst still achieving a 90 to 100 kW/liter power rating through the novel application of a combination of new technologies. The baseline engine for the project was Jaguar Land Rover’s new Ingenium 4-cylinder petrol engine which includes an advanced continuously variable intake valve actuation mechanism. A concept study has been undertaken and detailed combustion Computational Fluid Dynamics (CFD) models have been developed to enable the optimization of the combustion system layout of the engine.

MAHLE has developed a heavily downsized demonstrator engine to explore the limits, and potential benefits, of engine downsizing. The 1.2 litre, 3-cylinder, MAHLE downsizing (Di3) engine, in conjunction with an Aeristech 48 V electric supercharger (eSupercharger, eSC), achieves a BMEP level of 35 bar and a specific power output in excess of 160 kW/litre. The eSupercharger enables high specific power output, good low speed torque and excellent transient response. The resulting heavily downsized engine has been installed into a demonstrator vehicle that also features 48 V mild hybridization. At specific power output levels above 90 kW/litre the engine is operated with excess fuel in order to protect the turbine from excessive exhaust gas temperatures. In this analytical study, the boosting system requirements to maintain lambda 1 fuelling, via the use of EGR, across the entire engine operating map for the eSupercharged version of the MAHLE Di3 engine, have been explored.

Gasoline engine downsizing is already established as a technology for reducing vehicle CO2 emissions. Further benefits are possible through more aggressive downsizing, however, the tradeoff between the CO2 reduction achieved and vehicle drivability limits the level of engine downsizing currently adopted by vehicle manufacturers. This paper will present the latest results achieved from a very heavily downsized engine, and resulting demonstrator vehicle, featuring eSupercharging in combination with a conventional turbocharger. The original 1.2 litre, 3-cylinder, MAHLE downsizing engine has been re-configured to enable a specific power output in excess of 160 kW/litre. Of key importance is a cost effective, efficient and flexible boosting system.

The complexity of modern powertrain development is demonstrated by the combination of requirements to meet future emission regulations and test procedures such as Real Driving Emissions (RDE), reduction of fuel consumption and CO2 emissions as well as customer expectations for good driving performance. Gasoline engine downsizing is already established as a proven technology to reduce automotive fleet CO2 emissions. Additionally, alternative fuels such as natural gas, offer the potential to significantly reduce both tailpipe CO2 and other regulated exhaust gas emissions without compromising driving performance and driving range. This paper presents results showing how the positive fuel properties of natural gas can be fully utilised in a heavily downsized engine. The engine has been modified to cope with the significantly higher mechanical and thermal loads when operating at high specific outputs on compressed natural gas (CNG).

Gasoline engine downsizing is already established as a proven technology to reduce automotive fleet CO2 emissions by as much as 25 %. Further benefits are possible through more aggressive downsizing, however, the trade-off between the CO2 reduction achieved and vehicle drive-ability limits the level of engine downsizing currently adopted. This paper presents results showing the benefits of adding an eSupercharger to a very heavily downsized engine. Measurements are presented from a 1.2 litre, 3-cylinder, engine fitted with an eSupercharger in addition to a conventional turbocharger. The original MAHLE downsizing engine has been re-configured to enable a specific power output that exceeds 160 kW/litre. Of key importance is a cost effective, efficient and flexible boosting system.

Extreme engine downsizing is a modern solution aimed towards the goal of meeting new emissions regulations for internal combustion engines. A higher percentage downsized engine will produce less CO2. By extension, a higher boost level is required to generate high engine torque performance. The transient load step of a higher boost system at low RPM is currently an issue for conventional boosting. Aeristech has developed an electric supercharger to be matched with a conventional turbocharger to create a new type of two stage boosting system and a simpler downsized gasoline engine usable in mainstream vehicle segments. Whereas most electric pressure charging devices are capable of transient output to alleviate turbo lag. The electric supercharger is capable of steady-state air delivery. This makes the electric supercharger a dual-function device, alleviating turbo lag and also supplementing the compressor map of the turbocharger or main boost device.

