Search Results

Options for CNVII emission legislation are being widely investigated in a national program organized by China Vehicle Emission Control Center (VECC) since early 2020. It is foreseen that this possibly last legislation in China will have more stringent emission requirements compared to CNVI, including among other changes especially a further reduction of nitrogen oxide (NOx), inclusion of nitrous oxide (N2O) and sub-23 nm particle number (PN). This study investigates the technical feasibility to fulfill a CNVII emission legislation scenario, based on a modified CNVI 8 L engine operating under both cold and hot World Harmonized Transient Cycle (WHTC) and Low Load Cycle (LLC).

China 6 emission legislation was finalized in 2018 and the full implementation nationwide is postponed to 2021 due to COVID-19. It is foreseen that the post China 6 legislation will have more stringent primary and secondary emission requirements including further reduction of nitrous oxide (N2O) emissions and likely to include limits on ammonia (NH3) emissions. This study investigated the secondary emissions (i.e. N2O and NH3) of a variety of China 6 production gasoline vehicles operating under the worldwide harmonized light vehicles test cycle (WLTC) and random test standardized aggressive (RTS 95) cycle. It was found that N2O emissions were less than 5 mg/km on all these vehicles, far below the current China 6 limit (20 mg/km), however NH3 emissions varied from 2 to 48 mg/km among the production vehicles. The mechanisms of N2O and NH3 formation and their correlation with primary emissions were also investigated.

In order to study the influence of lubricant ash on the performance of the CN6 after-treatment system, especially the catalyst characteristics of Coated Gasoline Particulate Filter (CGPF), the system was rapidly aged on the engine bench by blending combustion method, and the ash content of 60g represented the endurance of 200kkm CGPF. The effects of CGPF with different endurance mileage on particulate matter emission, gas light-off temperature and engine performance of a Gasoline Direct Injection (GDI) vehicle were studied on the engine bench, chassis dynamometer and real-road tests. Finally, the ash distribution was analyzed by computed tomography (CT). The results showed that the vehicle equipped with CGPF could meet the requirements of CN6 particulate and gas emission limits under both worldwide harmonized light vehicles test cycle (WLTC) and real driving emission (RDE) tests.

Due to benefits from the use of electric power, Hybrid Electric Vehicles (HEVs) and Plug-in Hybrid Electric Vehicles (PHEVs) are regarded to be superior over conventional Internal Combustion Engine (ICE) only vehicles in fuel economy and emissions. However, recent studies find out that this is not always true. On certain conditions, hybrid vehicles can be even more polluted. In order to identify these challenges and develop catalysts to meet more stringent emission requirement in the future, e.g. Euro 7, for hybrid application, as a part of our xHEV project, this study includes exclusively extensive investigation on a latest Euro 6d temp Parallel PHEV.

Conventional diesel-fuelled Partially Premixed Compression Ignition (PPCI) engines have been investigated by many researchers previously. However, the ease of ignition and difficulty of vaporization of diesel fuel make it imperfect for PPCI combustion. In this study, dieseline (blending of diesel and gasoline) was looked into as the Partially Premixed Compression Ignition fuel for its combination of two fuel properties, ignition-delay-increasing characteristics and higher volatility, which make it more suitable for PPCI combustion compared to neat diesel. A series of tests were carried out on a Euro IV light-duty common-rail diesel engine, and different engine modes, from low speed/load to middle speed/load were all tested, under which fuel blend ratios, EGR rates, injection timings and quantities were varied. The emissions, fuel consumption and combustion stability of this dieseline-fuelled PPCI combustion were all investigated.

In this paper, the microscopic spray characteristics of diesel, Rapeseed Methyl Ester (RME) and Gas-to-Liquid (GTL) fuel, were studied at different injection pressures and measuring positions using Phase Doppler Anemometry (PDA) technique and the velocity development and size distributions of the fuel droplets were analysed in order to understand spray atomisation process. The injection pressures ranged from 80MPa to 150MPa, and the measuring position varied from 20mm to 70mm downstream the nozzle. It was found that the data rate is quite low in the near nozzle region and at high injection pressure. Sauter Mean Diameter (SMD) of all fuels obviously decreases when the injection pressure increases from 80MPa to 120MPa; but the injection pressure has little promotion on the axial velocity of droplets.

Pilot injection has been used widely in diesel engines for its NOx and noise reducing characteristics. In this paper, its impacts to the particle emissions were studied using a light-duty common-rail Euro 4 diesel engine with different pilot injection strategies. Three steady-state engine modes were selected from the EU legislative diesel engine test cycle to represent low, medium and high engine speeds and loads. The quantities and injection timings of the pilot injection strategies were then varied. The particle number concentration and size distributions were investigated along with the smoke and regulated gas emissions such as the NOx trade-off. These results indicate how a pilot injection alongside a main injection can increase the particle size compared to a single main injection event. Furthermore, the split injection was closely related to the engine mode.

In this study, the application of two closely coupled Diesel Particle Filters (DPFs), composed of an assistant DPF and a main standard honeycomb DPF, was investigated. A series of tests were carried out on a light-duty common-rail Euro 4 diesel engine and the emissions were measured and compared with those when a standard DOC+DPF system was used for the after-treatment. Replacing the DOC with an assisting DPF (ADPF) showed significant advantages in the reduction of particles, which had a direct impact in reducing the soot loading rate of the main DPF by up to 30%. Its oxidation characteristics not only showed equivalent exhaust-conversion efficiency, which concern the regulated gaseous emissions (CO and HC) under most engine conditions, but also continuously regenerated the soot it trapped.

In this study, the particle emission characteristics of 10% alternative diesel fuel blends (Rapeseed Methyl Ester and Gas-to-Liquid) were investigated through the tests carried out on a light duty common-rail Euro 4 diesel engine. Under steady engine conditions, the study focused on particle number concentration and size distribution, to comply with the particle metrics of the European Emission Regulations (Regulation NO 715/2007, amended by 692/2008 and 595/2009). The non-volatile particle characteristics during the engine warming up were also investigated. They indicated that without any modification to the engine, adding selected alternative fuels, even at a low percentage, can result in a noticeable reduction of the total particle numbers; however, the number of nucleation mode particles can increase in certain cases.