Search Results

High-pressure direct-injection (HPDI) in heavy duty engines allows a natural gas (NG) engine to maintain diesel-like performance while deriving most of its power from NG. A small diesel pilot injection (5-10% of the fuel energy) is used to ignite the direct injected gas jet. The NG burns in a predominantly non-premixed combustion mode which can produce particulate matter (PM). Here we study the effect of injection strategies on emissions from a HPDI engine in two parts. Part-I will investigates the effect of late post injection (LPI) and Part II will study the effect of slightly premixed combustion (SPC) on emission and engine performance. PM reductions and tradeoffs involved with gas late post-injections (LPI) was investigated in a single-cylinder version of a 6-cylinder,15 liter HPDI engine. The post injection contains 10-25% of total fuel mass, and occurs after the main combustion event.

High-pressure direct-injection (HPDI) in heavy duty engines allows a natural gas (NG) engine to maintain diesel-like performance while deriving most of its power from NG. A small diesel pilot injection (5-10% of the fuel energy) is used to ignite the direct injected gas jet. The NG burns in a predominantly mixing-controlled combustion mode which can produce particulate matter (PM). Here we study the effect of injection strategies on emissions from a HPDI engine in two parts. Part-I investigated the effect of late post injection (LPI); the current paper (Part-II) reports on the effects of slightly premixed combustion (SPC) on emission and engine performance. In SPC operation, the diesel injection is delayed, allowing more premixing of the natural gas prior to ignition. PM reductions and tradeoffs involved with gas slightly premixed combustion was investigated in a single-cylinder version of a 6-cylinder, 15 liter HPDI engine.

Soot emissions from direct-injection engines are sensitive to the fuel-air mixing process, and may vary between combustion cycles due to turbulence and injector variability. Conventional exhaust emissions measurements cannot resolve inter- or intra-cycle variations in particle emissions, which can be important during transient engine operations where a few cycles can disproportionately affect the total exhaust soot. The Fast Exhaust Nephelometer (FEN) is introduced here to use light scattering to measure particulate matter concentration and size near the exhaust port of an engine with a time resolution of better than one millisecond. The FEN operates at atmospheric pressure, sampling near the engine exhaust port and uses a laser diode to illuminate a small measurement volume. The scattered light is focused on two amplified photodiodes.

This paper examines the combustion and emissions produced using a prototype fuel injector nozzle for pilot-ignited direct-injection natural gas engines. In the new geometry, 7 individual equally-spaced gas injection holes were replaced by 7 pairs of closely-aligned holes (“paired-hole nozzle”). The paired-hole nozzle was intended to reduce particulate formation by increasing air entrainment due to jet interaction. Tests were performed on a single-cylinder research engine at different speeds and loads, and over a range of fuel injection and air handling conditions. Emissions were compared to those resulting from a reference injector with equally spaced holes (“single-hole nozzle”). Contrary to expectations, the CO and PM emissions were 3 to 10 times higher when using the paired-hole nozzles. Despite the large differences in emissions, the relative change in emissions in response to parametric changes was remarkably similar for single-hole and paired-hole nozzles.

In direct-injection engines, combustion and emission formation is strongly affected by injection quality. Injection quality is related to mass-flow rate shape, momentum rate shape, stability of pulses as well as mechanical and hydraulic delays associated with fuel injection. Finding these injector characteristics aids the interpretation of engine experiments and design of new injection strategies. The goal of this study is to investigate the rate of momentum for the single and post injections for high-pressure direct-injection natural gas injectors. The momentum measurement method has been used before to study momentum rate of injection for single and split injections for diesel sprays. In this paper, a method of momentum measurement for gas injections is developed in order to present transient momentum rate shape during injection timing. In this method, a gas jet impinges perpendicularly on a pressure transducer surface.

