Search Results

To improve the mixing of fuel and air in the combustion chamber of current diesel engines, research is carried out regarding injectors with a porous nozzle tip, replacing conventional nozzles with a limited number of holes. Preliminary tests with porous injectors showed that further research concerning spray distribution was necessary due to non-optimal spray shapes and low fuel velocities. Therefore, spray shapes and fuel velocities of porous injectors were examined at atmospheric pressures. These examinations show that the spray shapes can be adjusted by alternating the geometries. Geometrical influences have been studied and compared to conventional injectors, showing that the fuel velocity of the porous injectors has decreased with approximately a factor of 10. Subsequently, research concerning the lifetime of porous nozzles was necessary due to premature failure.

Controlling ignition delay is the key to successfully enable partially premixed combustion in diesel engines. This paper presents experimental results of partially premixed combustion in an optically accessible engine, using primary reference fuels in combination with artificial exhaust gas recirculation. By changing the fuel composition and oxygen concentration, the ignition delay is changed. To determine the position of the flame front, high-speed visualization of OH-chemiluminescence is used, enabling a cycle-resolved analysis of OH formation. A clear correlation is observed between ignition delay and flame location. The mixing of fuel and air during the ignition delay period defines the local equivalence ratio, which is estimated based on a spherical combustion volume for each spray. The corresponding emission measurements using fast-response analyzers of CO, HC and NOX confirm the decrease in local equivalence ratio as a function of ignition delay.

In earlier research, a new class of bio-fuels, so-called cyclic oxygenates, was reported to have a favorable impact on the soot-NOx trade-off experience in diesel engines. In this paper, the soot-NOx trade-off is compared for two types of cyclic oxygenates. 2-phenyl ethanol has an aromatic and cyclohexane ethanol a saturated or aliphatic ring structure. Accordingly, the research is focused on the effect of aromaticity on the aforementioned emissions trade-off. This research is relevant because, starting from lignin, a biomass component with a complex poly-aromatic structure, the production of 2-phenyl ethanol requires less hydrogen and can therefore be produced at lower cost than is the case for cyclohexane ethanol.

Recently, some studies have shown high efficiencies using controlled auto-ignition by blending gasoline and diesel to a desired reactivity. This concept has been shown to give high efficiency and, because of the largely premixed charge, low emission levels. The origin of this high efficiency, however, has only partly been explained. Part of it was attributed to a lower temperature combustion, originating in lower heat losses. Another part of the gain was attributed to a faster, more Otto-like (i.e. constant volume) combustion. Since the concept was mainly demonstrated on one single test setup so far, an experimental study has been performed to reproduce these results and gain more insight into their origin. Therefore one cylinder of a heavy duty test engine has been equipped with an intake port gasoline injection system, primarily to investigate the effects of the balance between the two fuels, and the timing of the diesel injection.

Increasing fuel prices keep bringing attention to alternative, cheaper fuels. Liquefied Petroleum Gas (LPG) has been well known for decades as an alternative fuel for spark ignition (SI) passenger cars. More recently, aftermarket LPG systems were also introduced to Heavy Duty transport vehicles. These (port fuel) systems either vaporize the liquid fuel and then mix it with intake air, or inject fuel into the engine's intake ports. While this concept offers significant fuel cost reductions, for aftermarket certification and large-scale OEM use some concerns are present. Unburned hydrocarbons (UHC) and carbon monoxide (CO) emissions are known to be high because of premixed charge getting trapped into crevices and possibly being blown through during valve-overlap. Apart from the higher emission levels, this also limits fuel efficiency and therefore cost savings.

Premixed Charge Compression Ignition (PCCI) is a combustion concept that holds the promise of combining emission levels of a spark-ignition engine with the efficiency of a compression-ignition engine. In a short term scenario, PCCI would be used in the lower load operating range only, combined with conventional diesel combustion at higher loads. This scenario relies on using near standard components and conventional fuels; therefore a set of fuels is selected that only reflects short term changes in diesel fuel composition. Experiments have been conducted in one dedicated test cylinder of a modified 6-cylinder 12.6 liter heavy duty DAF engine. This test cylinder is equipped with a stand-alone fuel injection system, EGR circuit and air compressor. For the low load operating range the compression ratio has been lowered to 12:1 by means of a thicker head gasket.

Two of the most pressing challenges of the automotive sector are reduction of fuel consumption and corresponding emission of greenhouse gases, especially when taking into account the growing degree of luxury in modern passenger cars, which increases the auxiliary load on the engine. Preferably, this increase in auxiliary load is compensated by the recovery of waste energy. To accomplish this, a technology called WEDACS (Waste Energy Driven Air Conditioning System) is being developed to recover throttling losses. WEDACS uses a turbine to induce provide the engine with the same air mass flow rate as a throttle valve while producing mechanical energy and cold air. An alternator coupled to this turbine converts mechanical energy into electrical energy and the cold air is used to cool A/C fluid. This way the load of both the engine mounted alternator and A/C compressor is reduced or eliminated, resulting in higher efficiency.

