Search Results

Engine Mapping is usually performed under nominal conditions which include a humidity level of 8 g/Kg. Customers driving at different humidity conditions (which may range from 1 g/Kg in dry and colder climates and up to 35 g/Kg as in tropical climates) may experience a degraded performance due to the errors in engine torque estimation provided by the ECU. The torque estimation error interacts with many other features that affect drivability, such as the peak performance of the engine, transmission shift quality, etc. This paper extends the investigation in Part-1 by analyzing and quantifying the torque estimation error that may result in certain customer use cases at high humidity conditions, due to the mismatch between calibrated and actual conditions. The analysis is mainly performed for Speed-Density systems (MAP sensor based) but the effect of mass air flow sensor (MAF sensor) based systems is also briefly considered.

Traditional EGR measurement systems using delta pressure over a fixed orifice such as a DPFE sensor (Delta Pressure Feedback for EGR), have limitations in the ability to measure EGR accurately. Also, the pressure drop that results from the orifice may not be acceptable in some applications. To measure the EGR accurately and without any pressure loss, a new measurement system was developed that uses an oxygen sensor in the intake air. In this paper, the technology of using an oxygen sensor to measure the EGR concentration is discussed. The paper details the EGR measurement principle with an oxygen sensor and the associated mathematical relations of translating the oxygen measurement to EGR measurement. Factors affecting the EGR measurement such as the air/fuel ratio of the EGR, intake air pressure, and diffusion effects of the EGR constituents are discussed in detail. Compensation mechanisms are explained and associated results shown.

Engine Mapping is usually performed under nominal conditions which include a humidity level of 8 g/Kg. Customers driving at different conditions (which may range from 1 g/Kg in colder and dry climates and up to 35 g/Kg as in tropical climates) may experience less-than-optimal engine combustion which results in reduced onroad fuel economy. Humidity has an EGR-equivalent effect, and measuring it will correct the spark timing, mainly at Maximum Brake Torque (MBT) and borderline conditions, and claim back some of those losses. This paper aims at quantifying the small fuel economy benefits associated with on-board humidity measurement for certain customer use cases at high humidity conditions. Dyno data was collected for a Ford 2.3L GTDI engine at three speed load points, and intake air humidity was varied between 20% and 80% relative humidity. The effect of humidity compensation on spark timing, combustion phasing, knock, and consequently on overall engine efficiency was analyzed.

Numerous studies describe the fuel consumption benefits of changing the powertrain temperature based on vehicle operating conditions. Actuators such as electric water pumps and active thermostats now provide more flexibility to change powertrain operating temperature than traditional mechanical-only systems did. Various control strategies have been proposed for powertrain temperature set-point regulation. A characteristic of powertrain thermal management systems is that the operating conditions (speed, load etc) change continuously to meet the driver demand and in most cases, the optimal conditions lie on the edge of the constraint envelope. Control strategies for set-point regulation which rely purely on feedback for disturbance rejection, without knowledge of future disturbances, might not provide the full fuel consumption benefits due to the slow thermal inertia of the system.

Ford Motor Company is introducing “EcoBoost” gasoline turbocharged direct injection (GTDI) engine technology in the 2010 Lincoln MKS. A logical enhancement of EcoBoost technology is the use of E85 for knock mitigation. The subject of this paper is the optimal use of E85 by using two fuel systems in the same EcoBoost engine: port fuel injection (PFI) of gasoline and direct injection (DI) of E85. Gasoline PFI is used for starting and light-medium load operation, while E85 DI is used only as required during high load operation to avoid knock. Direct injection of E85 (a commercially available blend of ∼85% ethanol and ∼15% gasoline) is extremely effective in suppressing knock, due to ethanol's high inherent octane and its high heat of vaporization, which results in substantial cooling of the charge. As a result, the compression ratio (CR) can be increased and higher boost levels can be used.