Compression ignition engines, including those that use natural gas as the major fuel, produce emissions of NOx and particulate matter (PM). Westport Inc. has developed the pilot-ignited high-pressure direct-injection (HPDI) natural gas engine system. Although HPDI engines produce less soot than comparable conventional diesel engines, further reductions in engine-out soot emissions is desired. In diesel engines, multiple injections can help reduce both NOx and PM. The effect of post injections on HPDI engines was not studied previously. The present research shows that late injection of a second gas pulse can significantly reduce PM and CO from HPDI engines without significantly increasing NOx or fuel consumption. In-cylinder pressure measurements were used to characterize the heat release resulting from the multiple injections. Experiments showed that most close-coupled split injection strategies provided no significant emissions benefit and less stable operation.

The scattering properties (influenced by morphology) and refractive index (dependent on microstructure) of engine-emitted soot influences its effect on climate, as well as how we interpret optical measurements of aerosols. The morphology and microstructure of soot from two different engines were studied. The soot samples were collected from a 1.9L Volkswagen TDI engine for two different fuel types (ULSD and B20) and six speed/load combinations., as well as from a Cummins ISX heavy-duty engine using the Westport pilot-ignited high-pressure direct-injection (HPDI) natural-gas fuelling system for three different speed/load combinations. The transmission electron microscopy (TEM) was employed to investigate the soot morphology, emphasizing the fractal properties. Image processing was used to extract the geometrical properties of the thirty-five randomly chosen aggregates from each sample.

Natural gas has a high auto-ignition temperature, therefore natural gas engines use sparks, hot surfaces or separate diesel pilot injects to promote ignition. For example, the high-pressure direction-injection (HPDI) system, available commercially for heavy-duty truck engines, uses a small diesel injection just prior to the main gas injection. A new type of HPDI injector has been developed that injections diesel and gas simultaneously through the same holes. In this paper the operation and flow characteristics of this “co-injector” will be discussed. An injection visualization chamber (IVC) was developed for optical characterization of injections into a chamber at pressures up to 80 bar. A fuel supply system was constructed for precise control of injector fueling and injection timing. Diesel and natural gas are replaced by VISCOR ® and nitrogen to study non-reacting flows.

A new fuel injector prototype for heavy-duty engines has been developed to use direct-injection natural gas with small amounts of entrained diesel as an ignition promoter. This “co-injection” is quite different from other dual-fuel engine systems, where diesel and gas are introduced separately. Reliable compression-ignition can be attained, but two injections per engine cycle are needed to minimize engine knock. In the present paper the interactions between diesel injection mass, combustion timing, engine load, and engine speed are investigated experimentally in a heavy-duty single-cylinder engine. For the tests with this injector, ignition delay ranged from 1.2–4.0 ms (of which injector delay accounts for ~0.9 ms). Shorter ignition delays occurred at higher diesel injection masses and advanced combustion timing. At ignition delays shorter than 2.0 ms, knock intensity decreased with increasing ignition delay.

An experimental investigation of the autoignition of transient gaseous fuel jets in heated and compressed air is conducted in a shock tube facility. Experiments are performed at an initial pressure of 30 bar with initial oxidizer temperatures ranging from 1150 K to 1400 K, injection pressures ranging from 60 bar to 150 bar, and with injector tip orifice diameters of 0.275 mm and 1.1 mm. Under the operating conditions studied, increasing temperature results in a significant decrease in autoignition delay time, td. The smaller orifice results in an increase in ignition delay time and variability, as compared with the larger orifice. For initial temperatures below about 1250K, ignition is rarely achieved with the smaller orifice, whereas ignition is always achieved with the larger orifice down to 1150 K. Under the conditions studied, increasing the injection pressure decreases ignition delay, a result dynamically consistent with larger orifice size decreasing ignition delay time.

The use of exhaust gas recirculation (EGR) to control NOx emissions from direct-injection engines results in the reintroduction of exhaust particulate matter (PM) into the intake manifold. The influence of this recirculated PM on emissions from a pilot-ignited direct injection of natural gas engine was studied by installing a filter in the EGR system. Comparison tests at fixed engine conditions were conducted to identify differences between filtered and unfiltered EGR. No significant variations in gaseous or PM mass emissions were detected. This indicates that the recirculated PM is not contributing substantially to the increases in PM mass emissions commonly observed with EGR. Reductions in black carbon and ultra-fine particle exhaust concentrations in the exhaust were observed at the highest EGR fractions with the filter installed.

