Search Results

Insertion loss in one-third or octave bands is widely used in industry to assess the performance of large silencers and mufflers. However, there is no standard procedure for determining the transmission loss in one-third or octave bands using measured data or simulation. In this paper, assuming that the source is broadband, three different approaches to convert the narrowband transmission loss data into one-third and octave bands are investigated. Each method is described in detail. To validate the three different approaches, narrowband transmission loss data of a simple expansion chamber and a large bar silencer is converted into one-third and octave bands, and results obtained from the three approaches are demonstrated to agree well with one another.

Prior research on assessing multiple inlet and outlet mufflers is limited, and only recently have researchers begun to consider suitable metrics for multiple inlet and outlet mufflers. In this paper, transmission loss and insertion loss are defined for multiple inlet and outlet mufflers using a superposition method that can be extended to any m-inlet n-outlet muffler. Transmission loss is determined assuming that the sources and terminations are anechoic. On the other hand, insertion loss considers reflections. For both metrics, the amplitude and phase relationship between the sources should be known a priori. This paper explains both metrics, and measurement of transmission and insertion loss are demonstrated for a 2-inlet 2-outlet muffler with good agreement.

A recently developed superposition approach for determining the insertion loss of a two-inlet muffler is reviewed. To validate the approach, calculated and measured insertion losses are compared for a small engine muffler with two inlets and one outlet. After which, the phasing between the two inputs is varied and the insertion loss is evaluated. Results show that the insertion loss is strongly affected by the phasing between sources at low frequencies while phasing between sources has a lesser impact at high frequencies. At the conclusion of the paper, the theory for applying the superposition approach to transmission loss is reviewed.

In many industries, muffler and silencer design is primarily accomplished via trial and error. Prototypes are developed and tested, or numerical simulation (finite or boundary element analysis) is used to assess the performance. While these approaches reliably determine the transmission loss, designers often do not understand why their changes improve or degrade the muffler performance. Analyses are time consuming and models cannot be changed without some effort. The intent of the current work is to demonstrate how plane wave muffler models can be used in industry. It is first demonstrated that plane wave models can reliably determine the transmission loss for complicated mufflers below the cutoff frequency. Some tips for developing dependable plane wave models are summarized. Moreover, it is shown that plane wave models used correctly help designers develop intuition and a better understanding of the effect of their design changes.

Micro-perforated (MPP) panels are acoustic absorbers that are non-combustible, acoustically tunable, lightweight, and environmentally friendly. In most cases, they are spaced from a wall, and that spacing determines the frequency range where the absorber performs well. The absorption is maximized when the particle velocity in the perforations is high. Accordingly, the absorber performs best when positioned approximately a quarter acoustic wavelength from the wall, and larger cavity depths improve the low frequency absorption. At multiples of one half acoustic wavelength, the absorption is minimal. Additionally, the absorption is minimal at low frequencies due to the limited cavity depth behind the MPP. By partitioning the backing cavity, the cavity depth can be strategically increased and varied. This will improve the absorption at low frequencies and can provide absorption over a wide frequency range.

The measurement of sound absorption coefficient (SAC) of porous materials is covered by both American and international standards. However, by using the standards alone it is difficult to achieve consistently repeatable results given the large number of variables such as sample cutting and preparation, sample fit and position in the tube, and sample material variability. This paper will review the standards briefly and examine what is available in the literature to guide users in making consistently repeatable SAC measurements. The paper will also show some of the authors' results and interpret these results in light of the standards and technical literature on the subject.

The two-load method is commonly used to determine the transmission loss of a muffler or silencer. Several practical measurement considerations are examined in this paper. First of all, conical adapters are sometimes used to transition between impedance tubes and the muffler. It is demonstrated that the effect of adding the adapter can be quite significant at low frequencies especially if the adapter is short in length. The effect of changing the length of the adapter was examined via measurement and plane wave theory. Secondly, the effect of selecting the reference microphone was examined experimentally. It was found that measurements are improved by selecting a downstream reference. Finally, the effect of using different frequency response function estimation algorithms (H1, H2 and Hv) was compared sans flow. This had little effect on the measurement.

This paper documents a finite element approach to predict the attenuation of muffler and silencer systems that incorporate diesel particulate filters (DPF). Two finite element models were developed. The first is a micro FEM model, where a subset of channels is modeled and transmission matrices are determined in a manner consistent with prior published work by Allam and Åbom. Flow effects are considered at the inlet and outlet to the DPF as well as viscous effects in the channels themselves. The results are then used in a macro FEM model of the exhaust system where the transmission relationship from the micro-model is used to simulate the DPF. The modeling approach was validated experimentally on an example in which the plane wave cutoff frequency was exceeded in the chambers upstream and downstream to the DPF.