Search Results

Partially Premixed Combustion (PPC) has demonstrated substantially higher efficiency compared to conventional diesel combustion (CDC) and gasoline engines (SI). By combining experiments and modeling the presented work investigates the underlying reasons for the improved efficiency, and quantifies the loss terms. The results indicate that it is possible to operate a HD-PPC engine with a production two-stage boost system over the European Stationary Cycle while likely meeting Euro VI and US10 emissions with a peak brake efficiency above 48%. A majority of the ESC can be operated with brake efficiency above 44%. The loss analysis reveals that low in-cylinder heat transfer losses are the most important reason for the high efficiencies of PPC. In-cylinder heat losses are basically halved in PPC compared to CDC, as a consequence of substantially reduced combustion temperature gradients, especially close to the combustion chamber walls.

The acoustic and performance characteristics of an automotive centrifugal compressor are studied on a steady-flow turbocharger test bench, with the goal of advancing the current understanding of compression system instabilities at the low-flow range. Two different ducting configurations were utilized downstream of the compressor, one with a well-defined plenum (large volume) and the other with minimized (small) volume of compressed air. The present study measured time-resolved oscillations of in-duct and external pressure, along with rotational speed. An orifice flow meter was incorporated to obtain time-averaged mass flow rate. In addition, fast-response thermocouples captured temperature fluctuations in the compressor inlet and exit ducts along with a location near the inducer tips.

The paper presents a thermal management development capability and approach that was put in place to understand the relative benefit of various thermal components, layouts and control strategies. The use of the approach on a modern diesel powered vehicle is given. Thermal performance along with associated fuel economy improvements are shown over various test cycles including the FTP and US06. Results are given for a GT-Suite simulation as well as on vehicle.

Using a 3 liter, 4 valves per cylinder, V6 Diesel engine model, this study investigates late intake valve closing (LIVC) time in an effort to reduce the fuel consumption of the engine. Two different intake cam duration technologies for diesel engines are evaluated using a 1-D engine simulation software code. The first method utilized for duration control delays the effective closing of the intake valve by moving one intake cam lobe with respect to the other baseline intake cam lobe. In the second method, the closing of both intake valves is delayed by the introduction of an adjustable dwell period during the closing portion of the valve motion. During this mid-lift dwell period, the lift is held at a constant value until it goes into the closing phase. The systems are evaluated and compared at 4 operating points of varying engine speed and load. At each operating point, while engine load is held constant, intake valve closing time is varied.

In our introductory paper on the VEMB system (SAE 2010-01-1222) we discussed the concept of a divided exhaust period turbocharging system controlled by a concentric cam system, and we presented several fixed speed/load point sets of results that demonstrated the expected BSFC benefits. The BSFC reductions (2.5% to 4%) correlated to reduction in pumping work and to improvement in combustion phasing at knock-limited points from substantial reductions in Residual Gas Fraction compared to the conventionally-boosted baseline engine. In this paper we present additional results from engine tests in the areas of full-load performance and emissions with and without Scavenge-sourced EGR. To demonstrate the WOT performance potential of a VEMB engine, we show the effect of turbocharger matching steps, with results that exceed the baseline engine output across the engine speed range.

Trying to improve the modern diesel engine's NOx/soot tradeoff without giving up fuel economy continues to be a core target for the engine development community. One of the options not yet fully investigated for the diesel is applying variable valve events to the engine breathing process. Already used in some heavy-duty applications, late intake valve closing has long been regarded as a possible strategy for small diesel engines. Single-cylinder tests applying fully variable valve events have demonstrated potential but also raised doubts about VVA benefits on automotive size diesel engines. Full engine testing using realistic valve train technology is seen as key to judging its true performance because it covers not only combustion benefits but also influences like engine pumping on emissions and CO₂. Different to past publications, this paper focuses on testing a production feasible variable valve train technology on a fully instrumented modern Common Rail diesel engine.

