Search Results

Steering system is responsible for providing a precise directional control to the vehicle. The Hydraulic Power Assisted Steering (HPAS) system is commonly used in passenger cars and commercial vehicles due to low cost. Power steering pump develops and delivers required pressure to provide assistance while steering. It reduces the effort required to steer the vehicle. Steering pump (generally vane type) is a critical part providing hydraulic pressure assistance to rack and pinion or gear box. Basically the hydraulic pump noise can be classified as ‘Moan Noise’ and ‘Whine Noise’. The noise generated by power steering pump pressure pulsation is termed as ‘Moan’ and ‘Whine’ based on operational induce frequency. As power train becomes quieter, it becomes more perceivable at typical engine operating speed range and gives impression of poor refinement and quality.

Tailgate stoppers play vital role in exerting preload on the Tailgate latch mechanism and also restrict the relative motion of the Tailgate against vehicle Body in White (BIW). These stoppers act as over-slam dampeners and reduce the transmissibility of vibrations thereby reduce the risk of Squeaks & Rattles (S&R) noises. S&R noises from Tailgate are most annoying to the rear passengers in the vehicle and are recurring in nature. Preventing these issues during design is a challenging task. S&R risk simulations enable us to conduct virtual Design of Experiments (DOEs) and arrive at optimal solutions. This approach helps in reducing the cost of the design changes that are required in the physical prototype at the later stages of product development and save time. The risk evaluation in the simulations is based on the relative displacement at the interfaces of two components.

To cope up with the market requirements, OEMs need to react fast and develop advanced and highly refined vehicles keeping in mind multiple factors and Perceived Quality is one of the most important amongst those. Annoying squeak and rattle noises from the vehicle, whether it is new or used car, is the most customer irritant factor; which needs to be addressed in the vehicle development program. BSR (Buzz, Squeak and Rattle) and NVH (Noise, Vibrations and Harshness) performance is the critical in providing quieter experience to the customer and it is becoming more and more important due to transformation from ICE (Internal Combustion Engine) to Hybrid and Electric Powertrains. Among BSR noises, body squeak and creak is the most annoying and difficult to detect and correct, if reported on the prototype test or customer cars. Whereas, squeak and rattles from body fitment and underbody aggregates are relatively easy to address and correct.

Traditionally, vehicle ride and comfort is evaluated, subjectively as well as objectively. Based on the outcome of subjective and objective tests, it is refined by optimizing primary suspension system, secondary suspension system, seating system, rubber bushings, frame and BIW for mass, stiffness, damping, geometry etc. Many a time subjective assessment results stands in contradiction to the objective assessment results; emphasizing need for having good correlation between subjective and objective test results. In such cases, it is ambiguous to decide suitable design refinement action and can lead to no improvement situation. Hence, it is essential to have concurring test procedures for subjective and objective ride evaluation. This paper describes a novel methodology to address the above said challenge. There are defined set of test events and measurement data points to be used in subjective and objective testing.

The traditional method of collecting the Road Torque Data of a vehicle is by instrumenting and running the vehicle on different road terrains. Every time, physical testing becomes tedious & most challenging task due to unavailability of unit under tests, kind of resource required and so on. However, in view of response to the fast emerging technology & limit less competition, it has become mandatory to develop & launch products in market within no time. In recent times, there is increased demand for physical road torque data measurements for a vehicle program based on its application and different powertrain configurations, which clearly shows that unless we front load the data to design it is practically impossible to meet the deadlines. Each of these measurements cost and consumes valuable resources of the company in collecting and analyzing the data.

Vehicle floor vibration is the resultant of different road inputs damped through various transfer paths. Seat comfort, which depends on these floor vibrations, can be evaluated with a single input signal “Pink noise”; which constitutes various road inputs. Transmissibility of seat structure on a vibration shaker with pink noise input includes all possible responses of road inputs. Still, transmissibility profile at vehicle end and component level varies. This is due to the utilization of “dummy” on component level testing on vibration shaker, which acts as a dead weight with dissimilar damping characteristics of human. A transmissibility correlation between human and dummy is attained by replacing the dummy in place of human and actuating it to find the difference in contribution between them for different class of vehicles. This contribution extrapolation from the damping effects of human and dummy is applied on dummy transmissibility.