Search Results

A novel combined power and cooling cycle based on the Organic Rankine Cycle (ORC) and the Compression Refrigeration Cycle (CRC) is proposed. The cycle can be driven by the exhaust heat from a diesel engine. In this combined cycle, ORC will translate the exhaust heat into power, and drive the compressor of CRC. The prime advantage of the combined cycle is that both the ORC and CRC are trans-critical cycles, and using CO₂ as working fluid. Natural, cheap, environmentally friendly, nontoxic and good heat transfer properties are some advantages of CO₂ as working fluid. In this paper, besides the basic combined cycle (ORC-CRC), another three novel cycles: ORC-CRC with an expander (ORC-CRCE), ORC with an internal heat exchanger as heat accumulator combined with CRC (ORCI-CRC), ORCI-CRCE, are analyzed and compared.

Due to the mechanical forces under static conditions, the engine cylinders cross section will not be a round circle any more once they are installed. The deformation of an engine cylinder causes increasing lubricating oil consumption and abnormal wear, resulting in worse fuel economy and emissions. However, prediction of deformation on a liner has not been made because of the complication of conditions and structure. In this study, a V6-type engine body model was built and meshed with Hypermesh suit software. Then, cylinder deformation under static condition has been simulated and analyzed. First of all, experimental work was done to verify the engine model. Basically, few parameters like pre-tightened force, structure and distribution of bolts have been investigated to figure out how the cylinder bore deformation behaves via finite element analysis. Also, a simple Matlab program was developed to process the data.

In this paper, the influence of sulfur and ash fraction of lubricating oil on particle emissions was investigated via experimental works. Especially, we focus on the characterizations like size distribution, morphology and element composition in diesel particles. All of the research was done on a two-cylinder diesel engine under different load conditions. Five kinds of lubricating oils with different levels of sulfur and ash fraction were used in this study, among which a kind of 5W-30 (ACEA, C1) oil was used as baseline oil. Diesel primary particles were collected by thermophoretic system, and analyzed by transmission electron microscopy and energy dispersive X-ray spectrum technique, respectively. Conclusions drawn from the experiments indicate that the sulfur and ash change the primary particle emissions directly.

Impingement of spray against the cylinder wall or piston bowl is an unavoidable physical process in homogeneous charge compression ignition (HCCI) and premixed charge compression ignition (PCCI) engines using early injection strategy. It directly affects fuel-air mixture formation, combustion and exhaust emission. In addition, the alcohol fuels such as methanol, ethanol and n-butanol are regarded as hopeful alternative fuels as well as fuel additive for HCCI and PCCI diesel engines to improve the emission level. The better understanding for the effect of alcohol-diesel blending fuel on the spray-wall impingement process is helpful for the improvement of HCCI and PCCI diesel engines. In this paper, the effects of three different alcohol-diesel blending fuels (methanol, ethanol and n-butanol) on the spray-wall impingement process were studied. Numerical investigation was performed in AVL FIRE code.

Power lithium-ion battery is the core component of electric vehicles and hybrid electric vehicles (EVs and HEVs). Thermal management at different operating conditions affects the life, security and stability of lithium-ion battery pack. In this paper, a one-dimensional, multiscale, electrochemical-thermal coupled model was applied and perfected for a flat-plate-battery pack. The model is capable of predicting thermal and electrochemical behaviors of battery. To provide more guidance for the selection of thermal management, temperature evolutions and distributions in the battery pack at various ambient temperatures, discharge rates and thermal radiation coefficients were simulated based on six types of thermal management (adiabatic, natural convection, air cooling, liquid cooling, phase change material cooling, isothermal).

According to the study of the soot emission in the combustion of diesel,a new reduced mechanism for n-Heptane was constructed to describe the combustion process in diesel engine by using sensitivity analysis.Furthermore,verifying the ignition delay time in combustion process by using CHEMKIN PRO in different pressure of 13.5 atm and 42 atm, initial temperatures of 600k and equivalence ratio of 0.5 and 1.0.Then,compare the simulated results with the experiment data, the mechanisms used in the simulation were Lawrence Livermore National Laboratory (LLNL) detail mechanism and the State Key Laboratory of Engine (SKLE) mechanism.

Currently, selective catalytic reduction (SCR) is one of the main after-treatment systems to control diesel engine NOx emission. But the SCR system is bulky, considering the limited installation space. Therefore, the design of SCR system with the compact structure and reliable performance is one of the essential topics. In this study, the structure parameters, such as catalyst cross-sectional area, catalyst length, substrate wall thickness, coating thickness, channels per square inch (CPSI) of substrate, are taken into consideration to study their effects on the SCR performance and narrow the scope of various structural parameters for the following optimization study. Then, the structural parameters of the SCR reactor are optimized by considering the coupling relationship among these structural parameters by using the Response Surface Methodology (RSM) at high load of diesel engine.