Present automobile development is keenly focused on measures to reduce the CO2 output of vehicles. Plug-in hybrid electric vehicles (PHEVs) enable grid electricity, which is clean in tail-pipe emissions terms, to be utilised whilst the on-board electrical storage has sufficient charge. MAHLE Powertrain and Protean have jointly developed a plug-in hybrid demonstrator vehicle based on a C-segment passenger car. The vehicle features Protean’s compact direct drive in-wheel motors with integrated inverters on the rear axle and retains the standard gasoline engine, and manual transmission, on the front axle. To support this one-off prototype, a flexible vehicle control unit has been developed, which is easily re-configurable and adaptable to any hybrid vehicle architecture.

In 2012 MAHLE Powertrain developed a range-extended electric vehicle (REEV) demonstrator, based on a series hybrid configuration, and uses a battery to store electrical energy from the grid. Once the battery state of charge (SOC) is depleted a gasoline engine (range extender) is activated to provide the energy required to propel the vehicle. As part of the continuing development of this vehicle, MAHLE Powertrain has developed control software which can intelligently manage the use of the battery energy through the combined use of GPS and road topographical data. Advanced knowledge of the route prior to the start of a journey enables the software to calculate the SOC throughout the journey and pre-determine the optimum operating strategy for the range extender to enable best charging efficiency and minimize NVH. The software can also operate without a pre-determined route being selected.

MAHLE Powertrain has built a range-extended electric vehicle demonstrator, with a series hybrid configuration. The vehicle is intended to operate predominantly purely electrically. Once the battery state of charge is depleted a gasoline engine (range extender) is activated to provide the energy required to propel the vehicle. As part of the continuing development of this vehicle, MAHLE Powertrain has recorded data during real world driving, with the aim of further investigating the actual usage a range-extended electric vehicle under non-laboratory test conditions. The vehicle is instrumented with a data acquisition system which records physical parameters, for example coolant temperatures, as well as CAN-based data from the engine and vehicle management systems.

MAHLE Powertrain have developed a plug-in hybrid demonstrator vehicle. To support this one-off prototype, a flexible control unit has been developed, which is easily re-configurable and adaptable to any vehicle architecture. The unit operates using software developed in-house to achieve a fully configurable vehicle control unit (VCU), intended to provide a rapid and cost effective platform for the development of demonstrator and small validation prototype vehicle fleets. The executable code is auto-generated from graphical Simulink / TargetLink models, which greatly reduces development time and risk of errors. The graphical source code also provides comprehensive documentation for users of the system. This paper describes the resulting vehicle control unit and gives details of the application of the unit within the plug-in hybrid demonstrator vehicle.

In a typical plug-in hybrid electric vehicle (PHEV) installation, there exist multiple, potentially separate, cooling circuits. These circuits may have individual cooling/heating requirements or they may have common aspects. Opportunities exist for combining circuits for series applications for cost, weight and efficiency benefits. However, careful consideration must be paid to the compatibility of these circuits both in terms of temperature range requirements, but also in terms of the thermal loading of the systems on the cooling circuits. This paper presents details of a cooling system for a PHEV demonstrator recently completed by MAHLE Powertrain. The opportunities for the integration of several cooling circuits, including the cabin heating, ventilation and air-conditioning (HVAC) system, to optimise the system from a cost, package-space and weight perspective are discussed.

This paper, which is the fourth of a series, presents the REEV demonstrator vehicle developed by MAHLE Powertrain, which features a specifically designed range extender unit. The previous papers describe the specification setting, detailed design and the development of the range extender engine. A current production gasoline fuelled compact-class car was used as a donor vehicle and converted into a range-extended electric vehicle (REEV). The all-electric driveline specification has been developed to meet the performance criteria set for the demonstrator, matching the acceleration and maximum speed capabilities of the conventional donor vehicle. Also, a target electric only range has enabled the battery pack capacity to be specified. The resulting vehicle is intended to reflect likely, near to market, steps to further the wider adoption of electric vehicles in the compact-class passenger car segment.

This paper forms the third of a series and presents results obtained during the testing and development phase of a dedicated range-extender engine designed for use in a compact-class vehicle. The first paper in this series used real-world drive logs to identify usage patterns of such vehicles and a driveline model was used to determine the power output requirements of a range-extender engine for this application. The second paper presented the results of a design study. Key attributes for the engine were identified, these being minimum package volume, low weight, low cost, and good NVH. A description of the selection process for identifying the appropriate engine technology to satisfy these attributes was given and the resulting design highlights were described. The paper concluded with a presentation of the resulting specification and design highlights of the engine. This paper will present the resulting engine performance characteristics.