Search Results

The measurement of the two-color line of sight soot and KL factor for NO.2 diesel and jet-A fuels was conducted in an optical constant volume combustion chamber by using a high speed camera under 1000 K ambient temperature and varied oxygen concentration conditions. The ambient conditions were set as follows: four oxygen cases including 10%, 15%, 18% and 21% at 1000 K ambient temperature. KL factor and soot temperature were determined based on the two-color pyrometry technique using two band-pass filters with wavelengths of 650 nm and 550 nm. The results show that low soot temperature is observed in the upstream inner flame along the centerline, which is surrounded by high soot temperature regions, and a high KL factor is found in the same region with a low soot temperature.

This paper investigates the combustion of biodiesel and diesel in an optical accessible constant volume chamber that can simulate the conditions in compression ignition engines. The high-pressure and high-temperature environment in the chamber was generated by a controlled premixed combustion with desired content of oxygen left. A common rail and an injector with 160 degree included angle were used to deliver the fuel. Ultra low sulfur diesel (ULSD) and biodiesel from used cook oil were used in this paper. High speed imaging of natural luminosity from the flame was used to study the combustion flame in a time resolved manner. A combination of high speed and intensified imaging of OH chemiluminescence was employed to identify reaction zones. This method has the advantage of capturing the global pictures, thus allowing the studying of jet-to-jet variations, while it does not sacrifice the time-resolved resolution.

An optically accessible single-cylinder high-speed direct-injection (HSDI) diesel engine equipped with a Bosch common rail injection system was used to study effects of injection pressures on the in-cylinder spray and combustion processes. An injector with an injection angle of 70 degrees and European low sulfur diesel fuel (cetane number 54) were used in the work. The operating load was 2.0 bar IMEP with no EGR added in the intake. The in-cylinder pressure was measured and the heat release rate was calculated. High-speed Mie-scattering technique was employed to visualize the liquid distribution and evolution. High-speed combustion video was also captured for all the studied cases using the same frame rate. NOx emissions were measured in the exhaust pipe. The experimental results indicated that for all of the conditions the heat release rate was dominated by a premixed combustion pattern. Two-stage low temperature reaction was seen for early injection timings.

An optically accessible single-cylinder high-speed direct-injection (HSDI) Diesel engine equipped with a Bosch common rail injection system was used to study the spray and combustion processes for European low sulfur diesel, bio-diesel, and their blends at different blending ratio. Influences of injection timing and fuel type on liquid fuel evolution and combustion characteristics were investigated under similar loads. The in-cylinder pressure was measured and the heat release rate was calculated. High-speed Mie-scattering technique was employed to visualize the liquid distribution and evolution. High-speed combustion video was also captured for all the studied cases using the same frame rate. NOx emissions were measured in the exhaust pipe. The experimental results indicated that for all of the conditions the heat release rate was dominated by a premixed combustion pattern and the heat release rate peak became smaller with injection timing retardation for all test fuels.

Combustion processes employing different injection strategies in a High-Speed Direct Inject (HSDI) diesel engine were investigated using a narrow angle injector (70 degree). Whole-cycle combustion was visualized using a high-speed digital video camera. The liquid spray evolution process was imaged by the Mie-scattering technique. Different injection strategies were employed in this study including early pre-Top Dead Center (TDC) injection, post-TDC injection, multiple injection strategies with an early pre-TDC injection and a late post-TDC injection. Smokeless combustion was obtained under some operating conditions. Compared with the original injection angle (150 degree), some new combustion phenomena were observed for certain injection strategies. For early pre-TDC injection strategies, liquid fuel impingement is observed that results in some newly observed fuel film combustion flame (pool fires) following an HCCI-like weak flame.

Low Temperature Compression Ignition (LTCI) combustion employing multiple injection strategies in an optically accessible single-cylinder small-bore High-Speed Direct-Injection (HSDI) diesel engine equipped with a Bosch common-rail electronic fuel injection system was investigated in this work. Heat release characteristics were analyzed through the measurement of in-cylinder pressure. The whole cycle combustion process was visualized with a high-speed digital video camera by imaging natural flame luminosity and three-dimensional like combustion structures were obtained by taking flame images from both the bottom of the optical piston and the side window. The transient in-cylinder late cycle soot distribution was obtained by applying a Backward Illumination Light Extinction (BILE) technique through side windows. Based on the flame luminosity and soot spatially integrated signal, new parameters were defined to evaluate the combustion performance and soot formation characteristics.

As engine researchers are facing the task of designing more powerful, more fuel efficient and less polluting engines, a large amount of research has been focused towards homogeneous charge compression ignition (HCCI) operation for diesel engines. Ignition timing of HCCI operation is controlled by a number of factors including intake temperatures, exhaust gas recirculation (EGR) and injection timing to name a few. This study focuses on the computational modeling of an optically accessible high-speed direct-injection (HSDI) small bore diesel engine. In order to capture the phenomena of HCCI operation, the KIVA computational code package has been outfitted with an improved and optimized Shell autoignition model, the extended Zeldovich thermal NOx model, and soot formation and oxidation models. With the above named models in place, several cases were computed and compared to experimentally measured data and captured images of the DIATA test engine.

An optically accessible single cylinder small-bore HSDI diesel engine equipped with a Bosch common-rail injection system was used to study the effects of multiple injection strategies on the in-cylinder combustion processes. The operating conditions were considered typical in the metal engine under moderate load conditions. In-cylinder pressure traces are used to analyze heat release characteristics. The combustion modes transit from the Homogeneous Charge Compression Ignition (HCCI)-like combustion mode to conventional diesel combustion by changing injection parameters. The whole cycle combustion process was visualized through a high-speed digital video camera and the combustion images clearly show the combustion mode transition. Laser-Induced Exciplex Fluorescence (LIEF) technique was used to obtain simultaneous liquid and vapor fuel distributions within the combustion chamber, with tetradecane-TMPD-naphthalene as the base fuel-dopant combination.

Homogeneous Charge Compression Ignition (HCCI) combustion employing single main injection strategies in an optically accessible single cylinder small-bore High-Speed Direct Injection (HSDI) diesel engine equipped with a Bosch common-rail electronic fuel injection system was investigated in this work. In-cylinder pressure was taken to analyze the heat release process for different operating parameters. The whole cycle combustion process was visualized with a high-speed digital camera by imaging natural flame luminosity. The flame images taken from both the bottom of the optical piston and the side window were taken simultaneously using one camera to show three dimensional combustion events within the combustion chamber. The engine was operated under similar Top Dead Center (TDC) conditions to metal engines. Because the optical piston has a realistic geometry, the results presented are close to real metal engine operations.

An optically-accessible single cylinder small-bore HSDI diesel engine equipped with a Bosch common-rail injection system is used to study the effects of differing injection strategies on combustion and soot. Laser-Induced Incandescence (LII) is used to visualize the evolution and distribution of soot within the combustion chamber from the onset of ignition to late into the expansion stroke. A low-sooting fuel, blended from two single component fuels, is used for experimentation. Because of the low-sooting nature of the fuel blend, the lean operating conditions, and optical distortion of the complex shaped engine, acceptable LII signal levels are difficult to obtain. Therefore a low-sulfur European Diesel fuel is also employed during experimentation. Acceptable LII signal levels are obtained using the Diesel fuel, however, without extreme caution, surface damage to the optical components of the engine are possible.