Search Results

In order for premixed methane diesel dual fuel engines to meet current and future legislation, the emissions of unburned hydrocarbons must be reduced while high efficiency and high methane utilization is maintained. This paper presents an experimental investigation into the effects of in cylinder air motion, swirl and tumble, on the emissions, heat transfer and combustion characteristics of dual fuel combustion at different air excess ratios. Measurements have been carried out on a single cylinder engine equipped with a fully variable valve train, Lotus AVT. By applying different valve lift profiles for the intake valves, the swirl was varied between 0.5 and 6.5 at BDC and the tumble between 0.5 and 4 at BDC. A commercial 1D engine simulation tool was used to calculate swirl number and tumble for the different valve profiles. Input data for the simulation software was generated using a steady-state flow rig with honeycomb torque measurements.

In-cylinder flow pattern has been examined experimentally in a heavy duty optical diesel engine and simulated with CFD code during the combustion and the post-oxidation phase. Mean swirling velocity field and its evolution were extracted from optical tests with combustion image velocimetry (CIV). It is known that the post-oxidation period has great impact on the soot emissions. Lately it has been shown in swirling combustion systems with high injection pressures, that the remaining swirling vortex in the post-oxidation phase deviates strongly from solid body rotation. Solid body rotation can only be assumed to be the case before fuel injection. In the studied cases the tangential velocity is higher in the centre of the piston bowl compared to the outer region of the bowl. The used CIV method is closely related to the PIV technique, but makes it possible to extract flow pattern during combustion at full load in an optical diesel engine.

In-cylinder flow pattern was evaluated during diesel combustion and post-oxidation in a heavy duty optical engine and compared with CFD calculations. In this work the recently developed optical method combustion image velocimetry (CIV) is evaluated. It was used for extracting the flow pattern during combustion and post-oxidation by tracing the glowing soot clouds in the cylinder. The results were compared with CFD sector simulation on the same heavy duty engine geometry. Load was 10 bar IMEP and injection pressure was varied in two steps together with two different swirl levels. The same variations were done in both the optical engine and in the CFD simulations. The main results in this work show that the CIV method and the CFD results catch the same flow pattern trends during combustion and post-oxidation. Evaluation of the CIV technique has been done on large scale swirl vortices and compared with the CFD results at different distances from the piston bowl surface.

After-oxidation in Heavy Duty (HD) diesel combustion is of paramount importance for emissions out from the engine. During diffusion diesel combustion, lots of particulate matter (PM) is created. Most of the PM are combusted during the after-oxidation part of the combustion. Still some of the PM is not, especially during an engine transient at low lambda. To enhance the PM oxidation in the late engine cycle, swirl together with high injection pressure can be implemented to increase in-cylinder turbulence at different stages in the cycle. Historically swirl is known to reduce soot particulates. It has also been shown, that with today's high injection pressures, can be combined with swirl to reduce PM at an, for example, engine transient. The mechanism why the PM engine out is reduced also at high injection pressures is however not so well understood.

Spray and mixture formation in a compression-ignition engine is of paramount importance in the diesel combustion process. In an engine transient, when the load increases rapidly, the combustion system needs to handle low λ operation without producing high NOx emissions and large amounts of particulate matter. By changing the in-cylinder flow, the emissions and engine efficiency are affected. Optical engine studies were therefore performed on a heavy-duty engine geometry at different fuel injection pressures and inlet airflow characteristics. By applying different inlet port designs and valve seat masking, swirl and tumble were varied. In the engine tests, swirl number was varied from 2.3 to 6.3 and the injection pressure from 500 to 2500 bar. To measure the in-cylinder flow around TDC, particle image velocimetry software was used to evaluate combustion pictures. The pictures were taken in an optical engine using a digital high-speed camera.

Spray and mixture formation in a compression ignition engine is of paramount importance for diesel combustion. In engine transient operation, when the load increases rapidly, the combustion system needs to handle low lambda (λ) operation while avoiding high particle emissions. Single-cylinder tests were performed to evaluate the effect of differences in cylinder flow on combustion and emissions at typical low λ transient operation. The tests were performed on a heavy-duty single-cylinder test engine with Lotus Active Valve Train (AVT) controlling the inlet airflow. The required swirl number (SN) and tumble were controlled by applying different inlet valve profiles and opening either both inlet valves or only one or the other. The operating point of interest was extracted from engine transient conditions before the boost pressure was increased and investigated further at steady state conditions.