Search Results

Polyurethane foam (PU foam) is widely used in automotive noise reduction palliatives. As a decoupling insulator its acoustic performance depends on intrinsic properties, called “Biot” parameters. An important decoupling parameter is the apparent stiffness of the PU foam cell structure, as this controls the transportation of vibrational energy, with “softer PU foam” being the preferred option. However, some areas of application, for example in automotive carpet design, requires stiffer PU foam in order to accommodate under foot comfort. For a comprehensive approach to automotive component design, it is necessary to calculate the appropriate spatial PU foam properties ideally without the need for series of prototypes. This paper describes the methods and processes used when compiling and validating a material database capable of predicting the acoustic performance of flat sample or spatially complex 3D component with minimal prototype manufacture.

Automotive suppliers provide multi-layer trims mainly made of porous materials. They have a real expertise on the characterization and the modeling of poro-elastic materials. A dozen parameters are used to characterize the acoustical and elastical behavior of such materials. The recent vibro-acoustic simulation tools enable to take into account this type of material but require the Biot parameters as input. Several characterization methods exist and the question of reproducibility and confidence in the parameters arises. A Round Robin test was conducted on three poro-elastic material with four laboratories. Compared to other Round Robin test on the characterization of acoustical and elastical parameters of porous material, this one is more specific since the four laboratories are familiar with automotive applications. Methods and results are compared and discussed in this work.

The noise treatments weight reduction strategy, which consists in combining broadband absorption and insulation acoustic properties in order to reduce the weight of barriers, depends strongly on surface to volume ratio of the absorbing layers in the reception cavity. Indeed, lightweight technologies like the now classical Absorber /Barrier /Absorber layup are extremely efficient behind the Instrument Panel of a vehicle, but most of the time disappointing when applied as floor insulator behind the carpet. This work aims at showing that a minimum of 20 mm equivalent “shoddy” standard cotton felt absorption is requested for a floor carpet insulator, in order to be able to reduce the weight of barriers. This means that a pure absorbing system that would destroy completely the insulation properties and slopes can only work, if the noise sources are extremely low in this specific area, which is seldom the case even at the rear footwells location.

The Flaxpreg is a green and light very long flax fibers thermoset reinforced sandwich, which can be effectively used as multi-position trunk loadfloor or structural floor in the passenger compartment of a vehicle. The prepreg FlaxTapes of about 120 g/m2 constituting the skins of the sandwich, are unidirectionally aligned flax fibers tapes, with acrylic resin here, easily manipulable without requiring any spinning or weaving step and thus without any negative out of plane crimping of the almost continuous flax fibers. Thanks to their very low 1.45 kg/dm3 density combined with an adaptive 0°/90°/0° orientation of the FlaxTapes (for each skin) depending on the loading boundary conditions, the resulting excellent mechanical properties allow a - 35% weight reduction compared to petro-sourced Glass mat/PUR sandwich solutions (like the Baypreg).

Strategies for weight reduction have driven the noise treatment advanced developments with a great success considering the already mastered weight decreases observed in the last years in the automotive industry. This is typically the case for all soft trims parts. In the early 2010's a typical european B-segment car soft trims weights indeed 30 to 40% less than in the early 2000's years. The main driver behind such a gap has been to combine insulation and absorption properties on a single part while increasing the number of layers. This product-process evolution was conducted using a significant improvement in the simulation capacities. In that sense, several studies presenting very good correlation results between Transmission Loss measurements and finite elements simulations on dashboard or floor insulators were presented. One may consider that those kinds of parts have already achieved a considerable improvement in performance.

In order to reach the new 2020 CO2 emissions regulations, we have developed a wide range of lightweight noise treatment technologies going from pure absorbing to highly insulating ones, depending on the pass-through quality situation. This Generalized Light-Weight Concepts family was first optimized using the 2D Transfer Matrix Method (TMM) combined with quick SEA approaches. Taking into account thickness 3D maps with TMM is an efficient and quick intermediate “2,5D” optimization method, but it is not a real 3D approach. This work presents a new 3D optimization procedure based on poroelastic finite elements including intermediate cavities (like Instrument Panels) for designing these Generalized Light-Weight Concepts. A parallel reflection deals with products and processes in order to check the feasibility of the resulting 3D optimized insulator designs.

Due to increasing attention paid to the optimization of leakages and passthroughs in general, measurements on cut out modules in large coupled reverberant rooms are often carried out in the middle and high frequency range, in order to optimize the insulation performance of trims installed in their actual environment (Transmission Loss). Using optimal controlled mounting conditions, we have been able to extend the frequency range to the low frequencies in order to validate trim FEM models of a headliner cut out module with structureborne and airborne excitations.

The weight reduction challenge has taken a new shape in the past two years due to high pressure on CO2 emissions in the automotive industry. The new question is: what level of acoustic performance can you get with an insulator weighting less than 2500 g/m2? The existing solutions at this weight being mainly dissipative (absorption) concepts give a satisfactory performance only if the pass-throughs are poor and present critical leakages. Respecting the less than 2500 g/m2 weight target, we have developed a wide range of new or optimized concepts switching from extremely absorbing to highly insulating noise treatments playing with multi-layers insulators (typically three to four layers), in combination or not with tunable absorbers on the other side of the metal sheet (in the engine compartment for example).