Search Results

Active regeneration systems for cleaning diesel exhaust can operate at extremely high temperatures up to 1000°C. The extremely high temperatures create a unique challenge for the design of regeneration structural components near their melting temperatures. In this paper, the preparation of the sheet specimens and the test set-up based on induction heating for sheet specimens are first presented. Tensile test data at room temperature, 500, 700, 900 and 1100°C are then presented. The yield strength and tensile strength were observed to decrease with decreasing strain rate in tests conducted at 900 and 1100°C but no strain rate dependence was observed in the elastic properties for tests conducted below 900°C. The stress-life relations for under cyclic loading at 700 and 1100°C with and without hold time are then investigated. The fatigue test data show that the hold time at the maximum stress strongly affects the stress-life relation at high temperatures.

A modern definition of quality control and improvement is the reduction of variability in processes and products. The reduced variability can be directly translated into lower costs, better functions and fewer repairs. However, the final quality of processes and products is sometimes derived from other measured variables through some implicit or explicit functional relationships. Sometimes, a tiny uncertainty in a variable can produce a huge uncertainty in a derived quantity. Therefore, the propagation of uncertainty needs to be understood and the individual variables need to be well controlled. More importantly, the critical factors that affect quality the most should be identified and thoroughly investigated. Design of experiments and statistical control plays central roles in finding root cause of failure, reduction of variability and quality improvement.

Durability/reliability design of products, such as auto exhaust systems, is essentially based on the observation of test data and the accurate interpretation of these data. Therefore, test planning and related data analysis are critical to successful engineering designs. To facilitate engineering applications, testing and data analysis methods have been standardized over the last decades by several standard bodies such as the American Society for Testing and Materials (ASTM). However, over the last few years, several effective testing and data analysis methods have been developed, and the existing standard procedures need to be updated to incorporate the new observations, knowledge, and consensus. In this paper, the common practices and the standard test planning and data analysis procedures are reviewed first. Subsequently, the recent development in accelerated testing, equilibrium based data fitting, design curve construction, and Bayesian statistical data analysis is presented.

High-temperature thermal-mechanical systems are considered as an indispensable solution to modern vehicle emission control. Such systems include advanced engines, manifolds, thermal regeneration systems, and many other systems. Creep, fatigue, oxidation, or their combinations are the fundamental underlying material degradation and failure mechanisms in these systems subjected to combined thermal and mechanical loadings. Therefore, the basic understanding and modeling of these mechanisms are crucial in engineering designs. In this paper, the state-of-the-art methods of damage/failure modeling and life assessment for components under thermal-fatigue loading, are reviewed first. Subsequently, a new general life assessment procedure is developed for components subjected to variable amplitude thermal- and mechanical- loadings, with an emphasis on hold-time effect and cycle counting.

There is a broad range of material choices for on-road and off-road exhaust systems. The final selection of the materials depends on the balance of engineering performance of the materials and the cost. Thermal-cycling resistance of exhaust materials is an extremely important criterion for the long-term durability and reliability performance of very high temperature exhaust components and systems. To optimize the thermal-cycling resistance and cost of those materials, a selection matrix must be established. Several material evaluation and selection matrices are already available, however, these are not sufficient to meet the industry needs. The current procedure of material selection is essentially based on the trial-and-error approach, which is not efficient in the current market environment. In this paper, a general rational approach for thermal-cycling resistance characterization and ranking is demonstrated.

Durability and reliability performance is one of the most important concerns of a recently developed Thermal Regeneration Unit for Exhaust (T.R.U.E-Clean®) for exhaust emission control. Like other ground vehicle systems, the T.R.U.E-Clean® system experiences cyclic loadings due to road vibrations leading to fatigue failure over time. Creep and oxidation cause damage at high temperature conditions which further shortens the life of the system and makes fatigue life assessment even more complex. Great efforts have been made to develop the ability to accurately and quickly assess the durability/reliability of the system in the early development stage. However, reliable and validated simplified engineering methods with rigorous mathematical and physical bases are still urgently needed to accurately manage the margin of safety and decrease the cost, whereas iterative testing is expensive and time consuming.

Fatigue, creep, oxidation, or their combinations have long been recognized as the principal failure mechanisms in many high-temperature applications such as exhaust manifolds and thermal regeneration units used in commercial vehicle aftertreatment systems. Depending on the specific materials, loading, and temperature levels, the role of each damage mechanism may change significantly, ranging from independent development to competing and combined creep-fatigue, fatigue-oxidation, creep-fatigue-oxidation. Several multiple failure mechanisms based material damage models have been developed, and products to resist these failure mechanisms have been designed and produced. However, one of the key challenges posed to design engineers is to find a way to accelerate the durability and reliability tests of auto exhaust in component and system levels and to validate the product design within development cycle to satisfy customer and market's requirements.

A design curve, such as a fatigue design S-N curve, is required in engineering design processes. The design curve is usually constructed by analyzing test data, which often exhibit relatively large scatter. For assumed linear test data, two-stress level test plan is commonly used for accelerated life testing (ALT) and subsequent design curve construction. In this paper, based on the two-stress level test plan, a tolerance limit approach is adopted to develop a simple design curve construction procedure. The predicted results from the new method are compared with that of other methods. The advantage of the new method is demonstrated by analyzing the fatigue S-N test data of exhaust components. The determination of minimum sample size is also discussed with a worked table and a graph.