A diesel pilot-ignited, high-pressure direct-injection of natural gas heavy-duty single-cylinder engine was fuelled with both natural gas and blends of 10% and 23% by volume hydrogen in methane. A single operating condition (6 bar GIMEP, 0.5 ϕ, 800 RPM, 40%EGR) was selected, and the combustion phasing was varied from advanced (mid-point of combustion at top-dead-center) to late (mid-point of combustion at 15°ATDC). Replacing the natural gas with hydrogen/methane blend fuels was found to have a significant influence on engine emissions and on combustion stability. The use of 10%hydrogen was found to slightly reduce PM, CO, and tHC emissions, while improving combustion stability. 23%hydrogen was found to substantially reduce CO and tHC emissions, while slightly increasing NOx. The greatest reductions in CO and tHC, along with a significant reduction in PM, were observed at the latest combustion timings, where combustion stability was lowest.

Measurements of ignition characteristics and emissions were made in a shock tube facility operating at engine-relevant conditions. Methane and methane/ethane fuels were injected down the centerline of the shock tube using an electronically controlled prototype gaseous fuel injector developed by Westport Innovations. Air was preheated and compressed using a reflected shock technique that produced run times of 4-5 ms. Particulate matter (PM) emissions were found to be highly intermittent. In only 6 out of 97 experiments was PM detected above background levels. In all of these 6 sooting experiments ignition kernels were located relatively close to the injector tip and ignition occurred prior to the end of fuel injection. Using the large orifice injector tip with pure methane fuel, PM was detected in 4 out of 28 experiments; using the small orifice with pure methane fuel, no PM was detected in any of 50 experiments.

The use of pilot-ignited, direct-injected natural gas in a heavy-duty compression-ignition engine has been shown to reduce emissions while maintaining performance and efficiency. Adding recirculated exhaust gas (EGR) has been shown to further reduce emissions of nitric oxides (NOx), albeit at the cost of increased hydrocarbons (tHC), carbon monoxide (CO), and particulate matter (PM) emissions at high EGR fractions. Previous tests have suggested that reducing the delay between the diesel and natural gas injections, increasing the injection pressure, or adjusting the combustion timing have individually achieved substantial emissions benefits. To investigate the effectiveness of combining these techniques, and of using them over a wide range of operating conditions, a series of tests were carried out. The first set of tests investigated the interactions between these effects and the EGR fraction.

Determining what exhaust gas recirculation (EGR) control parameters have the largest impact on engine performance and emissions is of critical importance when developing an EGR-equipped engine. These tests studied the effects of varying the net charge mass, the fresh air charge mass, the indicated power, and the oxygen equivalence ratio at various EGR fractions. The research was carried out on a direct-injection, natural gas fuelled, pilot-ignited four-stroke heavy-duty engine using Westport Innovations Inc.'s pilot-ignited, direct injection of natural gas technology. The testing was carried out using a prototype injector and the standard diesel-fuelled engine's combustion chamber. The results indicate that fuel efficiency, as well as emissions of Nitrogen Oxides (NOx) and Carbon Monoxide (CO) depend primarily on the EGR level, and not on the values of the EGR control parameters.

Pilot-ignited direct injection of natural gas fuelling of a heavy-duty compression ignition engine while using recirculated exhaust gas (EGR) has been shown to significantly reduce NOx emissions. To further investigate emissions reductions, the combustion timing, injection pressure, and relative delay between the pilot and main fuel injections were varied over a range of EGR fractions while engine speed, net charge mass, and oxygen equivalence ratio were held constant. PM emissions were reduced by higher injection pressures without significantly affecting NOx at all EGR conditions. By delaying the combustion, NOx was reduced at the expense of increased PM for a given EGR fraction. By reducing the delay between the pilot and main fuel injections at high EGR, PM emissions were substantially reduced at the expense of increased total hydrocarbon (tHC) emissions. In this research, no attempt was made to optimize the injector or combustion chamber for natural gas fuelling with EGR.