The paper presents the structure of an air system controller and its application to a modern boosted dual loop EGR Diesel engine. Results over a U.S. FTP cycle which show improvements in emissions and fuel consumption with future opportunities for increased performance are discussed. A recent application of the controller is also shown where standard engine sensors are eliminated to reduce cost and their function is replaced with in-cylinder pressure measurement combined with signal processing techniques.

The unsteady surge behavior of a turbocharger compression system is studied computationally by employing a one-dimensional engine simulation code. The system modeled represents a new turbocharger test stand consisting of a compressor inlet duct breathing from ambient, a centrifugal compressor, an exit duct connected to an adjustable-volume plenum, followed by another duct which incorporates a control valve and an orifice flow meter before exhausting to ambient. Characteristics of mild and deep surge are captured as the mass flow rate is reduced below the stability limit, including discrete sound peaks at low frequencies along with their amplitudes in the compressor (downstream) duct and plenum. The predictions are then compared with the experimental results obtained from the cold stand placed in a hemi-anechoic room.

The behavior of the compression system in turbochargers is studied with a one-dimensional engine simulation code. The system consists of an upstream compressor duct open to ambient, a centrifugal compressor, a downstream compressor duct, a plenum, and a throttle valve exhausting to ambient. The compression system is designed such that surge is the low mass flow rate instability mode, as opposed to stall. The compressor performance is represented through an extrapolated steady-state map. Instead of incorporating a turbine into the model, a drive torque is applied to the turbocharger shaft for simplification. Unsteady compression system mild surge physics is then examined computationally by reducing the throttle valve diameter from a stable operating point. Such an increasing resistance decreases the mass flow rate through the compression system and promotes surge.

Naturally aspirated HCCI operation is typically limited to medium load operation (∼ 5 bar net IMEP) by excessive pressure rise rate. Boosting can provide the means to extend the HCCI range to higher loads. Recently, it has been shown that HCCI can achieve loads of up to 16.3 bar of gross IMEP by boosting the intake pressure to more than 3 bar, using externally driven compressors. However, investigating HCCI performance over the entire speed-load range with real turbocharger systems still remains an open topic for research. A 1 - D simulation of a 4 - cylinder 2.0 liter engine model operated in HCCI mode was used to match it with off-the-shelf turbocharger systems. The engine and turbocharger system was simulated to identify maximum load limits over a range of engine speeds. Low exhaust enthalpy due to the low temperatures that are characteristic of HCCI combustion caused increased back-pressure and high pumping losses and demanded the use of a small and more efficient turbocharger.

The thermal management of vehicles has increased in importance due to the significant role of friction and auxiliary losses in engine operation on CO2 emissions. To evaluate different system and component concepts regarding their influence on fuel consumption, simulation offers a wide range of opportunities. In this paper a fully integrated model is presented utilizing the GT-Suite commercial code. It contains a diesel engine system model, a cooling circuit including a simplified model for the cooler package in the vehicle front end and a vehicle model. The purpose of this model is the investigation of cooling system components and control strategies with different engine inputs. A significant run time advantage is achieved by using a mean value engine model, which has a reduced number of input parameters. The simulation using the integrated model can be carried out within an acceptable time frame which enables vehicle drive cycle analysis.

It has been clearly demonstrated separately, that the application of both Dual Cam Phasers (DCP) and External Cooled EGR systems are highly beneficial to improving the efficiency of highly-boosted GDI engines. DCP systems can optimize the volumetric efficiency at WOT conditions, improve boost and transient response at low engine speeds, and provide internal EGR at low RPM part-load conditions. External cooled EGR has been demonstrated to dramatically improve the fuel consumption, lower turbine inlet temperature, and improve emissions at high power conditions. In previous investigations by the BorgWarner Engine Systems Group, we showed that full engine speed/load range EGR coverage can be obtained by combining High Pressure Loop and Low Pressure Loop external EGR systems with a DCP strategy.