Search Results

Stringent emission regulations on one hand and increasing demand for better fuel economy along with lower noise levels on the other hand require adoption of advanced common-rail direct-injection technologies in diesel engines. In the present work, a small 0.9-l, naturally aspirated, two-cylinder, common-rail direct-injection diesel engine is used for the analysis of combustion noise at different engine operating conditions. Experiments are conducted at different loads and engine speeds, incorporating both single and multiple (i.e. pilot and main) injections along with different injection timings. In the case of multiple injections, the influence of pilot injection quantity is also evaluated on the combustion noise while maintaining the same load. In-cylinder pressure was recorded with the resolution of 0.1 crank angle degree, and it was used for the quantitative analysis of noise assessed from the resulting cylinder pressure spectra, and sound pressure level.

For long time, the measurement of spatially and temporally varying quantities like in-cylinder flow, mixing, and burning in an internal combustion engine remained impossible due to the lack of access to the engine cylinder. Hence, for quite some time, in-cylinder pressure remained the only quantity that could be temporally measured during an engine cycle, and the variations of quantities like temperature, heat release deduced from it. However, to guide modern engine developments for improved fuel economy and reduced emissions, understanding the intricacies of in-cylinder processes are essential. The advent of optical engine in conjunction with laser-based diagnostic techniques enabled measurement of various in-cylinder processes and study their influences on the combustion process. This paper highlights some key design features of optically accessible engines for flow and combustion studies.

The replacement of fossil diesel with neat biodiesel in a compression ignition engine has advantage in lowering unburned hydrocarbon, carbon monoxide and smoke emissions. However, the injection advance experienced with biodiesel fuel with respect to diesel injection setting increases oxides of nitrogen emission. In this study, the biodiesel-NO control is attempted using charge and fuel modification strategies with retarded injection timing. The experiments are performed at maximum torque speed and higher loads viz. from 60% up to full load conditions maintaining same power between diesel and biodiesel while retarding the timing of injection by 3 deg. crank angle. The charge and fuel modifications are done by recycling 5% by volume of exhaust gas to the fresh charge and 10% by volume of methanol to Karanja biodiesel.

Owing to a high power-to-weight ratio, mini internal combustion engine is used in propelling an unmanned air vehicle. In comparison to the performance characteristics, the investigations on the combustion aspects of mini engines are scanty. This investigation concerns study of the combustion process of a mini engine and its variability. For this purpose, the experimental cylinder pressure histories were obtained on a laboratory set-up of a 7.45 cm3 capacity mini engine. The analyses of experimental data at different throttle settings reveal that there existed a varied range of rich and lean misfiring limits around a reference equivalence ratio that corresponds to the respective maximum indicated mean effective pressure. At the limiting equivalence ratios, cylinder pressure measurements showed a high degree of cycle-to-cycle variations. In some cases, a slow combustion or misfiring event preceded a rapid combustion.

From the energy security and environment standpoint, the biodiesel fuels derived from vegetable oils or animal fats appear to be promising alternative to fossil diesel. Although the engine experiments prove their viability, the scientific data base for characterizing biodiesel combustion is limited. Detailed studies on the characterization of biodiesel fuels and their effects on fundamental engine processes like droplet evaporation and combustion are essential. The present study evaluates the useful thermo-physical properties and droplet evaporation characteristics of biodiesel fuels. The droplet evaporation measurements are carried out using suspended droplet experiments on five biodiesel fuels of Indian origin viz. jatropha, pongamia (karanja), neem, mahua and palm. The droplet evaporation rates of these fuels are related to properties such as binary diffusivity and molecular weight, which in turn depend on their fatty acid composition.

Biodiesel is an emerging alternative to fossil diesel for use in compression ignition engines. From environmental standpoint, an increase in nitric oxide (NO) emission from biodiesel fueled engine has been a major concern. Several investigations suggest the role of unsaturated methyl ester as a contributor to biodiesel-NO penalty. The chemical simplicity of biodiesel compared to fossil diesel makes their composition effects amenable to a systematic analysis. In this study, the effects of saturated palm and unsaturated karanja (Pongamia pinnata) biodiesels and their blends (Bio-mix) on compression ignition engine performance, combustion and NO emission are investigated. The combustion and emission characteristics of these fuels are compared with fossil diesel that the neat biodiesel fuels result in improved exhaust emissions except NO with a penalty in fuel economy.

The classical trade-off between NOx and soot emissions from conventional diesel engines has been a limiting factor in meeting ever stringent emission norms. The electronic control of fuel injection in diesel engines emerged as an important strategy for their simultaneous reduction. The high pressure multiple-injection in a common rail direct injection system has been promising in this regard. While, the effects of pilot injection or multiple pulses of CRDI injection schedule on simultaneous reduction of NOx and soot have been widely investigated and reported, the investigations concerning three and more injection pulses have been limited. In this paper, the ability of a predictive model, developed by the authors, in providing optimal multiple-injection schedule is demonstrated through parametric investigations. The effects of pilot and post fuel quantity and dwell between the injection pulses on NOx and soot emissions are discussed.