Search Results

There is a well-recognised need for robust simulation tools to support the design and evaluation of future More-Electric Engine and Aircraft (MEE/MEA) design concepts. Design options for these systems are increasingly complex, and normally include multiple power electronics converter topologies and machine drive units. In order to identify the most promising set of system configurations, a large number of technology variants need to be rapidly evaluated. This paper will describe a method of MEE/MEA system design with the use of a newly developed transient modeling, simulation and testing tool aimed at accelerating the identification process of optimal components, testing novel technologies and finding key solutions at an early development stage. The developed tool is a Matlab/Simulink library consisting of functional sub-system units, which can be rapidly integrated to build complex system architecture models.

The aviation industry has witnessed a technological shift towards the More Electric Aircraft (MEA) concept. This shift has been driven by a number of perceived benefits including performance optimization and reduced life-cycle costs. Increased electrification within MEA has made aircraft electrical networks larger and more complex and this necessitates an increased electrical power offtake from the engine. The paralleling of multiple generation sources across the aircraft is one potential design approach which could help improve engine operability and fuel efficiency within more-electric aircraft platforms. Accordingly, this paper will investigate options for the realization of paralleled generation systems within the context of current design and certification rules. The paper first illustrates, through simulation, that MIL-STD-704F voltage envelopes may be breached for some interconnected electrical architectures under fault conditions.

The increasing electrical demand in commercial and military aircraft justifies a growing need for higher voltage DC primary distribution systems. A DC system offers reduced power losses and space savings, which is of major importance for aircraft manufacturers. At present, challenges associated with DC systems include reliable fast acting short circuit protection. Solid State Contactors (SSC) have gained wide acceptance in traditional 28 VDC secondary systems for DC fault interruption. However, the reliable operation at higher operating voltages and currents requires further technology maturation. This paper examines a supporting method to SSC for more reliable fault mitigation by investigating bidirectional AC/DC converter topology with DC fault current blocking capability. Replacement of semiconductor switches with full bridge cells allows instant reversal of voltage polarities to limit rapid capacitor discharge and machine inductive currents.

A number of concepts have been proposed to meet future aircraft performance goals. One such concept under consideration is Turboelectric Distributed Propulsion (TeDP) featuring a large number of superconducting motors powered by two superconducting generators placed on each wingtip and connected through a DC distribution network. A key aspect in any design concept is the ability to prove that the system will exhibit a satisfactory reliability for all intended operating conditions. A common tool to support the calculation of failure rates and reliability is Fault Tree Analysis (FTA), and this will be utilized within this paper. The paper undertakes an architectural level FTA on a NASA proposed TeDP architecture to identify any significant factors contributing to the failure rate of key functionalities within the network.

The development of the More-Electric Engine (MEE) concept will see an expansion in the power levels, functionality and criticality of electrical systems within engines. However, to date, these more critical electrical systems have not been accounted for in existing engine certification standards. To begin to address this gap, this paper conducts a review of current engine certification standards in order to determine how these standards will impact on the design requirements of More-Electric Engine (MEE) electrical system architectures. The paper focuses on determining two key architectural requirements: the number of individual failures an architecture can accommodate and still remain functional and the rate at which these failures are allowed to occur.

The Turboelectric Distributed Propulsion (TeDP) concept uses gas turbine engines as prime movers for generators whose electrical power is used to drive motors and propulsors. For this NASA N3-X study, the motors, generators, and DC transmission lines are superconducting, and the power electronics and circuit breakers are cryogenic to maximize efficiency and increase power density of all associated components. Some of the protection challenges of a superconducting DC network are discussed such as low natural damping, superconducting and quenched states, and fast fault response time. For a given TeDP electrical system architecture with fixed power ratings, solid-state circuit breakers combined with superconducting fault-current limiters are examined with current-source control to limit and interrupt the fault current.

The utilization of converter interfaces has the potential to significantly alter the protection system design requirements in future aircraft platforms. However, the impact these converters will have can vary widely, depending on the topology of converter, its filter requirements and its control strategy. This means that the precise impact on the network fault response is often difficult to quantify. Through the analysis of example converter topologies and literature on the protection of DC networks, this paper tackles this problem by identifying key design characteristics of converters which influence their fault response. Using this information, the converters are classified based on their general fault characteristics, enabling potential protection issues and solutions to be readily identified. Finally, the paper discusses the potential for system level design benefits through the optimisation of converter topology and protection system design.

With the diversity of mission capability and the associated requirement for more advanced technologies, designing modern unmanned aerial vehicle (UAV) systems is an especially challenging task. In particular, the increasing reliance on the electrical power system for delivering key aircraft functions, both electrical and mechanical, requires that a systems-approach be employed in their development. A key factor in this process is the use of modeling and simulation to inform upon critical design choices made. However, effective systems-level simulation of complex UAV power systems presents many challenges, which must be addressed to maximize the value of such methods. This paper presents the initial stages of a power system design process for a medium altitude long endurance (MALE) UAV focusing particularly on the development of three full candidate architecture models and associated technologies.

This paper analyses the behaviour of a highly-capacitive DC UAV network under fault conditions. Through simulation, the nature of overvoltage transients caused by the redistribution of stored energy following the clearance of a fault is illustrated. It is found that clearance of fault currents at or around their peak magnitude can result in substantial quantities of inductive energy being redirected into the smaller load capacitors, causing severe overvoltages across these loads. Recommendations for a protection strategy are given on the basis of the results presented, with consideration given to the use of surge arrestors to provide additional overvoltage protection to sensitive loads.