Search Results

An improvement of thermal efficiency of internal combustion engines is strongly required. Meanwhile, from the viewpoint of refinery, CO2 emissions and gasoline price decrease when lower octane gasoline can be used for vehicles. If lower octane gasoline is used for current vehicles, fuel consumption rate would increase due to abnormal combustion. However, if a Homogeneous Charge Compression Ignition (HCCI) engine were to be used, the effect of octane number on engine performance would be relatively small and it has been revealed that the thermal efficiency is almost unchanged. In this study, the engine performance estimation of HCCI combustion using lower octane gasoline as a vision of the future engine was achieved. To quantitatively investigate the fuel consumption performance of a gasoline HCCI engine using lower octane fuel, the estimation of fuel consumption under different driving test cycles with different transmissions is carried out using 1D engine simulation code.

In Biodiesel Fuel Research Working Group(WG) of Japan Auto-Oil Program(JATOP), some impacts of high biodiesel blends have been investigated from the viewpoints of fuel properties, stability, emissions, exhaust aftertreatment systems, cold driveability, mixing in engine oils, durability/reliability and so on. In the impact on exhaust emissions, the impact of high biodiesel blends into diesel fuel on diesel emissions was evaluated. The wide variety of biodiesel blendstock, which included not only some kinds of fatty acid methyl esters(FAME) but also hydrofined biodiesel(HBD) and Fischer-Tropsch diesel fuel(FTD), were selected to evaluate. The main blend level evaluated was 5, 10 and 20% and the higher blend level over 20% was also evaluated in some tests. The main advanced technologies for exhaust aftertreatment systems were diesel particulate filter(DPF), Urea selective catalytic reduction (Urea-SCR) and the combination of DPF and NOx storage reduction catalyst(NSR).

Clarifying the impact of ETBE 8% blended fuel on current Japanese gasoline vehicles, under the Japan Clean Air Program II (JCAPII) we conducted exhaust emission tests, evaporative emission tests, durability tests on the exhaust after-treatment system, cold starting tests, and material immersion tests. ETBE 17% blended fuel was also investigated as a reference. The regulated exhaust emissions (CO, HC, and NOx) didn't increase with any increase of ETBE content in the fuel. In durability tests, no noticeable increase of exhaust emission after 40,000km was observed. In evaporative emissions tests, HSL (Hot Soak Loss) and DBL (Diurnal Breathing Loss) didn't increase. In cold starting tests, duration of cranking using ETBE 8% fuel was similar to that of ETBE 0%. In the material immersion tests, no influence of ETBE on these material properties was observed.

The effects of Injector deposits, Combustion Chamber Deposits (CCD), and Intake Valve Deposits (IVD) on exhaust emissions, fuel economy and vehicle performances have long been recognized in engine and fuel/detergent design. Because important elements of engine design such as injector position, exhaust gas recirculation (EGR) ratio, and air fuel ratio (AFR) differ from those of port fuel injection (PFI) engines, current existing test methods are not applicable. Therefore, the demand has been increasing year by year for specific evaluation methods for vehicles with direct injection spark ignition (DISI) engines which have spread rapidly worldwide. Oil and Auto Cooperation for International Standards (OACIS) of Japan selected the Mitsubishi DISI engine (4G93-1.8L) [1] and conducted engine bench tests to investigate the effects of deposits on operating conditions at 40km/h, 70km/h, 140km/h and WOT.

The effects of injector deposits, combustion chamber deposits (CCD), and intake valve deposits (IVD) on exhaust emissions, fuel economy and engine performance have long been recognized in engine and fuel/detergent design. Because important elements of the engine design such as injector position, exhaust gas recirculation (EGR) ratio, and air fuel ratio (AFR) differ from those in port fuel injection (PFI) engines, direct injection spark-ignition (DISI) engines require specific evaluation methods. However, little data is available regarding engine deposits in the more recently produced DISI engines.

The effects of engine and after-treatment control conditions on emissions fluctuation were evaluated and the technical idea for improving the repeatability in tailpipe emission measurement from DISI vehicles was provided. To improve measurement repeatability, low emissions analyzers with dilution air refining system were employed for this research. In addition, a new device that enabled monitoring of signals from the Engine Control Unit (ECU) was developed. A novel approach using these devices was applied to DISI gasoline engine vehicles equipped with de-NOx catalyst to clarify emission characteristics in the Japanese 10.15 test cycle emission tests. Through the tests, it is found that NOx emissions most correlated with the temperature at the de-NOx catalyst. CO and HC reaching the de-NOx catalyst played an important role in the temperature increase of de-NOx catalyst by exothermic reactions.

Exhaust emissions of nitrogen oxide (NOx), total hydrocarbons (THC) and carbon mono-oxide (CO) in terms of sulfur concentration were mainly investigated according to the Japanese 10.15 mode driving schedule. Tested vehicles had direct injection engines with nitrogen oxide (NOx) selective reduction catalyst or NOx storage reduction catalyst as well as stoichiometric combustion engines with three-way catalyst. Direct continuous measurement of NOx, THC and CO was also conducted. Exhaust Emissions were measured using He injection and mass spectrometry. The air fuel ratio (AFR) and driving conditions that would promote sulfur removal were found to be important factors in reducing NOx further, for recent gasoline-fueled vehicles with emerging technologies using low sulfur fuels under 100 ppm.

Evaporative emissions of Japanese older and current vehicles (1990-1998MY) and U.S. current vehicles, which were adapted to federal regulations in 1996, were investigated using typical Japanese gasoline. Japanese older and current vehicles exhibited high levels of Running Loss (RL), Hot Soak Loss (HSL) and Diurnal Breathing Loss (DBL), and their emissions showed strong Reid vapor pressure (RVP) dependence. On the other hand, U.S. vehicles showed very weak RVP dependence, between 62kPa and 76kPa. Their emissions also showed very low levels of RL, HSL and DBL. These results suggest RVP reduction is just effective for Japanese older and current vehicles. Evaporative emissions of Japanese and U.S. vehicles were also tested according to a new Japanese test procedure and the 35 degrees centigrade RL test procedure. In the case of the RL and DBL tests, the impact of test conditions on evaporative emissions was discussed as well.