In this paper, the influences of metallic content of lubricating oils on diesel particles were investigated. Three lubricating oils with different levels of metallic content were used in a 2.22 Liter, two cylinders, four stroke, and direct injection diesel engine. 4.0 wt. % and 8 wt. % antioxidant and corrosion inhibitor (T202) were added into baseline lubricating oil to improve the performance respectively. Primary particle diameter distributions and particle nanostructure were compared and analyzed by Transmission Electron Microscope. The graphitization degrees of diesel particles from different lubricating oils were analyzed by Raman spectroscopy. Conclusions drawn from the experiments indicate that the metallic content increases the primary particles diameter at 1600 rpm and 2200 rpm. The primary particles diameter ranges from 5 nm to 65 nm and the distribution conformed to Gaussian distribution.

Spray impacting on a lube oil film with a finite thickness is a common phenomenon in IC engines and plays a critical role in the fuel-air mixture process and combustion. With the use of early injection strategy to achieve HCCI combustion mode in diesel engines, this phenomenon becomes more and more prominent. In addition, oxygenated fuels such as methanol and ethanol are regarded as alternative fuel and additives to improve the overall performance of HCCI engine. Therefore, a better understanding about the role of lube oil film thickness in methanol-diesel and ethanol-diesel blended fuels spray/wall impingement is helpful for accumulating experimental data to establish a more accurate spray/wall impingement model and optimize the combustion in HCCI engines. In this paper, the effect of lube oil film thickness on the characteristics of spray/wall impingement of different fuels are investigated in a constant volume bomb test system.

In this study, the effect of volatile fractions from engine lubricating oil on diesel particle emissions were studied experimentally. One commercial CF lubricating oil was used and distilled to subtract the different volatile fractions with boiling temperature of 220 °C, 260 °C and 300 °C, respectively. Oils derived from this distillation process were applied as the lubricating oil and following engine experiments were conducted. Diesel primary particles were sampled with a costume designed thermophoretic system. A fast response particulate spectrum equipment was employed to study the size distribution and number concentration of particles in the exhaust. Transmission electron microscopy was used to characterize the size distribution of the primary diesel particles relates to different oil volatile fractions.

A two-dimensional mesoscopic approach has been developed to investigate the flow and soot loading in the micro-channels of diesel particulate filter. Soot particle size examined is in the range of 10 nm to 10 μm. The flow is solved by an incompressible lattice Boltzmann model and the transport of solid particle is described in a Lagrangian frame of reference by cell automation probabilistic model. The lattice Boltzmann-cell automation probabilistic model (LB-CA model) is validated with the results of previous studies. The heterogeneous porous wall of DPF is generated by quartet structure generation set (QSGS). The effects of porous wall on the pressure field and velocity field are investigated. The distribution and deposition of soot particles with different sizes in clean channels are simulated. The dynamic evolution of solid boundary in soot particle capture process is investigated and the effects of the deposited soot particles on flow field are evaluated.

The combined thermo-generator and organic rankine cycle (TEG-ORC) used in exhaust heat recovery of internal combustion engine (ICE) is analyzed theoretically. Only about one third of the total energy released from fuel combustion is converted into useful work in engines, while the remaining energy goes into ambient environment, among which exhaust gas possesses high-grade thermal energy. Most of previous studies on energy recovery from engines have focused on exhaust heat recovery by ORC. However, if the heat is exchanged directly with high-temperature exhaust gas, organic working fluid would resolve with its lower decomposition temperature, and this is extremely harmful to ORC system. To avoid this phenomenon and utilize waste heat, preliminary thermoelectric modules are used to lower exhaust temperature and to generate electricity simultaneously.

Cepstrum analysis method is an important part in the area of modern signal processing subject, which has a good application in noise source identification. The paper uses cepstrum method to analyze noise and vibration signals of diesel engine, separates and extracts periodic source signals with characteristic of non-harmonic order from complex spectrum waveform, and then identifies the contribution of each component to the spectrum with characteristic of non-harmonic order by analyzing noise and vibration signals of each component. The result shows that cepstrum analysis method can extract source signal from the complex spectrum waveform effectively, thus facilitate the identification of noise and vibration sources.

This paper presents a method to identify the radiation noise source of diesel engine based on a Cepstrum Analysis (CA) and Analytic Hierarchy Process (AHP). Through measuring noise and surface vibrations of a diesel engine, cepstrum analysis is applied to the measured signals. In an investigation of the radiation noise source, the hierarchy tree and judgment matrix are given. Through identification, the main noise source is found. The results show that the left body contributes maximally to non-harmonic spectral characteristics of noise. Therefore, in order to reduce engine vibration and noise effectively, we should optimize and improve left body. In addition, optimizing and improving gear chamber casing, oil pan, inlet pan and valve chamber cover can decrease harmonic vibration and noise of engine.

