Search Results

Since the Euro VI/6 regulation came into force in 2013/2014, most of the Diesel applications are equipped with both selective catalytic reduction (SCR) systems and Diesel particulate filters (DPF). On the one hand, SCR requires ammonia for the reduction of nitrogen oxides (NOx) created during the combustion process. An aqueous urea solution (AUS) containing 32.5% wt. urea, such as AdBlue® is injected into the hot exhaust gas upstream of the SCR catalyst to produce ammonia for NOx reduction. On the other hand, DPF demonstrates very high particle filtration efficiency, but requires to be periodically regenerated at high temperature to burn off accumulated soot. The regeneration temperature and duration can be significantly lowered by using fuel additives (fuel-borne catalyst or FBC) or by washcoating a catalyst into the DPF (catalyzed DPF or cDPF).

The more and more stringent regulations on particle emissions at the vehicle tailpipe have led the car manufacturers to adopt suitable emissions control systems, like particulate filters with average filtration efficiency that can exceed 99%, including particulate mass (PM) and number (PN). However, there are still some specific operating conditions that could exhibit noticeable particle number emissions. This paper aims to identify and characterize these persistent sources of PN emissions, based on tests carried out both at the engine test bench and at the chassis dynamometer, and both for Diesel and Gasoline direct injection engines and vehicles. For Diesel engines, highest particle numbers were observed downstream of the catalyzed DPF during some operation conditions like engine warm up or filter regeneration phases. PN could be 50 times higher during the warm up phase and can reach as much as 2000 to 3000 times more during the regeneration phase compared to normal operation.

Current progress in the development of diesel engines substantially contributes to the reduction of NOx and Particulate Matter (PM) emissions but will not succeed to eliminate the application of Diesel Particulate Filters (DPFs) in the future. In the past we have introduced a Multi-Functional Reactor (MFR) prototype, suitable for the abatement of the gaseous and PM emissions of the Low Temperature Combustion (LTC) engine operation. In this work the performance of MFR prototypes under both conventional and advanced combustion engine operating conditions is presented. The effect of the MFR on the fuel penalty associated to the filter regeneration is assessed via simulation. Special focus is placed on presenting the performance assessment in combination with the existing differences in the morphology and reactivity of the soot particles between the different modes of diesel engine operation (conventional and advanced). The effect of aging on the MFR performance is also presented.

Lean-burn combustion in SI engines can significantly reduce fuel consumption but NOx reduction becomes challenging because classic three-way catalyst (TWC) is no more efficient. Urea-SCR is then an interesting alternative solution because of its high NOx conversion efficiency without any additional fuel consumption. The coupling between two SI lean-burn engines (stratified and homogeneous combustion) and a urea-SCR catalyst was simulated on the NEDC cycle. Simulation results showed that the SCR efficiency would comply with the limits required by future Euro 5/6 regulations. Associated urea solution consumptions were estimated thanks to a simplified model. Finally, a comparison with a Diesel application was also made. It showed that the required amount of reducing agent remained significantly higher for SI lean-burn engines than for Diesel engine.

To comply with ever more stringent emission limits, engineers are studying and optimising gasoline engine start-up and warm-up phases. Secondary air injection (SAI) represents one option to reduce emissions by post-oxidizing products of a rich combustion like HC, CO and H2. With this approach, the faster catalytic converter light-off allowed by the increase in exhaust temperature leads to a significant HC emissions reduction. All the mechanisms involved in post oxidation downstream of the exhaust valve are not well-known. In order to achieve substantial improvements, various SAI strategies were studied with a conventional PFI gasoline engine. Tests have been carried out both on steady-state running conditions and on transient warm-up phases at engine test bench. Various specific experimental devices and methodologies were developed. For example, the use of fast HC and temperature measurements is coupled with exhaust gas flow rate modeled with system simulation.

This paper presents the detailed characterization of particulate emissions from a NADI™ dual mode engine (HCCI at low load and conventional combustion at high load). Morphology, composition and chemical reactivity of the particulate matter generated on an engine running in HCCI mode have been specified and compared to the conventional mode reference. Results showed that HCCI combustion formed particles with a higher volatile organic fraction due to the relatively high level of HC generated by this kind of combustion. Advanced soot characterization emphasized that HCCI soot is oxidized at a slower reaction rate than conventional soot, but with a lower temperature. This last characteristic could partially compensate the poor continuous regeneration effect due to low NO2 emission levels observed in HCCI combustion. Microscopic observation and particle sizing did not show significant differences between HCCI and conventional soot.

The reduction of NOx emissions required by the future Euro 6 standards leads engine manufacturers to develop Diesel Homogeneous Charge Compression Ignition (HCCI) combustion processes. Because this concept allows reducing both NOx and particulates simultaneously, it appears as a promising way to meet the next environmental challenges. Unfortunately, HCCI combustion often increases CO and HC emissions. Conventional oxidation catalyst technologies, currently used for Euro 4 vehicles, may not be able to convert these emissions because of the saturation of active catalytic sites. As a result, such increased CO and HC emissions have to be reduced under standard levels using innovative catalysts or emergent technologies. The work reported in this paper has been conducted within the framework of the PAGODE project (PSA, IFP, Chalmers University, APTL, CRF, Johnson Matthey and Supelec) and financed by the European Commission.