Search Results

The emissions limits of CO2 for vehicles are becoming more stringent with the aim of reducing greenhouse gas emissions and improve fuel economy. The New European Driving Cycle (NEDC) is adopted to measure emissions for all new internal combustion engines in the European Union, and it is performed on cold vehicle, starting at a temperature of 22°C ± 2°C. Consequently, the cold-start efficiency of internal combustion engine is becoming of predominant interest. Since at cold start the lubricant oil viscosity is higher than at the target operating temperature, the consequently higher energy losses due to increased frictions can substantially affect the emission cycle results in terms of fuel consumption and CO2 emissions. A suitable thermal management system, such as an exhaust-to-oil heat exchanger, could help to raise the oil temperature more quickly.

International regulations are challenging automotive industry to develop more efficient systems for reducing diesel engines NOx emissions. Selective Catalytic Reduction systems may be a concrete solution, in fact SCR systems are already on the market, firstly developed for heavy duty diesel engine applications, and now it is beginning the spreading to light automotive applications. The urea-water solution dosing module may be subjected to strong heat transfer, so an efficient heat dissipation is crucial step to avoid injector's severe damages, as deformations of internal components or solenoid's fault. To have a system less complex and consequently less expensive, the dosing module air cooling should be preferred to liquid cooling. Obtain an efficient heat dissipation from the injector holder unit can represent a hard task: consequently dosing module design must be careful.

In this paper, the dependency on fuel blends of a four stroke, four cylinder SI engine equipped with a low pressure common rail type injection system is analyzed. With reference to an operating condition using E21 (21% ethanol, 79% gasoline) as a fuel, the experimental performance of the engine are firstly introduced, and the brake power, the specific fuel consumption, the total efficiency, the heating combustion power and the injected mass per stroke dependency on shaft speed are introduced. Then, the multi-fuel injection system actual behavior is predicted by means of a properly tailored lumped and distributed numerical model, whose general reliability is defined mainly in terms of injected mass per stroke. Afterward, the engine performance variation with the fuel mixture is determined, and the adaptation of the PWM control applied to injectors is proposed to compensate the engine operating characteristics.

The paper investigates the variation of the mass of the fuel injected with respect to nominal conditions in Common Rail injection systems for Diesel automotive applications. Two possible operating conditions have been considered: the consecutive injection of two injectors and the multiple shots of the same injector in the same engine cycle. An integrated experimental and numerical methodology has been used. Several experimental information were available in terms of instantaneous rail and pipe pressure and mass flow rate at different conditions. The 1D numerical model of the whole injection system was useful in addressing the questions remained unresolved in the post-experiments analysis. The experimental results show that injector performances are more related to pressure oscillations in injector connecting pipe rather than inside the common rail.

Upcoming Euro 4 and Euro 5 emission standards are increasing efforts on injection system developments in order to improve mixture quality and combustion efficiency. The target features of advanced injection systems are related to their capability of operating multiple injection with a precise control of the amount of injected fuel, low cycle-by-cycle variability and life drift, within flexible strategies. In order to accomplish this task, injector performance must be optimised by acting on: optimisation of electronic, driving circuit, detailed investigation of different nozzle hole diameter configurations, assessment of the influence of manufacturing errors on hole diameter and inlet rounding on injector performance. The paper will focus on the use of an integrated lump-1D/3D methodology for the design of advanced new fast solenoid Common Rail (C.R.) injector for high speed diesel engines. A lump-model built up in AMESim® environment was used to address the injector design.

The aim of this work is to set up a methodology for simulating Common Rail high-pressure injectors based on coupling a lump-model with CFD two-phase multi-dimensional computations. The unit simulated is the Bosch injector. The injector lump-model resulted in the definition of the three sub-models for hydraulics, mechanics and electro-magnetics. The second-order differential governing equations have been solved in Matlab/Simulink environment and are properly coupled together with the one-dimensional partial differential equations that describe the unsteady pipe flow. A detailed library of thermo-mechanical properties for ISO-4113 oil and diesel fuel is included. Cavitation effects on discharge coefficient in the main orifices were accounted for by using results from CFD steady two-phase flow simulations. The evaluation of the model capability was assessed by using detailed experiments carried out at different practical injector operating conditions.