We studied the influence of extreme pressure (EP) antiwear additive on the emission and distribution of particulate matters (PMs), since EP antiwear additive is necessary to improve the property of lubricating oil with the downsizing development of engines. We used a four-cylinder, turbocharged, and inter-cooled system with SAE15W-40 lubricant diesel engine. Pure diesel and fuel blends with varying weight percentages (0.5%, 1.0%, and 1.5%) of EP antiwear additive were used. Engine speed increased by increments of 400 from 1,200 rpm to 2,800 rpm under medium load and full load. The DMS500 was used to acquire particle data, and the Wave Book was employed to record oil and cylinder pressure. Conclusions drawn from the experiments suggest that EP antiwear additive has significant effects on PM emissions and distributions. Increments and decrements were observed on the number of accumulation mode particles and nucleation mode particles with BDAW-0.5.

In this paper, the influences of lubricating base oils on diesel particles morphology and nanostructure were investigated. Four different lubricating base oils were blended in diesel at a mass ratio of 0.5% and 1.0% for combustion. Exhaust particle samples generated by a four-cylinder, four-stroke direct injection engine when employing neat diesel and four base oil dosed mixtures as the fuel were collected and compared. Primary particle diameter distributions and particle nanostructure were compared and analyzed by a High-Resolution Transmission Electron Microscope (HRTEM). Conclusions drawn from the experiments indicated that the primary particles diameter ranges from 5 nm to 70 nm and the distribution conformed to typical Gaussian distribution. Base oil II, III, IV increased the primary particles diameter, while particles from base oil I exhibited smaller size than that from neat diesel.

A bottoming waste-heat-recovery (WHR) model based on the Organic Rankine Cycle (ORC) is proposed to recover waste heat from exhaust gas and jacket water of a typical diesel engine (DE). The ORC model is detailed built based upon real structural and functional parameters of each component, and is able to precisely reflect the working process of the experimental ORC system constructed in lab. The DE is firstly tested to reveal its energy balance and the features of waste heat. The bottoming ORC is then simulated based on experimental data from the DE bench test using R245fa and R601a as working fluid. Thermodynamic evaluations are done on key parameters like waste heat recovered, expansion power, pump power loss and system efficiency. Results indicate that maximum expansion power and efficiency of the ORC are up to 18.8kW and 9.6%. Influences of engine condition, fluid mass flow and evaporating pressure on system performance are analyzed and meaningful regularities are revealed.

Spray-wall impingement is an unavoidable physical process in homogeneous charge compression ignition (HCCI) diesel engines using early injection strategy which is the main source for the hydrogen carbon (HC) and monoxide (CO) emissions. Dimethyl ether (DME) is a potential fuel additive to decrease HC and CO emissions due to its higher oxygen content. However, issues relating to structural design and early injection timing mean spray-wall impingement still occurs when using the diesel-DME blended fuels, which directly affect the fuel-air mixture formation in the near wall region and further influence the emission characteristics. The better understanding for the effects of spray-wall impingement parameters on fuel-air mixture formation in near wall region for diesel-DME blended fuels is helpful for the improvement of HC and CO emissions for HCCI diesel engines.

The aim of this research is to investigate the effects of ashless dispersant of lube oils on diesel exhaust particles. Emphasis is placed on particle size, morphology, nanostructure and graphitization degree. Three kinds of lube oils with different percentages of ashless dispersant were used in a two-cylinder diesel engine. Ashless dispersant (T154), which is widely used in petrochemical industry, were added into baseline oil at different blend percentages (4.0% and 8.0% by weight) to improve lubrication and cleaning performance. A high resolution Transmission Electron Microscope (HRTEM) and a Raman spectroscopy were employed to analyze and compare particle characteristics. According to the experiment results, primary particles diameter ranges from 3 nm to 65 nm, and the diameter distribution conformed to Gaussian distribution. When the ashless dispersant was used, the primary particles diameter decrease obviously at both 1600 rpm and 2200 rpm.

A new two-dimensional wall-flow DPF microstructure model has been developed in this paper to investigate the particle deposition distribution in DPF channels and the deep-bed filtration process of DPF. The substrate wall of the DPF having a thickness of L is divided into several layers with a uniform thickness of Δy along the cross-wall direction, and each layer has specific porosity and pore size. The pressure drop, particle deposition distribution and the dynamic deep-bed filtration process of the DPF with inhomogeneous wall structure are studied under various space velocities. Besides, the differences on DPF’s performance brought by the inhomogeneous wall structure are discussed by comparing with a homogeneous wall structure.