The main goal of this paper is to acquire more insight into the relationship between wall and piston impingement of liquid fuel and unburnt hydrocarbon emissions (UHC) emissions, under early direct injection (EDI) premixed charge compression ignition (PCCI) operating conditions. To this end, the vaporization process is modeled for various operating conditions using a commercial CFD code (StarCD). Predicted values for liquid core penetration, or liquid length LL , have been successfully checked against experimental data from literature over a wide range of operating conditions. Next, the correlation between the CFD results for wall and piston impingement and measured UHC emissions is studied. The diesel fuel used in the experiments is modeled as n-dodecane and n-heptadecane, representing the low and high end of the diesel boiling range, respectively. A distinction is made between liquid spray impingement on the piston surface and cylinder liner.

Lowering diesel engine emission levels, while preserving performance, is the main demand in the development of current and future diesel engines. To fulfill it, the in-cylinder vaporization and combustion processes of the diesel spray must be well understood. An important parameter in the vaporization process of a diesel spray is the maximal penetration distance of liquid fuel (i.e. the “liquid length”). So-called mixing-limited vaporization models assume that the vaporization rate of the fuel is limited by the mixing rate of fuel and ambient gas. Such models have been shown in the literature to accurately correlate liquid lengths for moderate to high in-cylinder densities, i.e. in the density range relevant to modern diesel engines. Since in-cylinder pressures can reach high absolute levels, real gas effects should be considered in these models.

In the port injected Spark Ignition (SI) engine, the single greatest part load efficiency reducing factor are energy losses over the throttle valve. The need for this throttle valve arises from the fact that engine power is controlled by the amount of air in the cylinders, since combustion occurs stoichiometrically in this type of engine. In WEDACS (Waste Energy Driven Air Conditioning System), a technology patented by the Eindhoven University of Technology, the throttle valve is replaced by a turbine-generator combination. The turbine is used to control engine power. Throttling losses are recovered by the turbine and converted to electrical energy. Additionally, when air expands in the turbine, its temperature decreases and it can be used to cool air conditioning fluid. As a result, load of the alternator and air conditioning compressor on the engine is decreased or even eliminated, which increases overall engine efficiency.

One of the challenges with conventional diesel engines is the emission of soot. To reduce soot emission whilst maintaining fuel efficiency, an important pathway is to improve the fuel-air mixing process. This can be achieved by creating small droplets in order to enhance evaporation. Furthermore, the distribution of the droplets in the combustion chamber should be optimized, making optimal use of in-cylinder air. To deal with these requirements a new type of injector is proposed, which has a porous nozzle tip with pore diameters between 1 and 50 μm. First, because of the small pore diameters the droplets will also be small. From literature it is known that (almost) no soot is formed when orifice diameters are smaller than 50 μm. Second, the configuration of the nozzle can be chosen such that the whole cylinder can be filled with fine droplets (i.e., spray angle nearly 180°).

Early Direct Injection Premixed Charge Compression Ignition (EDI PCCI) is a widely researched combustion concept, which promises soot and CO2 emission levels of a spark-ignition (SI) and compression-ignition (CI) engine, respectively. Application of this concept to a conventional CI engine using a conventional CI fuel faces a number of challenges. First, EDI has the intrinsic risk of wall-wetting, i.e. collision of fuel against the combustion chamber periphery. Second, engine operation in the EDI regime is difficult to control as auto-ignition timing is largely decoupled from fuel injection timing. In dual-mode PCCI engines (i.e. conventional Dl at high loads) wall-wetting should be prevented by selecting appropriate (most favorable) operating conditions (EGR level, intake temperature, injection timing-strategy etc.) rather than by redesign of the engine (combustion chamber shape, injector replacement etc.).

This paper first compares strengths and weaknesses of different options for performing optical diagnostics on HD diesel sprays. Then, practical experiences are described with the design and operation of a constant volume test cell over a period of more than five years. In this test rig, pre-combustion of a lean gas mixture is used to generate realistic gas mixture conditions prior to fuel injection. Spray growth, vaporization are studied using Schlieren and Mie scattering experiments. The Schlieren set-up is also used for registration of light emitted by the combustion process; this can also provide information on ignition delay and on soot lift-off length. The paper further describes difficulties encountered with image processing and suggests methods on how to deal with them.

Collision of injected fuel spray against the cylinder liner (wall-wetting) is one of the main hurdles that must be overcome in order for early direct injection Premixed Charge Compression Ignition (EDI PCCI) combustion to become a viable alternative for conventional DI diesel combustion. Preferably, the prevention of wall-wetting should be realized in a way of selecting appropriate (most favorable) operating conditions (EGR level, intake temperature, injection timing-strategy etc.) rather than mechanical modification of an engine (combustion chamber shape, injector replacement etc.). This paper presents the effect of external uncooled EGR (different fraction) on wall-wetting issues specified by two parameters, i.e. measured smoke number (experiment) and liquid spray penetration (model).